Instrukcja obsługi Posiflex LS-1000U

Posiflex czytnik kodów kreskowych LS-1000U

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Posiflex LS-1000U (22 stron) w kategorii czytnik kodów kreskowych. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/22

FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual,

may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to EN55022 and 47

CFR, Part 2 and subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to

take whatever measures to correct the interference.

For CE-countries: This scanner is in conformity with CE standards. Please note that an approved, CE-marked power supply unit should be used in order to

maintain CE conformance.

Laser Safety: The laser scanner complies with safety standard IEC 60825 –1 for a Class I laser produce. It also complies with CDRH as applicable to a

Class IIa laser product. Avoid long term staring into direct laser light.

Radiant Energy: The laser scanner uses one low- -power visible laser diodes operating at 650nm in an opto mechanical scanner resulting in less than 3.9µW

radiated power as observed through a 7mm aperture and averaged over 10 seconds.

Do not attempt to remove the protective housing of the scanner, as unscanned laser light with a peak output up to 0.8mW would be accessible inside.

Laser Light Viewing: The scan window is the only aperture through which laser light may be observed from this product. A failure of the scanner motor,

while the laser diode continues to emit a laser beam, may cause emission levels to exceed those for safe operation. The scanner has safeguards to prevent

this occurrence. If, however, a stationary laser beam is emitted, the failing scanner should be disconnected from its power source immediately.

Adjustments: Do not attempt any adjustments or alteration of this product. Do not remove the protective housing of the scanner. There are no user-

serviceable parts inside.

Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.

Optical: The use of optical instruments with this product will increase the eye hazard. Optical instruments include binoculars, magnifying glasses, and

microscopes but do not include normal eye glasses worn by the user.

Warranty Limits: Warranty terminates automatically when any person other than the authorized technicians opens the machine. The user should consult

his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is

by no means responsible for any damage or hazard caused by improper application.

No part of this document may be reproduced, transmitted, stored in a retrieval system, transcribed, or translated into any language or

computer language in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without express

written consent and authorization.

We reserve the right to make changes in product design without reservation and without notification. The material in this guide is for

information only and is subject to change without notice.

All trademarks mentioned herein, registered or otherwise, are the properties of their various respective owners.

About This Manual:

Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this manual. However, Posiflex Technologies, Inc. will assume no

liability for any technical inaccuracies or editorial or other errors or omissions contained herein, nor for direct, indirect, incidental, consequential or

otherwise damages, including without limitation loss of data or profits, resulting from furnishing, performance, or use of this material.

This information is provided “ ”as is and Posiflex Technologies, Inc. expressly disclaims any warranties, expressed, implied or statutory, including without

limitation implied warranties of merchantability or fitness for particular purpose, good title and against infringement.

The information in this manual contains only essential hardware concerns for general user and is subject to change without notice. Posiflex Technologies,

Inc. reserves the right to alter product designs, layouts or drivers without notification. The system integrator shall provide applicative notices and

arrangement for special options utilizing this product. The user may find the most up to date information of the hardware from: http://www.posiflex.com or

http://www.posiflex.com.tw or http://www.posiflexusa.com

All data should be backed-up prior to the installation of any drive unit or storage peripheral. Posiflex Technologies, Inc. will not be responsible for any loss

of data resulting from the use, disuse or misuse of this or any other Posiflex product.

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,

electronic, mechanical, photocopying, or otherwise, without prior express written consent from Posiflex Technologies, Inc. the publisher of this

documentation.

All brand and product names and trademarks are the property of their respective holders.

1000 Series

Laser Barcode Scanner

User’s Manual

Rev. A0

P/N: 1805 0030090

Page 1

FUNDAMENTAL INFORMATION

MODEL NAME: LS-1000

CONTENT (Besides this guide):

Fig. 1 Box content besides this guide

INSTALLATION GUIDES

1. Install the USB or RS232 interface cable onto

the scanner by inserting the 8 pin RJ45 type

modular plug (Fig. 2) of the cable into the

scanner until a firm click is heard.

2. Use the stand fixing

screw to fit the stand on a

wooden desktop (Fig. 3).

3. Seat the scanner unit into the

stand and connect the

interface cable to an

appropriate USB or RS232

port (Fig. 4). Connect the

power adaptor to the power

input connector on interface cable (Fig. 5) or set the

+5V power support in pin 9 of the system COM port

for RS232 model. Set the COM port protocol to 9600, n,

8, 1 and no handshaking for RS232

model. Peel off the protective film on

scanner for ready to use after all the

operations done. The scanner will always

be in omni-directional scan mode when it

is in the stand.

Scanner Unit

Stand

Interface Cable

Stand Fixing Screw

Fig. 4 LS-1000 in Stand

Fig. 2 RJ45 Type Modular Plug

Fig. 3 Fix The Stand

Fig. 5 RS232 Power Connection

Page 2

Description Function

Scan Window Reads barcodes

Object Detector Trigger and wake up scanner automatically

when

presented with barcode in its range

Beeper Hole For beep tone indication

USING THE SCANNER

SCANNER INTRODUCTION

Features

The scanner unit is a compact and space- - -saving hands free omni directional laser

scanner. It can operate in a single-line laser scan mode by pressing down a button.

Featured with Z- -scan hardware decode technology, it guarantees the real time decode

and provide the best scanning performance you could expect.

The scanner includes key features as:

l Button switch in between omni-directional and single–line scanning

capability, ideal for increasing your operating efficiency.

l Powerful 20-line scan pattern yields:

ü 1400 scans per second for omni-directional scanning

ü 74 scans per second for single-line scanning

l Implement with the proprietary real-time hardware decoding technology

that ensures instant recognition and decoding barcodes

Parts Identification

Each part of the scanner as indicated in the front and rear pictures below is

described in the table below.

Function Button

Scan Window

Mounting Screw Hole

Object Detector

Beeper Hole

Interface Cable Connector

Page 3

Specyfikacje produktu

Marka:	Posiflex
Kategoria:	czytnik kodów kreskowych
Model:	LS-1000U

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Posiflex LS-1000U, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje czytnik kodów kreskowych Posiflex

Posiflex CD-3602U Instrukcja

9 Października 2024

Posiflex CD-3202U Instrukcja

9 Października 2024

Posiflex CD-3860UN Instrukcja

12 Września 2024

Posiflex LS-3000U Instrukcja

9 Września 2024

Posiflex CD-3870U Instrukcja

8 Września 2024

Posiflex CD-2860U-B Instrukcja

8 Września 2024

Posiflex CD-3601U Instrukcja

7 Września 2024

Posiflex CD-3201U Instrukcja

6 Września 2024

Posiflex LS-1000U Instrukcja

6 Września 2024

Posiflex LS-1000 Instrukcja

6 Września 2024

Instrukcje czytnik kodów kreskowych

Najnowsze instrukcje dla czytnik kodów kreskowych

Datalogic CBX500 Instrukcja

9 Października 2024

Brady IRX200 Instrukcja

8 Października 2024

Newland HR33 Marlin filaire Instrukcja

8 Października 2024

Wasp WDI9600 Instrukcja

7 Października 2024

Wasp WLS9500 Instrukcja

7 Października 2024

Wasp WCS3900 Instrukcja

7 Października 2024

Wasp WDI4600 Instrukcja

7 Października 2024

Wasp WLR8900 Instrukcja

7 Października 2024

Wasp WCS3905 Instrukcja

7 Października 2024

Wasp WLS8600 Instrukcja

7 Października 2024