Instrukcja obsługi Aruba AP-93H

Aruba Punkt dostępu AP-93H

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Aruba AP-93H (2 stron) w kategorii Punkt dostępu. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Aruba AP-93H Wireless Access Point

Installation Guide

The Aruba AP-93H are single-radio, dual-band wireless access point that

supports the IEEE 802.11n standard for high-performance WLAN. This access

point uses MIMO (Multiple-in, Multiple-out) technology and other high-

throughput mode techniques to deliver high-performance, 802.11n 2.4 GHz or 5

GHz functionality while simultaneously supporting existing 802.11a/b/g wireless

services. The AP-93H access point works only in conjunction with an Aruba

Controller.

The Aruba AP-93H access point provides the following capabilities:

Wireless transceiver

Protocol-independent networking functionality

IEEE 802.11a/b/g/n operation as a wireless access point

IEEE 802.11a/b/g/n operation as a wireless air monitor

Compatibility with IEEE 802.3af PoE

Central management configuration and upgrades through an Aruba

Controller

Package Contents

AP-93H Access Point

AP-93H Mounting Bracket

1x Security Screw

2x Cat5e Ethernet cable (length 0.1m)

Installation Guide

AP-93H Hardware Overview

Figure 1 Top

LEDs

PWR: Indicates whether or not the AP-93H is powered-on

ENET 0: Indicates the status of ENET 0

11A/N: Indicates the status of the 802.11a/n radio

11B/G/N: Indicates the status of the 802.11b/g/n radio

For information about the AP-93H’s LED behavior, see .Table 1

Figure 2 Rear

Serial Console Port

The serial console port (Console) allows you to connect the AP to a serial

terminal or a laptop for direct local management. This port is an RJ-45 female

connector with the pinouts described in . Connect this port directly to a Figure 3

terminal or terminal server using an Ethernet cable.

Figure 3 Serial Port Pin-Out

Figure 4 Bottom

Ethernet Ports

AP-93H is equipped with a total of five active Ethernet ports (ENET 0-5). ENET 0

is a 10/100/1000Base-T (RJ-45) auto-sensing, MDI/MDX wired-network uplink

connectivity port. This port supports IEEE 802.3af Power over Ethernet (PoE),

accepting 48VDC as a standard defined Powered Device (PD) from a Power

Sourcing Equipment (PSE) such as a PoE midspan injector or network

infrastructure that supports PoE. ENET 1 through 4 are 10/100Base-T (RJ-45)

auto-sensing, MDI/MDX wired-network downlink connectivity ports, used to

provide secure network connectivity to wired devices. ENET 0 is located on the

rear of the AP, while ENET 1-4 are located on the bottom ( ).Figure 4

Additionally, AP-93H supports a passive pass-through RJ-45 interface to extend a

physical connection (typically another Ethernet connection) from the back of

the device to a connector on the bottom.

Figure 5 Gigabit Ethernet Port Pin-Out

Figure 6 Fast Ethernet Port Pin-Out

DC Power Socket

The AP-93H has a single 12V DC power jack socket to support powering through

an AC-to-DC power adapter.

Reset Button

The reset button can be used to return the AP to factory default settings. To reset

the AP:

1. Power off the AP.

2. Press and hold the reset button using a small, narrow object, such as a

paperclip.

3. Power-on the AP without releasing the reset button. The power LED will

flash within 5 seconds.

4. Release the reset button.

The power LED will flash again within 15 seconds indicating that the reset is

completed. The AP will now continue to boot with the factory default settings.

Before You Begin

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their

placement have been determined, the Aruba controller(s) must be installed and

initial setup performed before the Aruba APs are deployed.

