Instrukcja obsługi RIKON 10-110

RIKON Maszyna do piłowania 10-110

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla RIKON 10-110 (27 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/27
10” Cabinet Saw
Sliding Table Model: 10-110
Cast Table Wings Model: 10-050
Owner’s Manual
For more information:
www.rikontools.com info@rikontools.com or
For Parts or Questions:
techsupport@rikontools.com 877-884-5167or
Record the serial number and date of purchase
in your manual for future reference.
Serial number:
Date of purchase:
Part #10-110M2
IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following in-
structions must be followed at all times.
There are certain applications for which this tool was designed. We strongly recommend that this tool not be modifi ed and/or
used for any other application other than that for which it was designed. If you have any questions about its application, do not
use the tool until you have contacted us and we have advised you.
KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s applications, work capabilities, and its
specifi c potential hazards.
ALWAYS KEEP VISITORS AWAY FROM RUNNING MACHINES.
All visitors should be kept a safe distance from the work area.
ALWAYS MAKE THE WORKSHOP CHILDPROOF.
Childproof with padlocks, master switches, or by removing starter keys.
NEVER OPERATE A TOOL WHILE UNDER THE INFLUENCE OF DRUGS, MEDICATION, OR ALCOHOL.
ALWAYS WEAR PROPER APPAREL.
Never wear loose clothing or jewelry that might get caught in moving parts. Rubber-soled footwear is
recommended for the best footing.
ALWAYS USE SAFETY GLASSES AND WEAR HEARING PROTECTION.
NEVER OVERREACH.
Keep your proper footing and balance at all times.
ALWAYS GROUND ALL TOOLS.
If your tool is equipped with a three-pronged plug, you must plug it into a three-hole electric receptacle.
If you use an adapter to accommodate a two-pronged receptacle, you must attach the adapter plug to a
known ground. Never remove the third prong of the plug.
ALWAYS AVOID DANGEROUS ENVIRONMENTS.
Never use power tools in damp or wet locations. Keep your work area well lighted and clear of clutter.
ALWAYS REMOVE THE ADJUSTING KEYS AND WRENCHES FROM TOOLS AFTER USE.
Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning
it on.
ALWAYS KEEP YOUR WORK AREA CLEAN. Cluttered areas and benches invite accidents.
NEVER STAND ON TOOLS.
Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.
2
Operator Safety: Required Reading
General Safety Warnings
ALWAYS CHECK FOR DAMAGED PARTS.
Before initial or continual use of the tool, a guard or other part that is damaged should be checked to assure
that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or
other damaged parts should immediately be properly repaired or replaced.
ALWAYS DISCONNECT TOOLS.
Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters.
ALWAYS AVOID ACCIDENTAL STARTING.
Make sure switch is in “OFF” position before plugging in cord.
NEVER LEAVE TOOLS RUNNING UNATTENDED.
1. Always wear eye protection.
2. Keep hands away from the saw blade while machine is running.
3. Always use blade guard during normal cutting operations.
4. Always use splitter during normal cutting operations.
5. Use push sticks when ripping narrow stock.
6. Always use fence while ripping and miter gauge while cross-cutting.
7. Never reach over or behind saw blade while machine is running.
8. Do not remove cut-off or jammed pieces until blade has come to a full stop.
9. Disconnect machine from power source before making repairs or adjustments.
10. Do not expose saw or power cord to water or use in damp locations.
SAVE THESE INSTRUCTIONS.
Refer to them often.
3
Table Saw Safety Rules

Specyfikacje produktu

Marka: RIKON
Kategoria: Maszyna do piłowania
Model: 10-110

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z RIKON 10-110, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Maszyna do piłowania RIKON

RIKON

RIKON 10-600VS Instrukcja

27 Grudnia 2024
RIKON

RIKON 10-353 Instrukcja

27 Grudnia 2024
RIKON

RIKON 10-342 Instrukcja

27 Grudnia 2024
RIKON

RIKON 10-205 Instrukcja

27 Grudnia 2024
RIKON

RIKON 11-600S Instrukcja

27 Grudnia 2024
RIKON

RIKON 10-3061 Instrukcja

27 Grudnia 2024
RIKON

RIKON 10-347 Instrukcja

27 Grudnia 2024
RIKON

RIKON 10-305 Instrukcja

27 Grudnia 2024
RIKON

RIKON 10-110 Instrukcja

3 Października 2024
RIKON

RIKON 10-306 Instrukcja

3 Października 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Husqvarna

Husqvarna 455e Rancher Instrukcja

12 Stycznia 2025
Güde

Güde GSS 400 Instrukcja

12 Stycznia 2025
Makita

Makita DUC306PG2 Instrukcja

12 Stycznia 2025
HiKOKI

HiKOKI C 6BU3 Instrukcja

11 Stycznia 2025
DEDRA

DEDRA DED7060 Instrukcja

11 Stycznia 2025
Einhell

Einhell KGS 190 Instrukcja

11 Stycznia 2025
Sun Joe

Sun Joe SWJ599E Instrukcja

11 Stycznia 2025
Einhell

Einhell BT-MB 550 U Instrukcja

11 Stycznia 2025
Maruyama

Maruyama MCV51 Instrukcja

11 Stycznia 2025
Vonroc

Vonroc JS505DC Instrukcja

9 Stycznia 2025