Instrukcja obsługi V-TAC VT-80300

V-TAC detektor ruchu VT-80300

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla V-TAC VT-80300 (4 stron) w kategorii detektor ruchu. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

In case of any query/issue with the product, please reach out to us at: support@v-tac.eu

For More products range, inquiry please contact our distributor or nearest dealers.

V-TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul.L.Karavelow 9B

MULTI-LANGUAGE

MANUAL QR CODE

Please scan the QR code to

access the manual in multiple languages.

INSTRUCTION MANUAL

INFRARED MOTION SENSOR

TECHNICAL DATA

MODEL VT-80300

SKU 23161

INPUT POWER AC: 220-240V, 50/60 Hz

RATED LOAD Max. 1200W

300W +LED

TIME DELAY Min. 10sec ±3sec

Max. 15min ±2min

DETECTION

RANGE 180°

DETECTION

DISTANCE 12m max (<24°C)

DETECTION

MOVING SPEED 0.6-1.5m/s

WORKING

TEMPERATURE -20°C to +40°C

WORKING

HUMIDITY <93%RH

POWER

CONSUMPTION Approx, 0.5W

AMBIENT LIGHT <3-2000 LUX (Adjustable)

INSTALLATION

HEIGHT 1.8-2.5m

POWER

CONSUMPTION approx w0.9

DETECTION

MOTION SPEED 0.6-1.5 m/s

DIMENSION 119.5x80x51.5 mm

INTRODUCTION & WARRANTY

Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions

carefully before starting the installation and keep this manual handy for future reference. If you have any another

query, please contact our dealer or local vendor from whom you have purchased the product. They are trained

and ready to serve you at the best. The warranty is valid for 5 years from the date of purchase. The warranty

does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no

warranty against damage to any surface due to incorrect removal and installation of the product.

V-TAC LED

RANGE (UPTO 600W)

COMPATIBLE WITH

This marking indicates that this prod-

uct should not be disposed of with

other household wastes.

Caution, risk of electric shock.

FUNCTION

WARNING

1. Please make sure to turn o the power before starting the installation.

2. Installation must be performed by a qualiﬁed electrician.

1. Can identify day and night: The consumer can adjust working state in dierent ambient light.

It can work in the daytime and at night when it is adjusted on the “sun” position (max). It can

work in the ambient light less than 3LUX when it is adjusted on the “3” position (min). As for the

adjustment pattern, please refer to the testing pattern.

2. Time-Delay is added continually: When it receives the second induction signals within the ﬁrst

induction, it will restart to time from the moment.

As the detector responds to changes in temperature, avoid the following situations

INSTALLATION ADVICE

CONNECTION

• Avoid pointing the detector towards objects with highly reﬂective surfaces,

such as mirrors etc.

• Avoid mounting the detector near heat sources, such as heating vents, air

conditioning units, light etc.

• Avoid pointing the detector towards objects that may move in the wind,

such as curtains, tall plants etc.

• Loosen the screw on the bottom and unload the bottom (refer to the ﬁgure1).

• Pass the power wire through the hole with gasket in the bottom. Connect the power wire into

connection-wire column according to the connection-wire diagram.

• Fix the bottom with inﬂated screw on the selected position (refer to the ﬁgure2).

• Install back the sensor on the buttom, tighten the screw and then test it.

Good Sensitivity Poor Sensitivity

• Turn the LUX knob clockwise on the maximum (sun).Turn the TIME knob anti-clockwise on

the minimum (10s).

• Switch on the power; the sensor and its connected lamp will have no signal at the beginning.

Aer Warm-up 30sec, the sensor can start work .If the sensor receives the induction signal,

the lamp will turn on. While there is no another induction signal any more, the load should

stop working within 10sec±3sec and the lamp would turn o.

• Turn LUX knob anti-clockwise on the minimum (3). If the ambient light is more than 3LUX, the

sensor would not work and the lamp stop working too. If the ambient light is less than 3LUX

(darkness), the sensor would work. Under no induction signal condition, the sensor should

stop working within 10sec±3sec.

CONNECTION-WIRE DIAGRAM

TEST

Figure 1 Figure 2

Note: when testing in daylight, please turn LUX knob to (SUN) position, otherwise the ☼

sensor lamp could not work!

Specyfikacje produktu

Marka:	V-TAC
Kategoria:	detektor ruchu
Model:	VT-80300

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z V-TAC VT-80300, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje detektor ruchu V-TAC

V-TAC VT-8092 Instrukcja

8 Października 2024

V-TAC VT-8091 Instrukcja

8 Października 2024

V-TAC VT-81014 Instrukcja

8 Października 2024

V-TAC VT-81013 Instrukcja

8 Października 2024

V-TAC VT-81012 Instrukcja

8 Października 2024

V-TAC VT-81011 Instrukcja

8 Października 2024

V-TAC VT-81010 Instrukcja

8 Października 2024

V-TAC VT-81009 Instrukcja

8 Października 2024

V-TAC VT-81007 Instrukcja

8 Października 2024

V-TAC VT-80360 Instrukcja

8 Października 2024

Instrukcje detektor ruchu

Najnowsze instrukcje dla detektor ruchu

Maxsa 40234 Instrukcja

9 Października 2024

Maxsa 43218 Instrukcja

9 Października 2024

ORNO OR-CR-233 Instrukcja

9 Października 2024

ORNO OR-CR-219 Instrukcja

9 Października 2024

ORNO OR-CR-232 Instrukcja

9 Października 2024

ORNO OR-CR-231 Instrukcja

9 Października 2024

JUNG BTLC17181244 Instrukcja

8 Października 2024

JUNG BTLC17182250 Instrukcja

8 Października 2024

JUNG BTLC17181255 Instrukcja

8 Października 2024

JUNG BTLC17182259 Instrukcja

8 Października 2024