AP Pre-Installation Checklist

Before installing your AP-93H access point, be sure that you have the following:

Pre-installed wall box

Cat5 UTP cable with network access installed in the wall box

One of the following power sources:

IEEE 802.3af-compliant Power over Ethernet (PoE) source

Aruba AP AC-DC adapter kit (sold separately)

Aruba Controller provisioned on the network:

Layer 2/3 network connectivity to your access point

One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor-specific options

Summary of the Setup Process

Successful setup of an AP-93H access point consists of five tasks, which must be

performed in this order:

1. Verify pre-installation connectivity.

2. Identify the specific installation location for each AP.

3. Install each AP.

4. Verify post-installation connectivity.

5. Configure each AP.

Verifying Pre-Installation Connectivity

Before you install APs in a network environment, make sure that the APs are

able to locate and connect to the controller after power on. Specifically, you

must verify the following conditions:

When connected to the network, each AP is assigned a valid IP address

APs are able to locate the controller

Refer to the Guide for instructions on locating and ArubaOS Quick Start

connecting to the controller.

Identifying Specific Installation Locations

You can mount the AP-93H access point on a wall or on the ceiling. Use the AP

placement map generated by Aruba’s RF Plan software application to determine

the proper installation location(s). Each location should be as close as possible

to the center of the intended coverage area and should be free from obstructions

or obvious sources of interference. These RF absorbers/reflectors/interference

sources will impact RF propagation and should have been accounted for during

the planning phase and adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference

Sources

Identifying known RF absorbers, reflectors, and interference sources while in

the field during the installation phase is critical. Make sure that these sources are

taken into consideration when you attach an AP to its fixed location.

RF absorbers include:

Cement/concrete—Old concrete has high levels of water dissipation, which

dries out the concrete, allowing for potential RF propagation. New concrete

has high levels of water concentration in the concrete, blocking RF signals.

Natural Items—Fish tanks, water fountains, ponds, and trees

Brick

RF reflectors include:

Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/

heating ducts, mesh windows, blinds, chain link fences (depending on

aperture size), refrigerators, racks, shelves, and filing cabinets.

Do not place an AP between two air conditioning/heating ducts. Make sure

that APs are placed below ducts to avoid RF disturbances.

RF interference sources include:

Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)

Cordless headset such as those used in call centers or lunch rooms

Installing the AP

The AP-93H is designed to mount into a variety of electrical gang boxes. To

install your AP-93H:

1. Begin by removing the existing data wall plate (if applicable).

Figure 7 Removing the Wall Plate

2. Remove any existing RJ45 connectors (typically snap-in) or cut/remove the

UTP cable.

3. Use the short Ethernet cables supplied with the AP-93H to connect the AP to

the RJ45 connectors or crimp an RJ45 plug (not supplied) on the cable (or

both cables if using the pass through).

4. Align the mounting holes of the AP-93H mounting bracket with mounting

holes in you gang box as shown in .Figure 8

The Aruba AP-93H requires ArubaOS 6.1.3 or later.

Inform your supplier if there are any incorrect, missing, or damaged

parts. If possible, retain the carton, including the original packing

materials. Use these materials to repack and return the unit to the

supplier if needed.

Console

Port ENET 0

Pass

Through

Port

If both POE and DC power are available, the AP uses POE even when

there is not enough POE voltage available to power the AP.

Serial

Console Port

TxD

GND

RxD

RJ-45 Female

Pin-Out

GND

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out 1

Spare Pair

ETH Rx+

ETH Rx-

ETH Tx+

ETH Tx-

(POE positive)

(POE negative)

(POE positive)

10/100 Mbps Ethernet   ee

nt

Spare Pair



ETH Tx+

ETH Tx–

ETH Rx+

ETH Rx–

FCC Statement: Improper termination of access points installed in

the United States configured to non-US model controllers will be in

violation of the FCC grant of equipment authorization. Any such willful

or intentional violation may result in a requirement by the FCC for

immediate termination of operation and may be subject to forfeiture

(47 CFR 1.80).

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz

bands. Please refer to the for details on ArubaOS User Guide

restrictions.

Produit réseau local radio basse puissance operant dans la bande

fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User

Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band

arbeitet. Weitere Informationen bezlüglich Einschränkungen finden

Sie im ArubaOS User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz.

