Instrukcja obsługi Star Micronics TSP143IIIW

Star Micronics drukarka TSP143IIIW

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Star Micronics TSP143IIIW (36 stron) w kategorii drukarka. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/36

TSP100LAN

Hardware Manual

Trademark acknowledgments

TSP100LAN: Star Micronics Co., Ltd.

Notice

permission is forbidden.

• e contents of this manual are subject to change without notice.

• All eorts have been made to ensure the accuracy of the contents of this manual at the time of going to press.

However, should any errors be detected, STAR would greatly appreciate being informed of them.

• e above notwithstanding, STAR can assume no responsibility for any errors in this manual.

2010-2013 Star Micronics Co., Ltd.

Federal Communications Commission

Radio Frequency Interference

Statement

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) is device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

NOTE: is equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. ese limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. is equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

is statement will be applied only for the printers marketed in U.S.A.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.

For RF interference suppression, if a ferrite core is provided with this device, ax it to the interface cable

Statement of

e Canadian Department of Communications

Radio Interference Regulationst

is Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

e above statement applies only to printers marketed in Canada.

Please access the following URL

http://www.star-m.jp/eng/dl/dl02.htm

for the latest revision of the manual.

TABLE OF CONTENTS

1. Unpacking and Installation 1 ...................................................................................................................

1-1. Unpacking ................................................................................................................................................ 1

1-2. Choosing a place for the printer 2 ...........................................................................................................

2. Parts Identication and Nomenclature 3 ................................................................................................

3. Setup 4 ......................................................................................................................................................

3-1. Connecting the Ethernet Cable to the Printer 4 ....................................................................................

3-2. Connecting to a Peripheral Unit 5 ...........................................................................................................

3-3. Loading the Paper Roll 6 ...........................................................................................................................

3-4. Connecting the Ethernet Cable to the PC 10 .........................................................................................

3-5. Connecting the Power Cord 11 ................................................................................................................

3-6. Turning Power On 12 ................................................................................................................................

4. Attaching the Accessories 13 ....................................................................................................................

4-1. Attaching the Holder Plate 13 ..................................................................................................................

4-2. Attaching the Rubber Feet 15 ...................................................................................................................

4-3. Switch Cover Installation 16 .....................................................................................................................

5. ermal Roll Paper Specication 17 ........................................................................................................

5-1. Roll paper specication 17 ........................................................................................................................

5-2. Recommended paper 17 ...........................................................................................................................

6. Control Panel and Other Functions 18 ....................................................................................................

6-1. Control Panel 18 .........................................................................................................................................

6-2. Errors ......................................................................................................................................................18

6-3. Self-Printing .......................................................................................................................................... 20

7. Preventing and Clearing Paper Jams 21 ..................................................................................................

7-1. Preventing Paper Jams 21 .........................................................................................................................

7-2. Removing Paper Jam 21 ............................................................................................................................

7-3. Releasing a Locked Cutter (Auto Cutter Mode only) 22 ......................................................................

8. Periodical Cleaning 24 .............................................................................................................................

8-1. Cleaning the ermal Head 24 ................................................................................................................

8-2. Cleaning the Rubber Roller 24 .................................................................................................................

8-3. Cleaning the Paper Holder and the Surrounding Area 24 ...................................................................

9. Peripheral Unit Drive Circuit 25 .............................................................................................................

10. Specications 27 .....................................................................................................................................

10-1. General Specications 27 ..........................................................................................................................

10-2. Auto Cutter Specications 28 ...................................................................................................................

10-3. Ethernet Interface 28 .................................................................................................................................

10-4. Electrical Characteristics 28 .....................................................................................................................

10-5. Environmental Requirements 29 .............................................................................................................

10-6. Reliability ............................................................................................................................................... 30

11. DIP Switch Settings 31 ...........................................................................................................................