Instrukcja obsługi Star Micronics mC-Print3
Star Micronics
drukarka
mC-Print3
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Star Micronics mC-Print3 (3 stron) w kategorii drukarka. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/3
3-A Connecting an Android terminal to the printer
Check the Supplied Accessories If any of the package contents are missing or damaged, contact the dealer where the
product was purchased. * Accessories vary depending on the region where the printer was purchased.
This document explains the procedures for use of mC-Print3. Please store it carefully after reading it.
Introduction
Paper Roll
Guide
Paper Roll Easy
Setup Guide
Safety
Instructions
This Manual
Power Cable*AC Adapter Flyer
(Q&A reference)
What the utility can do
The utility can be used to change the settings of the printer and peripheral devices.
Examples) • LAN settings • Memory switch changes, logo registration
• Sample printing • Checking if connected device supports USB PD (Power Delivery)
• Firmware update/diagnosis etc.
● To use the utility, download it from the site at right.
● To perform setup using this manual, proceed to Step 1.
www.star-m.jp/mcprint3-oml.html
mC-Print3 Online Manual
In Case of Trouble
If you experience trouble with the setup procedure, refer to the Online Manual.
Place the enclosed yer close to the printer and use it when necessary.
MCP31C
Easy Setup Guide
www.star-m.jp/mcprint-app.html
mC-Print3 Utility Download
1
Installing the paper roll
Take the slack of the paper roll before paper
setting, insert the paper roll as shown in the
illustration.
Pull the end of the paper roll out straight ,
and use both hands to close the printer cover
.
3
4
4
2
1
Pull the open lever and open the printer
cover .
When using a 58 mm roll, install the pro-
vided paper roll guide.
B
A
1
2
With the notch part A (triangle mark) of the
paper roll guide facing down, angle the guide
to the right and insert it .
Position so that the notch part A is aligned
with the main unit rib B, then slide the guide
from the right .
When the slid paper roll guide stops, stand
it up vertical , and press until it clicks into
place .
To change the paper width, it is necessary
to change the memory switch setting. For
details, refer to the Online Manual.
3
4
2
Turning ON the main unit power
Press the power button and conrm that
the LED (blue) illuminates .
4
5
Connect the power cable to the AC adapter
, and connect the cable connector to the
printer as shown in the illustration . Insert
the plug into the outlet .
Place your nails into the gaps in the right and
left sides of the rear cover on the back of the
printer, and then remove the cover.
RESET
RESET
DC24V
LAN Cash Drawer
/Buzzer
0.5A 0.5A
iPa d
18W(USB PD)
1
3
2
USB Cable
（C-C)
80878690
Connect the LAN cable to the printer LAN connector .
RESET
DC
24V
LAN
Cash Drawer
/Buzzer
0.5A 0.5A
d
18W(USB PD)
LAN
1
2
Connect the other plug to the connector of the router, hub, or other
LAN device .
Wired LAN interface
You will need:
• Commercially-available LAN cable
Printer-side plug
DHCP is enabled by default for the wired LAN settings. To
continually use the same IP address, set a static IP address
before use.
For the static IP address setting procedure, refer to the On-
line Manual.
USB interface
Connect the USB cable to the printer USB-C® connector
.
You will need:
• USB cable (C-C)
provided with the printer
2
Printer-side plug
Connect the other plug to the smartphone/tablet .
RESET
DC
24V
LAN
Cash Drawer
/Buzzer
0 A
iP ad
18W(USB
1
Connecting a Tablet or PC to the Printer
Installing the Printer
If your Android device cannot connect to the printer, it may
not support USB PD (Power Delivery).
Follow the procedure below and switch the USB-C function
to “Data only”.
Switching the USB-C function manually (For using the USB interface)
If the communication connection is not successful, follow the procedure
below and switch the USB-C function.
Turn on the printer power.
Pull the open lever, and then open the printer cover.
Press the FEED button for 5 seconds (LED red ashes).
Press and release the FEED button to select the USB-C function.
Close the printer cover, and then save the selected function in step
.
➏ Check the status of the saved function on the test printing.
LED USB-C function Description of test printing
Red ashing Data only USB-C: Data Only
Blue ashing Power supply only USB-C: Power Supply Only
Purple ashing Power supply
and data USB-C: Power Supply / Data
6
2
1
35 seconds
Press
and release
4
5
◦ IOS is a trademark or registered trademark of Cisco Systems, Inc. in the United States and other countries, and is used based on a license. ◦ Android is a trademark of Google Inc.
◦ Windows is a registered trademark of the U.S. Microsoft Corporation in the United States, Japan, and other countries. ◦ Mac is a trademark of Apple Inc., registered in the U.S. and
other countries. ◦ USB Type-C®and USB-C®are registered trademarks of USB Implementers Forum. ◦ For more details, refer to our company’s FAQ site (http://www.star-m.jp/faq/
index.html).
3-D Connecting the iOS device and the printer via wired LAN
Copyright 2020 Star Micronics Co., Ltd.
Press the hooks A at the bottom of the rear cover into the
notches in the printer main unit , then t the hooks B on the
left and right of the rear cover into the printer main unit until they
click into place .
A
B
B
1
2
www.star-m.jp/mac-cps.html
● Download the Mac CUPS
driver
Download the Mac CUPS driver or Linux CUPS driver.
For details, refer to the Online Manual.
www.star-m.jp/linux-cps.html
● Download the Linux CUPS
driver
3-C Connecting a Mac/Linux terminal to the printer
3-B Connecting a Windows tablet or PC terminal to the printer
Connect the LAN cable to the printer LAN connector .