Fare riferimento alla per avere informazioni ArubaOS User Guide

detagliate sulle restrizioni.

It is important that you verify the items listed under AP Pre-Installation

Checklist before you attempt to set up and install an AP-93H.

Aruba Networks, Inc., in compliance with governmental requirements, has

designed the AP-93H access points so that only authorized network

administrators can change the settings. For more information about AP

configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User

Guide.

Access points are radio transmission devices and as such are subject to

governmental regulation. Network administrators responsible for the

configuration and operation of access points must comply with local

broadcast regulations. Specifically, access points must use channel

assignments appropriate to the location in which the access point will be

used.

The following procedure describes a typical installation using a standard

United States wall box.

Aruba AP-93H Wireless

Access Point

Installation Guide

www.arubanetworks.com

1344 Crossman Avenue

Sunnyvale, California 94089

Phone: 408.227.4500

Fax 408.227.4550

Aruba AP-93H Wireless Access Point | Installation Guide

Part Number 0510703-01 | November 2011

Contacting Aruba Networks

Table 1

Web Site Support

Main Site http://www.arubanetworks.com

Support Site https://support.arubanetworks.com

Software Licensing Site https://licensing.arubanetworks.com/login.php

Wireless Security Incident

Response Team (WSIRT)

http://www.arubanetworks.com/support/wsirt.php

Americas and APAC Support Email support@arubanetworks.com

EMEA Support Email emea.support@arubanetworks.com

WSIRT Email

Please email details of any security

problem found in an Aruba product.

wsirt@arubanetworks.com

Table 2

Telephone Support

Aruba Corporate +1 (408) 227-4500

FAX +1 (408) 227-4550

Support

United States

Universal Free Phone Service Number (UIFN): Australia, Canada,

China, France, Germany, Hong Kong, Ireland, Israel, Japan, Korea,

Singapore, South Africa, Taiwan, and the UK

All Other Countries

800-WI-FI-LAN (800-943-4526)

+800-4WIFI-LAN (+800-49434-526)

+1 (408) 754-1200

For Wireless That Works®, Mobile Edge Architecture, People Move. Networks Must Follow., RFprotect

®, The All

Wireless Workplace Is Now Open For Business, and The Mobile Edge Company® are trademarks of Aruba

Open Source Code

Certain Aruba products include Open Source software code developed by third parties, including software code

subject to the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open

Source Licenses. The Open Source code used can be found at this site:

http://www.arubanetworks.com/open_source

Legal Notice

The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate

other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for

this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against

it with respect to infringement of copyright on behalf of those vendors.

Warranty

This hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information,

refer to the ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS.

Altering this device (such as painting it) voids the warranty.

Figure 8 Bracket to Gang Box (Standard US Single Gang Outlet Box Shown)

5. Connect any required cables to the rear of the AP-93H.

6. Align the mounting posts on the mounting bracket with the corresponding

mounting holes on the back of your AP-93H as shown in .Figure 9

Figure 9 AP-93H to Bracket

7. Securing your AP-93H to the mounting bracket using the enclosed security

screw (see ).Figure 10

Figure 10 Securing the AP-93H

8. If not using PoE, connect the AC-DC power adapter (sold seperately) to the

DC power socket located on the bottom of the AP-93H.

Verifying Post-Installation Connectivity

.The integrated LEDs on the AP can be used to verify that the AP is receiving

power and initializing successfully (see ). Refer to the Table 1 ArubaOS Quick

Start Guide for further details on verifying post-installation network connectivity

Configuring the AP-93H

AP Provisioning/Reprovisioning

Provisioning parameters are unique to each AP. These local AP parameters are

initially configured on the controller which are then pushed out to the AP and

stored on the AP itself. Aruba recommends that provisioning settings be

configured via the ArubaOS Web UI only. Refer to the for ArubaOS User Guide

complete details.

AP Configuration

Configuration parameters are network or controller specific and are configured

and stored on the controller. Network configuration settings are pushed out to

the AP(s) but remain stored on the controller.

