Instrukcja obsługi RIKON 10-3061

RIKON Maszyna do piłowania 10-3061

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla RIKON 10-3061 (32 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/32

www.rikontools.com

10-3061M4

10″ Deluxe Bandsaw

Operator’s Manual

Record the serial number and date of purchase in your manual for future reference.

The serial number can be found on the specication label on the rear of your machine.

Serial Number: _________________________ Date of purchase: _________________________

For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877) 884-5167

Specications.....................................................................................................................2

Safety Instructions ........................................................................................................3 - 6

Getting To Know Your Machine .........................................................................................7

Contents of Package ............................................................................................................8 - 9

Installation ................................................................................................................9

Assembly .........................................................................................................................10 - 12

Adjustments...............................................................................................................12 - 19

Operation ..................................................................................................................20

Maintenance ....................................................................................................................20

Wiring Diagram ................................................................................................................21

Troubleshooting ........................................................................................................21 - 23

Parts Diagrams & Parts Lists ..................................................................................24 - 27

Notes ...............................................................................................................................28

Accessories .............................................................................................................................29

‘How To’ Guide for all Band Saw Blades ................................................................................30

Warranty ..........................................................................................................................31

TABLE OF CONTENTS

SPECIFICATIONS #10-3061

NOTE: The specications, photographs, drawings and information in this manual represent the current model when the

manual was prepared. Changes and improvements may be made at any time, with no obligation on the part of Rikon

Power Tools, Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in

this manual is correct, to provide you with the guidelines for the proper safety, assembly and operation of this machine.

Motor ............................................................................................... 1/2 HP, TEFC

Motor Speed (no load)......................................................................... 1,720 RPM

Volts ............................................................................................................ 115 V

Amps, Hertz, Phase .................................................................. 5.5 A, 60 Hz, 1Ph

Blade Length .......................................................................... 70-1/2” (1,791 mm)

Blade Width ............................................................. 1/8” - 1/2” (3.18 - 12.7 mm**

Blade Speed ........................................... 1,515 / 3,280 ft/min (462 / 1,000 m/min)

Table Size (W x D) ............................................ 13-3/4” x 12-1/2” (350 x 320 mm)

Table Tilt ................................................................................... Left -5

0 , Right 45°

Miter Gauge Slots (1) ..................................................... 5/8” x 1/4” (16 x 6.5 mm)

Maximum Cutting Width (throat) ............................................... 9-5/8” (244.5 mm)

Maximum Cutting Depth (height) ....................................................... 5” (127 mm)

Table Height to Base ................................................................. 14-1/2” (368 mm)

Fence Height ................................................................................. 2-3/8” (60 mm)

Fence Length ............................................................................ 12-1/4’” (310 mm)

Dust Ports (1) ............................................... 2-1/2” O.D. / 2-1/4” I.D (64 / 57 mm)

Base Size (WxD) ................................................ 15-7/8” x 9-3/8” (403 x 238 mm)

Overall Height ............................................................................ 34-1/4” (870 mm)

Overall Width x Depth.............................................. 21” x 16-1/4” (534 x 413 mm)

Net Weight .............................................................................. 77.5 lbs. (35.14 kg)

1/8” (3.18mm) bandsaw blades should be 0.018” to 0.020” gauge to reduce tracking issues common with this width. *

SAFETY SYMBOLS

IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following

instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock,

re, and/or serious personal injury.

There are certain applications for which this tool was designed. We strongly recommend that this tool not be modied

and/or used for any other application other than that for which it was designed. If you have any questions about its

application, do not use the tool until you have contacted us and we have advised you.

SAFETY INSTRUCTIONS

GENERAL SAFETY

KNOW YOUR POWER TOOL. Read the owner’s manual

carefully. Learn the tool’s applications, work capabilities,

and its specic potential hazards.

BEFORE USING YOUR MACHINE

To avoid serious injury and damage to the tool, read and

follow all of the Safety and Operating Instructions before

operating the machine.

