Instrukcja obsługi AstralPool ZX Series


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AstralPool ZX Series (8 stron) w kategorii Filtr wody. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/8
INSTALLATION AND
OPERATING INSTRUCTIO NS
Melbourne: 03 8796 8600 Gold Coast: 07 5552 2600 Perth: 08 9350 2600
Sydney: 02 9853 2100 Townsville: 07 4750 3100 sales@astralpool.com.au
Brisbane: 07 3308 5400 Adelaide: 08 8152 7600 www.astralpool.com.au
INSTALLATION AND OPERATING INSTRUCTIONS I INSTALLATION AND OPERATING INSTRUCTIONS
ZX Series Cartridge
Filter
INST 247 ZX Series Cartridge Filter 7. V0 20
2
INST 247 ZX Series Cartridge Filter 7. V0 20
3
INTRODUCTION
Congratulations on the purchase of your AstralPool ZX series cartridge filter.
The ZX series filters are made to last by utilising the best quality materials available. The tank is made from high quality
ABS plastics, capable of withstanding the harshest of environments while DuPont Remay elements are used which are
regarded by the industry as the best available. Include with this Mircoban antimicrobial coating on the elements and
you are sure to achieve one of the cleanest pools possible.
WARNING: DO NOT OVERTIGHTEN LOCKING RING AS THIS MAY CAUSE THE FILTER TO LEAK. GENTLE HAND
TIGHT IS SUFFICIENT FOR CORRECT SEALING.
INSTALLATION OF ZX SERIES
1. Ensure cartridge filter is located on a clean, stable and level base.
2. The ZX series filter has three inlet ports (from pump) and one outlet port (to pool/spa). Glue one of the 50mm slip
tails supplied into one of the inlets and second slip tail supplied into the outlet of the filter that suits the plumbing
configuration.
3. Glue in the supplied blanking cap and drain plug cap into the two remaining inlets. Allow a minimum of one hour
for glue to dry before subjecting filter to system pressures.
4. Glue water connection pipes from pump and pool return to 50mm tails supplied. (Ensure locking nut is placed on
pipe before gluing on tails.
5. Apply Teflon tape (not included) to the pressure gauge and screw into lid where indicated.
START UP INSTRUCTIONS
1. Before starting your ZX filter, make sure the cartridge is in the filter and the lid and lock ring are in place anup d
tightened.
2. Open the suction and return line valves (when fitted).
3. Start pump and open the air release valve on the filter lid 2 to 3 turns air will begin to be forced from the tank.
Once water begins to flow from the valve, tighten to close. Check there is a good flow of water back in the pool. to
4. Clean the cartridge when the flow to the pool reduces or the pressure gauge increases by 15 20 kPa.


Specyfikacje produktu

Marka: AstralPool
Kategoria: Filtr wody
Model: ZX Series

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AstralPool ZX Series, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Filtr wody AstralPool

Instrukcje Filtr wody

Najnowsze instrukcje dla Filtr wody

Philips

Philips ADD6830 Instrukcja

20 Grudnia 2024
JANDY

JANDY CS100 Instrukcja

19 Grudnia 2024
JANDY

JANDY CS150 Instrukcja

19 Grudnia 2024
JANDY

JANDY CS250 Instrukcja

19 Grudnia 2024
Heissner

Heissner HLF6000 Instrukcja

16 Grudnia 2024
Haier

Haier HBU122-3 Instrukcja

10 Grudnia 2024
Haier

Haier HBCF-S3002 Instrukcja

10 Grudnia 2024
Haier

Haier HRO6H85-3 Instrukcja

10 Grudnia 2024