Configuration settings can be configured via the ArubaOS Web UI, ArubaOS CLI,

or Aruba MMS. Refer to their respective guides for further details: the ArubaOS

User Guide Aruba Mobility Management System User Guide or .

Product Specifications

Electrical

Ethernet:

1 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interface (ENET 0)

4 x 10/100Base-T auto-sensing Ethernet RJ-45 Interfaces (ENET 1)

MDI/MDX

IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab

(1000Base-T)

Power over Ethernet (IEEE 802.3af compliant), 48V DC/350mA (see Figure

5 for pin configuration)

Power:

48V DC 802.3af Power over Ethernet

12 VDC power interface, supports powering through an AC-to-DC power

adapter

For additional specifications on this product, please refer to the data sheet. The

data sheet can be found at .www.arubanetworks.com

Proper Disposal of Aruba Equipment

For the most current information about Global Environmental Compliance and

Aruba products, see our website at .www.arubanetworks.com

Waste of Electrical and Electronic Equipment

Aruba products at end of life are subject to separate collection

and treatment in the EU Member States, Norway, and

Switzerland and therefore are marked with the symbol shown at

the left (crossed-out wheelie bin). The treatment applied at end

of life of these products in these countries shall comply with the

applicable national laws of countries implementing Directive

2002/96EC on Waste of Electrical and Electronic Equipment (WEEE).

European Union RoHS

Aruba products also comply with the EU Restriction of

Hazardous Substances Directive 2002/95/EC (RoHS). EU

RoHS restricts the use of specific hazardous materials in

the manufacture of electrical and electronic equipment. Specifically, restricted

materials under the RoHS Directive are Lead (including Solder used in printed

circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine.

Some Aruba products are subject to the exemptions listed in RoHS Directive

Annex 7 (Lead in solder used in printed circuit assemblies). Products and

packaging will be marked with the “RoHS” label shown at the left indicating

conformance to this Directive.

China RoHS

Aruba products also comply with China environmental declaration

requirements and are labeled with the “EFUP 10” label shown at the

left.

Safety and Regulatory Compliance

Aruba Networks provides a multi-language document that contains country-

specific restrictions and additional safety and regulatory information for all

Aruba access points. This document can be viewed or downloaded from the

following location: www.arubanetworks.com/safety_addendum

EMC Compliance and Warning Statement

This equipment generates, uses and can radiate radio frequency energy, and, if

not installed and used in accordance with the manufacturer’s instructions may

cause harmful interference to other devices in the vicinity. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment causes interference with other devices, which may be determined by

turning the equipment off and on, the user is encouraged to try and correct the

interference by one or more of the following measures:

Reorient or relocate the device receiving the interference.

Increase the separation between the equipment.

Connect the equipment into an outlet on a circuit different from that to which

the other device(s) are connected.

Consult the manufacturer or field service technician for help.

The protection against electric shock is Class ll.

Equipment not suitable for use in the presence of flammable mixtures.

Table 1 AP-93H Series LED Meanings

LED Color/State Meaning

PWR Off No power to AP

Green flashing System initializing

Red steady System failed to initialize, contact

TAC

Green steady Power on, device ready

ENET 0 Off No link

Green on 1000 Mbps link

Amber on 10/100 Mbps link

Flashing Ethernet link activity

ENET 1-4 Off No link

Green on 10/100 Mbps link

Flashing Ethernet link activity

11A/N Off 5 GHz radio is disabled

Amber 5 GHz radio enabled in WLAN mode

Green 5 GHz radio enabled in 11n mode

Green flashing 5 GHz Air Monitor

11B/G/N Off 2.4 GHz radio disabled

Amber 2.4 GHz radio enabled in WLAN mode

Green 2.4 GHz radio enabled in 11n mode

Green flashing 2.4 GHz Air Monitor

If a power adapter other than the one provided by Aruba Networks is

used in the US or Canada, it should be NRTL Listed, with an output rated

12 VDC, minimum 1.25A, marked “LPS” or “Class 2,” and suitable for

plugging into a standard power receptacle in the US and Canada.