RESET DC
24V
LAN
Cash Drawer
/Buzzer
0.5A 0.5A
d
18W(USB PD)
LAN
1
2
Connect the other plug to the connector of the router, hub, or other
LAN device .
Wired LAN interface
You will need:
• Commercially-available LAN cable
Printer side Plug
Connect the USB cable to the printer USB-C connector .
USB interface
Printer-side plug
2
Be sure to install the Windows driver before connecting the USB
cable.
Connect the other plug to the connector of the Windows tablet/PC
.
DHCP is enabled by default for the wired LAN settings. To
continually use the same IP address, set a static IP address
before use.
For the static IP address setting procedure, refer to the On-
line Manual.
RESET
DC
24V
LAN
Cash Drawer
/Buzzer
0 A
iPa d
18W(USB
1
www.star-m.jp/mcprint-wsw.html
Download the StarPRNT for
mCollection Windows driver
Installing the Windows driver
Download [mCollection Printer Software].
Extract the downloaded software and execute “Setup.exe”.
Follow the wizard instructions and complete software installation.
The Windows driver is included in the mCollection Printer Software.
The mCollection Printer Software can be used to congure the printer
settings and perform an operation test.
You will need:
• USB cable (C-C)
provided with the printer
If your Windows device cannot connect to the print-
er, it may not support USB PD (Power Delivery).
Refer to “Switching the USB-C function manually” on the
front page of this manual, and then switch the function to
“Data only”.
Connect the LAN cable to the printer LAN connector
.
RESET
DC
24V
LAN
Cash Drawer
/Buzzer
0.5A 0.5A
d
18W(USB PD)
LAN
1
2
Connect the other plug to the connector of the router, hub, or other
LAN device .
Wired LAN interface
USB connection with iOS devices is not supported.
Printer-side plug
Image of connection
You will need:
• Commercially-available LAN cable
DHCP is enabled by default for the wired LAN settings.
To continually use the same IP address, set a static IP
address before use.
For the static IP address setting procedure, refer to the
Online Manual.
Installing the rear cover
Initializing the communication settings (For Wired LAN Interface)
RESET
LAN
4
3
1
2
If the communication connection is not successful, follow the
procedure below and initialize the communication setting.
After initialization, perform connection again starting from the
beginning of 3-A, B, or D.
<Procedure>
Check that the printer power is OFF.
Insert a pen with a small tip or similar item and press the RESET button
on the back
.
At the same time, press the power switch on the front of the printer
until the POWER LED turns on (power ON)
.
Keep pressing RESET switch until the Network LED (green) on the front
of the printer ashes .
Press and hold the FEED button to conrm.
Installing the rear cover onto the back of the printer
Specyfikacje produktu
| Marka: | Star Micronics |
| Kategoria: | drukarka |
| Model: | mC-Print3 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Star Micronics mC-Print3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje drukarka Star Micronics
7 Października 2024
7 Października 2024
22 Września 2024
16 Września 2024
15 Września 2024
15 Września 2024
15 Września 2024
14 Września 2024
13 Września 2024
12 Września 2024
Instrukcje drukarka
- drukarka Sony
- drukarka Samsung
- drukarka LG
- drukarka Xiaomi
- drukarka Sharp
- drukarka Huawei
- drukarka Lenovo
- drukarka Epson
- drukarka Fujitsu
- drukarka Roland
- drukarka Panasonic
- drukarka StarTech.com
- drukarka Canon
- drukarka Fujifilm
- drukarka Toshiba
- drukarka D-Link
- drukarka Citizen
- drukarka HP
- drukarka Brother
- drukarka Honeywell
- drukarka Kodak
- drukarka Primera
- drukarka Xerox
- drukarka Godex
- drukarka Olivetti
- drukarka Zebra
- drukarka Dell
- drukarka Digitus
- drukarka Kyocera
- drukarka Ricoh
- drukarka Seiko
- drukarka Renkforce
- drukarka Thomson
- drukarka Panduit
- drukarka Olympus
- drukarka OKI
- drukarka Mitsubishi
- drukarka Intermec
- drukarka NEC
- drukarka Polaroid
- drukarka Konica Minolta
- drukarka Bixolon
- drukarka Pantum
- drukarka Olympia
- drukarka Datamax O'Neil
- drukarka DNP
- drukarka Equip
- drukarka TSC
- drukarka HiTi
- drukarka Triumph-Adler
- drukarka Fargo
- drukarka Entrust
- drukarka Brady
- drukarka Lexmark
- drukarka Sagem
- drukarka Nilox
- drukarka Argox
- drukarka Royal Sovereign
- drukarka Minolta
- drukarka Oce
- drukarka Paxar
- drukarka IDP
- drukarka Metapace
- drukarka Ultimaker
- drukarka Toshiba TEC
- drukarka Frama
- drukarka Kogan
- drukarka Posiflex
- drukarka Dascom
- drukarka GG Image
- drukarka Vupoint Solutions
- drukarka Elite Screens
- drukarka DTRONIC
- drukarka Phoenix Contact
- drukarka Epson 7620
- drukarka Star
- drukarka EC Line
- drukarka Colop
- drukarka Approx
- drukarka Fichero
- drukarka Raspberry Pi
- drukarka Evolis
- drukarka Tally Dascom
- drukarka Custom
- drukarka Nisca
Najnowsze instrukcje dla drukarka
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
14 Października 2024
14 Października 2024
13 Października 2024
13 Października 2024
13 Października 2024