Instrukcja obsługi Star Micronics TSP143IIIU

Star Micronics drukarka TSP143IIIU

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Star Micronics TSP143IIIU (30 stron) w kategorii drukarka. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/30

Hardware Manual

Model: TSP143IIU

Federal Communications Commission Radio Frequency Interference Statement

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) is device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.

For RF interference suppression, if a ferrite core is provided with this device, ax it to the interface cable

NOTE:

is equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. is equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

CAN ICES-3 (A) / NMB-3 (A)

Trademark acknowledgments

TSP100II: Star Micronics Co., Ltd.

Notice

permission is forbidden.

• e contents of this manual are subject to change without notice.

• All eorts have been made to ensure the accuracy of the contents of this manual at the time of going to press.

However, should any errors be detected, STAR would greatly appreciate being informed of them.

• e above notwithstanding, STAR can assume no responsibility for any errors in this manual.

2010-2017 Star Micronics Co., Ltd..

EMI Class A Warning

http://www.starmicronics.com/support/mannualfolder/ClassA_Warning.pdf

Please access the following URL

http://www.starmicronics.com/support/

for the latest revision of the manual.

TABLE OF CONTENTS

1. Unpacking and Installation 1 .....................................................................................................................

1-1. Unpacking ....................................................................................................................................1

1-2. Choosing a place for the printer 2 ...................................................................................................

1-3. Nomenclature ...............................................................................................................................3

2. Product Features 4 ......................................................................................................................................

2-1. Product Features 4 ...........................................................................................................................

2-2. Operation Modes 4 ..........................................................................................................................

3. Setup 5 ..........................................................................................................................................................

3-1. Connecting the Power Cord 5 .........................................................................................................

3-2. Connecting the USB Cable to the Printer 6 ....................................................................................

3-3. Connecting to a Peripheral Unit 7 ...................................................................................................

3-4. Turning Power On and Power Off................................................................................................8

3-5. Loading the Paper Roll 10 ..............................................................................................................

4. Attaching the Accessories ......................................................................................................................14

4-1. Attaching the Upper Guide 14 ........................................................................................................

4-2. Attaching the Holder Plate 15 .........................................................................................................

4-3. Attaching the Rubber Feet 17 .........................................................................................................

5. Thermal Roll Paper Speciﬁcation 18 .........................................................................................................

5-1. Compliant Paper Roll Speciﬁcations 18 .........................................................................................

6. Control Panel and Other Functions 19 .....................................................................................................

6-1. Control Panel..............................................................................................................................19

6-2. Lamp Indicator 19 ...........................................................................................................................

6-3. Self-Printing ...............................................................................................................................21

7. Preventing and Clearing Paper Jams 22 ...................................................................................................

7-1. Preventing Paper Jams 22 ...............................................................................................................

7-2. Removing Paper Jam 22 .................................................................................................................

7-3. Releasing a Locked Cutter 24 ........................................................................................................

8. Periodical Cleaning 26 ................................................................................................................................