Instrukcja obsługi Satel INT-KWRL2

Satel detektor INT-KWRL2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Satel INT-KWRL2 (16 stron) w kategorii detektor. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/16
INT-KWRL2
Wireless keypad
Firmware version 3 int-kwrl2_ 03/ .00 en 21
SATEL sp. z o.o. ul. Budowlanych 66 - POLAND 80 298 Gdańsk •
tel. +48 58 320 94 00
www.satel. eu
IMPORTANT
The device should be installed by qualied personnel.
Read carefully this manual before proceeding to installation.
Changes, modications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
The name plate of the device is located on the enclosure base.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
https://support.satel.eu
Hereby, SATEL sp. z o.o. declares that the radio equipment type INT-KWRL2 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: www.satel.eu/ce
In the EU, th radio equipment is only permitted to operate in the 868 MHz frequency is
band.
The following symbols may be used in this manual:
- note,
- caution.
The INT-KWRL2 wireless keypad enables operation and programming of the INTEGRA and
INTEGRA Plus control panels with firmware version 1.19 (or newer). The device is designed
for work within the ABAX 2 / ABAX two-way wireless system. This manual applies to the
keypad with rmware version 3.00 (or newer), which is supported by:
2: ACU-220 / ACU-280 controller, ABAX
ABAX: ACU-120 / ACU-270 controller (rmware version 5.04 or newer).
The ABAX 2 / ABAX controller must be connected to the expander bus (controller
terminals CKE and DTE) and the keypad bus (controller terminals CKM and DTM)
of the INTEGRA / INTEGRA Plus alarm control panel.
In the ACU-220 / ACU-280 controller, switches 9 and 10 must be set in OFF position.
In the ACU-120 / ACU-270 controller, switch 8 must be set in OFF position.
The keypad is not supported by the ARU-100 and ARU-200 radio signal repeaters or
by the INTEGRA 128-WRL control panel.
Fig. 1. INT-KWRL2 keypad.


Specyfikacje produktu

Marka: Satel
Kategoria: detektor
Model: INT-KWRL2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Satel INT-KWRL2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje detektor Satel

Satel

Satel ACU-120 Instrukcja

20 Września 2024
Satel

Satel MAGENTA Instrukcja

20 Września 2024
Satel

Satel ACX-210 Instrukcja

18 Września 2024
Satel

Satel FD-1 Instrukcja

18 Września 2024
Satel

Satel INT-KWRL2 Instrukcja

18 Września 2024
Satel

Satel ETHM-1 Plus Instrukcja

18 Września 2024
Satel

Satel INT-E Instrukcja

17 Września 2024

Instrukcje detektor

Najnowsze instrukcje dla detektor