Instrukcja obsługi Black & Decker F65E


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Black & Decker F65E (13 stron) w kategorii Okowy. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/13
Please Read and Save this Use and Care Book
Por favor lea este instructivo antes de usar el producto
Veuillez lire et conserver ce guide d’entretien et d’utilisation
The Classic
Iron
Plancha
Fer
Accessories/Parts (USA/Canada)
Accesorios/Partes (EE.UU/Canadá)
Accessoires/Pièces (É.-U./Canada)
1-800-738-0245
USA/Canada 1-800-231-9786
Mexico 01-800-714-2503
www.blackanddecker.com Models
Modelos
Modèles
F63E
F65E
21
When using your iron, basic safety precautions should always be followed,
including the following:
Read all instructions before using.
Use iron only for its intended use.
To protect against a risk of electric shock, do not immerse the iron in water
or other liquid.
The iron should always be turned off (refer to “How to Use” section) before
plugging into or unplugging from an outlet. Never yank cord to disconnect
from outlet; instead grasp plug and pull to disconnect.
Do not allow cord to touch hot surfaces. Let iron cool completely before
putting away. Loop cord loosely around cord wrap when storing.
Always disconnect iron from electrical outlet when filling with or emptying
of water and when not in use.
Do not operate iron with a damaged cord or if the iron has been dropped or
damaged. To avoid the risk of electric shock, do not disassemble the iron,
take it to a qualified serviceman for examination and repair. Incorrect
reassembly can cause a risk of electric shock when the iron is used.
Close supervision is necessary for any appliance being used by or near
children. Do not leave iron unattended while connected or on an
ironing board.
Burns can occur from touching hot metal parts, hot water, or steam. Use
caution when you turn a steam iron upside down or use the surge of
steam there may be hot water in the water tank. Avoid rapid
movement of iron to minimize hot water spillage.
SPECIAL INSTRUCTIONS
To avoid a circuit overload, do not operate another high-wattage appliance
on the same circuit.
If an extension cord is absolutely necessary, a 10-ampere and 120-volt,
or 6-ampere and 220-volt cord should be used. Cords rated for less
amperage may overheat. Care should be taken to arrange the cord
so that it cannot be pulled or tripped over.
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
POLARIZED PLUG (120V Models Only)
This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electric shock, this plug will fit into a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt to modify the plug
in any way.
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a tamper-resistant screw to prevent
removal of the outer cover. To reduce the risk of fire or electric shock, do not
attempt to remove the outer cover. There are no user-serviceable parts
inside. Repair should be done only by authorized service personnel.
Note: If the power supply cord is damaged, it should be replaced by
qualified personnel or in Latin America by an authorized service center.
How to Use
This appliance is for household use only.
GETTING STARTED
Remove any labels, stickers or tags attached to the body or soleplate of the iron.
Note: Use ordinary tap water for ironing. Do not use water processed through a
home softening system.
Important: For optimum performance, let the iron stand for 90 seconds before
beginning to iron.
FILLING WATER TANK
1. With the iron unplugged and the steam button latched in
the down position, use a clean cup and pour water into
the fill hole . Refill as needed.(A)
2. Plug in the iron and let it stand on its heel rest.
SELECTING TEMPERATURE
1. Use the fabric guide on the iron to select the proper
temperature setting for the fabric to be ironed (B).
Tip: If unsure of a garment's fiber, test a small area (on an
inside seam or hem) before ironing. If there is a brown
buildup on the soleplate, lower the setting and/or reduce
starch.
2. Once you determine the fabric type, set the temperature
selector to the appropriate setting for your fabric (C).
3. When finished ironing, place iron on its heel rest, turn
temperature selector to OFF and unplug the iron.
STEAM IRONING
1. Be sure there is water in the water tank.
2. Turn the temperature selector between settings 5 and 7.
3. Unlatch the steam button to the Up position . If steam(D)
does not start, gently bump the soleplate on the ironing
board a few times. If water drips from vents, turn the
selector to a higher setting.
DRY IRONING
1. Turn the temperature selector to the desired setting and latch the steam button
down. For extended periods of dry ironing, empty the water from the iron.
2. If you want to empty the water, hold the iron over a sink with the tip pointing
down. Water will empty out the fill hole. Stay clear of splashing hot water.
ANTI-DRIP SYSTEM
The anti-drip system prevents water spotting at low temperatures.
4
3
Product may vary slightly from what is illustrated.
1. Water-fill hole
2. Temperature selector
3. Steam button
4. Heel rest
5. Fabric guide
6. Water window
7. Button groove
8. Soleplate
A
B
C
D


Specyfikacje produktu

Marka: Black & Decker
Kategoria: Okowy
Model: F65E

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Black & Decker F65E, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Okowy Black & Decker

Instrukcje Okowy

Najnowsze instrukcje dla Okowy

Tefal

Tefal FV9250 Program8 Instrukcja

15 Października 2024
Termozeta

Termozeta Lella Instrukcja

15 Października 2024
Scarlett

Scarlett SC-131S Instrukcja

13 Października 2024
Bosch

Bosch TDI953222V Instrukcja

13 Października 2024
Alpina

Alpina SF-1303 Instrukcja

13 Października 2024
ECG

ECG NZ 260 Instrukcja

12 Października 2024
Day

Day 72443 Instrukcja

12 Października 2024
Clatronic

Clatronic DBS 3001 Instrukcja

12 Października 2024
Orbegozo

Orbegozo SV 2210 Instrukcja

11 Października 2024
Sunbeam

Sunbeam 3980 Instrukcja

10 Października 2024