Instrukcja obsługi TP-Link Omada EAP773

TP-Link Punkt dostępu Omada EAP773

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla TP-Link Omada EAP773 (2 stron) w kategorii Punkt dostępu. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Quick Installation Guide

Wireless Access Point

Note: EAP650 is used as an example throughout the Guide. Images may dier from your actual product.

Hardware Overview

RESET

With the device powered on, press and hold the button for about 5 seconds until the LED flashes quickly. Then

release the button. The device will restore to factory default settings.

Ethernet Port: ETH (PoE)

The port is used to connect to a router or a switch to transmit data, or to a PSE (Power Sourcing Equipment),

such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable.

Note: For EAPs with 10Gbps port, if you use a CAT5E cable, the 10Gbps link of the Ethernet port is less than 55m. To achieve a longer

transmission distance, use a shielded CAT6A cable.

Power Port

Plug one end of the power adapter to this port and the other end to a standard electrical wall outlet to power the

EAP.

Note: Power adapter is not included in the package contents of certain models. For details, refer to the product specications or

datasheet. For power supply specications, refer to the product label.

Self-tapping ScrewsPlastic Wall Anchors

Remove the ceiling tile.

Note: Make sure that the ceiling tile is larger than the EAP.

Wing NutsWashers Pan-head Screws

The EAP can be mounted to the ceiling, the wall, or in a junction box, using the screws in the

package. Choose the appropriate mounting and installation steps below.

Note: This product requires heat dissipation through the metal bracket during use, please be

careful not to touch the metal bracket in the heat dissipation.

Hardware Installation

Insert the plastic wall anchors into the holes.

Front Panel

Rear Panel

Option 1: Ceiling Mounting

Option 2: Wall Mounting

Connect the Ethernet cable to the Ethernet port.

Please pay attention to the triangle sign. Attach

the EAP to the mounting bracket, then rotate it

until it locks into place, as shown on the left.

Place the mounting bracket in the center of the

ceiling tile. Mark positions for the screw holes

and a location for the Ethernet cable hole.

Drill holes for the screws and a hole for the

Ethernet cable at the marked positions.

Secure the mounting bracket to the ceiling tile

using pan-head screws, washers, and wing nuts,

as shown on the left.

Attach the EAP to the mounting bracket by

rotating it until it locks into place, as shown on

the left.

Connect the Ethernet cable to the Ethernet

port on the EAP.

Attach the EAP to the mounting bracket by

rotating it until it locks into place, as shown on

the left.

Setup with videos

Visit https://www.tp-link.com/support/setup-video/ or scan the QR code

to search for the setup video of your product model.

Feed the Ethernet cable through the hole and

set the ceiling tile back into place.

Secure the mounting bracket to the wall by

driving the self-tapping screws into the

anchors. Make sure that the shoulders of the

mounting bracket are on the outside.

If your Ethernet cable feeds through the wall,

position the mounting bracket below the cable

hole. Mark positions for the screw holes and

drill holes at the marked positions.

Φ 7.6 mm (19/64 in)

Option 2: Wall MountingOption 1: Ceiling Mounting Option 3: Junction Box Mounting

Blue On:

Working normally/Initializing. For EAPs with dual-color LED: Normal power supply

Orange On:

For EAPs with dual-color LED: Low power supply

Flash: • Flash twice:

Initialization is completed.

• Flash quickly:

The EAP is resetting, or the Omada controller is locating the device*.

• Flash once per second:

The EAP is upgrading.

• Flash Slowly:

The EAP is in the isolated state.

LED Indicator

Off:

Working abnormally/Power o/LED is turned o.

* When the Locate feature is activated in the Omada controller, the LED ashes quickly to locate and identify the

device. The LED will ash for 10 minutes. You can disable the feature manually to stop it from ashing.

Option 3: Junction Box Mounting

Prepare the cables and the junction box in advance. Ensure that the mounting holes align

to your junction box.

Route the cables through the square cable

hole on the mounting bracket, and secure the

mounting bracket to the junction box using

screws.

The EAP can be powered via a power adapter or a PSE device (such as a PoE switch) which

complies with Power Source Class 2 ( PS2) or Limited Power Source (LPS) of IEC 62368-1.

Option 1: Via PoE Switch

Option 2: Via Power Adapter

Plug one end of the power adapter into the power port of the EAP and the other end to a

standard electrical wall outlet.

Note: Power adapter is not included in the package contents of certain models. For details, refer to the product specications or

datasheet. For power supply specications, refer to the product label.

Power Supply

Switch

Power Adapter

PoE Switch

Connect an Ethernet cable from the PoE switch to the Ethernet port.

Note: For PoE power supply specications, refer to the product label.

*Compatible wall junctions:

Connect the Ethernet cable to the Ethernet

port on the EAP.

Φ 25 mm (63/64 in)

Φ 4 mm (5/32 in)

Method 2: Controller Mode

Note:

• Before you start, be sure to your devices according to the topology figure.power up connect and

• A DHCP server (typically a router with DHCP function enabled) is required to assign IP addresses to

the EAPs and clients in your local network.

