Instrukcja obsługi AMX RDM-2DC

AMX ściemniacz RDM-2DC

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AMX RDM-2DC (1 stron) w kategorii ściemniacz. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

Installation Guide

RDM-2DC Dual DC Dimmer Module 1920W, 0-10 VDC (x2)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

7/08

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-606-61 REV: A

The RDM-2DC Dual DC Module (FG606-61) is a 1920 W module used for the

dimming of fluorescent ballast loads. It uses a 0 to 10 VDC current sinking for

use with four-wire ballasts. It is designed for use with the RDA series of

enclosures, in an AMX Lighting™ modular digital dimming system. The module’s

120 and 277 VAC ratings are CE, UL, and C-UL approved.

RDM-2DC UL and C-UL Ratings

• 120 VAC, 50/60 Hz, 1920 W

• 277 VAC, 50/60 Hz, 1920 W

• Control Out: 50 mA, 12 VDC sinking

Suggested Dimmed Loads

• Four-wire dimmable ballasts, like Advance Transformer Mark VII™ or the

Energy Savings SuperDim™ series

Specifications

• Dimensions (HW): 10" x 2.75" (25.4 cm x 6.99 cm)

• Non-phase dependant

• Use wires rated at 75°C (167°F)

• Torque terminals to 20 in-lbs. (2.3 N/M)

• Max. wire size: 10 AWG (4 mm²)

• Wire stripping length: 0.28" (7 mm)

• Weight: 2.6 lbs. (1.180 kg)

• BTU/hr: 150

• Control current: 125 mA @ 12 VDC per control port

Caution: Pre-Installation Notes

• All Class 1 wiring must be connected to proper terminals.

• All control wiring must be connected to proper terminals.

• Disconnect power while installing or connecting the unit.

• Keep top and bottom air vents clear at all times.

• Use low-voltage wires with a 300 volt rating or greater.

• Use field installed copper conductors.

• All electrical ratings are for continuous duty.

• For indoor use only.

• Test loads for shorts before connecting.

• This module may require extra power from the AXlink connection or an

external power supply connected to the control card.

Connecting the RDM-2DC to the AMX Lighting Master

Lighting Application Drawings

Warning: Failure to ground the ballast may cause ballast failure

FIG. 1 RDM-2DC

Low-voltage control

wiring: 4-pin

Relay

+ out (LV)

- out (LV)

Line in

Load out High

Low-voltage

voltage

connector to AMX

Lighting master

controller

Mounting

points

+ out (LV)

- out (LV)

Line in

Load

High

Low

voltage

Relay

voltage

Fuses

out

FIG. 2 Connecting the RDM-2DC and AMX Lighting Master

FIG. 3 RDM-2DC application wiring

Pin 4 (GND)

Pin 3 (RLY)

Pin 2 (DIM)

Pin 1 (+12 V)

RDM-2DC 4-pin module connector

1 (+)

2 (DIM)

3 (-)

GND

4-pin plug from RDM series module

Note: The 4-pin plugs from the module connector to the 4-pin

connector on the master (black plug cover facing up).

Ballast

Florescent

Neutral

Line in (HOT)

Load

Neutral

Circuit breaker

panel

Ballast

The fuses protect the dimming

circuit from a low impedance load.

• The fuse will blow if it were

incorrectly wired

• Catastrophic ballast failure

• Reversing switched and

dimmed circuits

• Reversing dimmed and

line circuits.

The dimmed output must be

connected to a high impedance

load.

Specyfikacje produktu

Marka:	AMX
Kategoria:	ściemniacz
Model:	RDM-2DC
Typ kontroli:	Niedostępny
Wysokość produktu:	254 mm
Szerokość produktu:	69.9 mm
Waga produktu:	1040 g
Model:	Ściemniacz światła
Obudowa:	Mocowany