Table 1 AP-93H Series LED Meanings (Continued)

LED Color/State Meaning

Aruba access points must be installed by a professional installer. The

professional installer is responsible for ensuring that grounding is

available and it meets applicable local and national electrical codes.

RF Radiation Exposure Statement: This equipment complies with FCC

RF radiation exposure limits. This equipment should be installed and

operated with a minimum distance of 7.87 inches (20cm) between the

radiator and your body for 2.4 GHz and 5 GHz operations. This

transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter. When operated in the 5.15 to 5.25 GHz

frequency range, this device is restricted to indoor use.

᳝↦᳝ᆇ⠽䋼ໄᯢ

᳝↦᳝ᆇ⠽䋼ໄᯢ᳝↦᳝ᆇ⠽䋼ໄᯢ

Hazardous Materials Declaration

᳝↦᳝ᆇ⠽䋼៪ܗ㋴(Hazardous Substance)

䚼ӊৡ⿄

(Parts) 䪙

3E

∲

+J

䬝

&G

݁Ӌ䫀

&U





໮⒈㘨㣃

3%%

໮⒈Ѡ㣃䝮

3%'(

⬉䏃ᵓ

(

PCA Boards)

h ƻ ƻ ƻ ƻ ƻ

ᴎẄ㒘ӊ

(Mechanical Sub-Assemblies) h ƻ ƻ ƻ ƻ ƻ



ƻ˖ 㸼⼎䆹

᳝

↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼

SJ/T11363-2006

ᷛ

ޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟǄ

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is

below the relevant threshold of the SJ/T11363-2006 standard. 



h˖ 㸼⼎䆹

᳝

↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7

ᷛ

ޚ㾘ᅮⱘ䰤䞣㽕∖Ǆ

Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials

in the parts is above the relevant threshold of the SJ/T11363-2006 standard.



ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼Ǆ

This table shows where these substances may be found in the supply chain of electronic information

products, as of the date of sale of the enclosed product.

ℸ

ᷛ

ᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ

᳝

ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ

՟བ⬉∴ऩܗ῵ഫ䌈೼݊ѻકϞ

ℸ

⦃Փ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰

The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are

per the symbol shown here. The Environment- Friendly Use Period is valid only when the

product is operated under the conditions defined in the product manual.

Specyfikacje produktu

Marka:	Aruba
Kategoria:	Punkt dostępu
Model:	AP-93H

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Aruba AP-93H, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Punkt dostępu Aruba

Aruba AP-504 Instrukcja

8 Października 2024

Aruba AP-318 Instrukcja

29 Września 2024

Aruba AP-577 Instrukcja

29 Września 2024

Aruba AP-303H Instrukcja

23 Września 2024

Aruba 175P Instrukcja

19 Września 2024

Aruba Instant IAP-175 Instrukcja

10 Września 2024

Aruba 205H Instrukcja

9 Września 2024

Aruba AP-93H Instrukcja

9 Września 2024

Aruba Instant RAP-108 Instrukcja

31 Sierpnia 2024

Aruba Instant 100 Instrukcja

22 Sierpnia 2024

Instrukcje Punkt dostępu

Najnowsze instrukcje dla Punkt dostępu

Cisco MR12 Instrukcja

14 Października 2024

Draytek VigorAP 920R Instrukcja

13 Października 2024

Netgear WNDAP360 Instrukcja

12 Października 2024

TP-Link Festa F65-Wall Instrukcja

9 Października 2024

D-Link DWL-1000AP+ Instrukcja

9 Października 2024

D-Link DWL-700AP Instrukcja

9 Października 2024

Cambium Networks cnPilot e505 Instrukcja

9 Października 2024

Cambium Networks cnPilot e425H Instrukcja

9 Października 2024

Cambium Networks cnPilot e600 Instrukcja

9 Października 2024

Cambium Networks cnPilot e510 Instrukcja

9 Października 2024