Choose a type of Omada Controller:

Choose from the following methods to set up your EAPs:

Method 1: Standalone Mode

Via Omada App

1. Connect your device to the EAP by using the default SSIDs printed on the label at the

bottom of the product.

2. Launch a web browser and enter http://tplinkeap.net in the address bar. Use admin for

both Username and Password to log in.

3. Set up a new Username and Password for secure management purpose. Then you can

configure the AP.

To configure other EAPs, connect your device to each EAP by the corresponding default

SSID and repeat the steps above. You can configure some basic functions in Standalone

Mode. If you want to configure advanced functions, use Controller Mode.

1. Download and install the TP-Link Omada App from App Store or Google Play.

2. Connect your mobile device to the EAP by using the default SSIDs printed on the label

at the bottom of the product.

3. Open the Omada App, go to the >Standalone Devices APs page, and wait for the

EAP to appear. Tap on the EAP to congure it.

The Omada App is designed to help you quickly configure common settings. If you want

to configure advanced settings, use the web page of your EAP or use Controller Mode.

Via Web Browser

Software Conguration

Internet

Clients

Router

EAP

• Method 1: Standalone Mode

To configure and manage EAPs separately (Convenient for a small network with only a few devices)

• Method 2: Controller Mode

To configure and manage EAPs in batches on a central platform, namely Omada Controller.

Note:

• Before you start, be sure to your devices according to the topology figure.power up connect and

• A DHCP server (typically a router with DHCP function enabled) is required to assign IP addresses

to the EAPs and clients in your local network.

Scan for Omada Omada

Switch

Router

Omada Cloud

Clients

EAPEAP EAP EAP

Omada Cloud-Based Controller is a good alternative without the need to install the

software controller on a PC or purchasing the hardware controller.

Licenses need to be purchased additionally.

Type 1: Omada Cloud-Based Controller

* Management via Omada App

After adding a Cloud-Based Controller, you can also manage it via the Omada App.

1. Download and install the TP-Link Omada App from App Store or Google Play.

Scan for Omada Omada

2. Launch the Omada App and log in with your TP-Link ID. Then go to Cloud Access. A list of

controllers that have been bound with your TP-Link ID will appear. Then you can launch

the controller adopt and manage devices.to

1. Contact the sales staff to grant the Omada Cloud-Based Controller permission.

2. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar. Log

in with your TP-Link ID.

3. + Add ControllerClick and add a Cloud-Based Controller. Then you can launch the

controller adopt and manage devices.to

Web Configuration

Switch

Router

Clients

Omada Hardware Controller EAP EAP EAP

Switch

Router

Clients

EAP EAP EAP

Controller

Omada Software Controller

running on the Host PC

Note:

• Before you start, be sure to your devices according to the topology figure.power up connect and

• A DHCP server (typically a router with DHCP function enabled) is required to assign IP addresses to

the EAPs and clients in your local network.

• Omada Controller must have network access to your Omada devices (the router, switch, and EAPs) in

order to find, adopt, and manage them.

Note:

• Before you start, be sure to your devices according to the topology figure.power up connect and

• A DHCP server (typically a router with DHCP function enabled) is required to assign IP addresses

to the EAPs and clients in your local network.

• Omada Controller must have network access to your Omada devices (the router, switch, and

EAPs) in order to find, adopt, and manage them.

• Type 2: Omada Software Controller

On a PC with Windows OS or Linux OS, download the software controller from

https://www.tp-link.com/support/download/omada-software-controller/. Then run the file and

follow the wizard to install and launch the controller.

To manage your devices, the software controller needs to keep running on your computer.

• Type 3: Omada Hardware Controller

If you have no spare PC to keep running the software controller in the network, you can

purchase the hardware controller.

For more details, refer to the Installation Guide of your hardware controller.

Via Omada App

1. Download and install the TP-Link Omada App from App Store or Google Play.

2. Launch your Omada App and configure the controller at a local site or remote site.

• Local Management

a. Connect your mobile device to the EAP by using the default SSIDs printed on the

label at the bottom of the product.

b. Launch the Omada App and go to Local Access, tap the + button on the upper-right

corner to add the controller. Then you can launch the controller to adopt and manage

devices.

• Remote Management

Note: Before you start, make sure that both your controller and mobile device can access the

internet.

a. Make sure that Cloud Access is enabled on your controller and your controller has

been bound with your TP-Link ID.

b. Launch Omada App and log in with your TP-Link ID. Then go to Cloud Access. A list

of controllers that have been bound with your TP-Link ID will appear. Then you can

launch the controller adopt and manage devices.to

Scan for Omada Omada

Via Omada App

1. Download and install the TP-Link Omada App from App Store or Google Play.

2. Launch your Omada App and configure the controller at a local site or remote site.

• Local Management

a. Connect your mobile device to the EAP by using the default SSIDs printed on the

label at the bottom of the product.

b. Launch the Omada App and go to Local Access, tap the + button on the

upper-right corner to add the controller. Then you can launch the controller to

adopt and manage devices.