1. California Proposition 65 Warning: Some dust cre-

ated by power sanding, sawing, grinding, drilling and other

construction activities contains chemicals known to the

State of California to cause cancer, birth defects, or other

reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement, and other

• Masonry products.

• Arsenic and chromium from chemically treated lumber.

Your risk from exposure to these chemicals varies, depend-

ing on how often you do this type of work. To reduce your

exposure, work in a well ventilated area and work with

approved safety equipment, such as dust masks that are

specially designed to lter out microscopic particles.

2. the entire Owner’s Manual. how to use READ LEARN

the tool for its intended applications.

3. GROUND ALL TOOLS. If the tool is supplied with a 3

prong plug, it must be plugged into a 3-contact electrical

receptacle. The 3rd prong is used to ground the tool and

provide protection against accidental electric shock. DO

NOT remove the 3rd prong. See Grounding Instructions

on the following pages.

4. AVOID A DANGEROUS WORKING ENVIRONMENT.

DO NOT use electrical tools in a damp environment or

expose them to rain.

5. use electrical tools in the presence of DO NOT

ammable liquids or gasses.

6. ALWAYS keep the work area clean, well lit, and

organized. work in an environment with oor DO NOT

surfaces that are slippery from debris, grease, and wax.

7. KEEP VISITORS AND CHILDREN AWAY. DO NOT

permit people to be in the immediate work area,

especially when the electrical tool is operating.

8. to perform an operation DO NOT FORCE THE TOOL

for which it was not designed. It will do a safer and

higher quality job by only performing operations for

which the tool was intended.

9. wear loose WEAR PROPER CLOTHING. DO NOT

clothing, gloves, neckties, or jewelry. These items can

get caught in the machine during operations and pull the

operator into the moving parts. The user must wear a

protective cover on their hair, if the hair is long, to

prevent it from contacting any moving parts.

10. CHILDPROOF THE WORKSHOP AREA by

removing switch keys, unplugging tools from the

electrical receptacles, and using padlocks.

11. ALWAYS UNPLUG THE TOOL FROM THE

ELECTRICAL RECEPTACLE when making adjust-

ments, changing parts or performing any maintenance.

SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION. This symbol may be used

in conjunction with other symbols or pictographs.

Indicates an imminently hazardous situation, which, if not avoided, could result in death or

serious injury.

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious

injury.

Indicates a potentially hazardous situation, which, if not avoided, could result in minor or

moderate injury.

NOTICE: Shown without Safety Alert Symbol indicates a situation that may result in property damage.

Specyfikacje produktu

Marka:	RIKON
Kategoria:	Maszyna do piłowania
Model:	10-3061

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z RIKON 10-3061, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Maszyna do piłowania RIKON

RIKON 10-600VS Instrukcja

27 Grudnia 2024

RIKON 10-353 Instrukcja

27 Grudnia 2024

RIKON 10-342 Instrukcja

27 Grudnia 2024

RIKON 10-205 Instrukcja

27 Grudnia 2024

RIKON 11-600S Instrukcja

27 Grudnia 2024

RIKON 10-3061 Instrukcja

27 Grudnia 2024

RIKON 10-347 Instrukcja

27 Grudnia 2024

RIKON 10-305 Instrukcja

27 Grudnia 2024

RIKON 10-110 Instrukcja

3 Października 2024

RIKON 10-306 Instrukcja

3 Października 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

MSW -TSAW2000EXT Instrukcja

31 Grudnia 2025

Trotec PJSS 10-20V Instrukcja

30 Grudnia 2025

Stihl MS 201 TC-M Instrukcja

30 Grudnia 2025

Black Decker 3157 Instrukcja

30 Grudnia 2025

Silverline 624327 Instrukcja

30 Grudnia 2025

Bavaria BEC 1835 Instrukcja

30 Grudnia 2025

Sun Joe SWJ802E-PRP Instrukcja

30 Grudnia 2025

Sun Joe 20VIONLTE-CS10-RM Instrukcja

30 Grudnia 2025

AL-KO C50 Li Instrukcja

30 Grudnia 2025

Spear & Jackson SPJCS 1840 Instrukcja

29 Grudnia 2024