• Remote Management

Note: Before you start, make sure that both your controller and mobile device can access the

internet.

a. Make sure that Cloud Access is enabled on your controller. By default, Cloud

Access is enabled. Make sure that the Cloud LED is flashing slowly.

b. Launch Omada App and log in with your TP-Link ID. Then go to Cloud Access. Tap

the + button on the upper-right to add your controller. Then you can launch the

controller adopt and manage devices.to

Scan for Omada Omada

1. Open the controller’s web page.

Launch the software controller on your PC. After the initiation process, the controller

automatically opens its web page. If not, click Launch a Browser to Manage the Network.

2. On the controller’s web page, follow the wizard to complete the quick setup. Then you can

launch the controller adopt and manage devices.to

3. (For Remote Management) You can remotely access and manage your controller via

Omada Cloud Service.

Note: Before you start, make sure that both your controller and PC can access the internet.

a. Make sure that Cloud Access is enabled on your controller and your controller has

been bound with your TP-Link ID. On the controller’s web page, go to Settings > Cloud

Access to enable Cloud Access and bind your TP-Link ID. If you have set it up in the

quick setup, skip this step.

b. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar.

Enter your TP-Link ID and password to log in. A list of controllers that have been bound

with your TP-Link ID will appear. Then you can launch the controller to adopt and

manage devices.

Via Web Browser

1. Open the controller’s web page.

Find the IP address of the controller on the gateway router’s DHCP client list. Enter the

IP address in the address bar to open its web page.

2. On the controller’s web page, follow the wizard to complete the quick setup. Then you

can launch the controller adopt and manage devices.to

3. (For Remote Management) You can remotely access and manage your controller via

Omada Cloud Service.

Note: Before you start, make sure that both your controller and PC can access the internet.

a. Make sure that Cloud Access is enabled on your controller. By default, Cloud

Access is enabled. Make sure that the Cloud LED is flashing slowly.

b. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar.

Enter your TP-Link ID and password to log in. Click + Add Controller and choose

Hardware Controller to add your controller. Then you can further configure the

controller.

Via Web Browser

Safety Information

• Keep the device away from water, re, humidity or hot environments.

• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

• Do not use the device where wireless devices are not allowed.

• Do not use damaged charger or USB cable to charge the device.

• Do not use any other chargers than those recommended.

• Adapter shall be installed near the equipment and shall be easily accessible.

For the detailed configurations, refer to the User Guide of the controller and EAPs. The guides can

be found on the download center of our official website: https://www.tp-link.com/support/download/.

For technical support, the user guide and other information,

please visit https://www.tp-link.com/support, or simply scan the QR code.

To ask questions, find answers, and communicate with TP-Link users or engineers,

please visit https://community.tp-link.com to join TP-Link Community.

https://omada.tplinkcloud.com

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of

directives 2014/53/EU, 2009/125/EC, 2011 /65/EU and (EU) 2015/863.

The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of

the Radio Equipment Regulations 2017.

The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca/

Specyfikacje produktu

Marka:	TP-Link
Kategoria:	Punkt dostępu
Model:	Omada EAP773

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z TP-Link Omada EAP773, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Punkt dostępu TP-Link

TP-Link Festa F65-Wall Instrukcja

9 Października 2024

TP-Link Festa F65 Instrukcja

5 Października 2024

TP-Link TL-WPA1000 Instrukcja

3 Października 2024

TP-Link Omada EAP773 Instrukcja

3 Października 2024

TP-Link EAP110-Outdoor V3 Instrukcja

1 Października 2024

TP-Link TL-WA1801 Instrukcja

28 Września 2024

TP-Link Omada EAP610-Outdoor Instrukcja

28 Września 2024

TP-Link Omada Pro AP7650 Instrukcja

27 Września 2024

TP-Link Omada Pro AP9650 Instrukcja

25 Września 2024

TP-Link Omada Pro AP9635 Instrukcja

25 Września 2024

Instrukcje Punkt dostępu

Najnowsze instrukcje dla Punkt dostępu

Cisco MR12 Instrukcja

14 Października 2024

Draytek VigorAP 920R Instrukcja

13 Października 2024

Netgear WNDAP360 Instrukcja

12 Października 2024

D-Link DWL-1000AP+ Instrukcja

9 Października 2024

D-Link DWL-700AP Instrukcja

9 Października 2024

Cambium Networks cnPilot e505 Instrukcja

9 Października 2024

Cambium Networks cnPilot e425H Instrukcja

9 Października 2024

Cambium Networks cnPilot e600 Instrukcja

9 Października 2024

Cambium Networks cnPilot e510 Instrukcja

9 Października 2024

Cambium Networks cnPilot e502S Instrukcja

9 Października 2024