Instrukcja obsługi Posiflex CD-3202U

Posiflex czytnik kodów kreskowych CD-3202U

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Posiflex CD-3202U (20 stron) w kategorii czytnik kodów kreskowych. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/20
1
Package Contents
CD- 2U 320
CD- 2U 2D image scanner 320
ST-8000 scanner holder stand
(Optional)
USB cable
CD- 2R 320
CD- 2R 2D image scanner 320
ST-8000 scanner holder stand
(Optional)
RS-232 cable
Product Overview
Front View
Rear View
CD-3202U/R Ver. A0
Trigger Button
Status LED
CD-3202U/R
2D Image Scanner
Quick Setup Guide
2
Scanner Maintenance
The scanner is designed for long-term trouble-free operation and rarely
requires any maintenance. Only an occasional cleaning of the scanner window
is necessary in order to remove dirt and ngerprints.
Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to
avoid the scan window from being scratch and damag . The scan window ed ed
can be cleaned while the scanner is running.
The standard interface cable is attached to the scanner with a 10-pin modular
connector. When the connector is properly seated, it is secured in the scanner
by a exible retention tab. The cable is designed to be eld replaceable.
Replacement cables can be obtained from your authorized distributor. To
replace the cable, take the following steps.
1. Make sure the power of both the host terminal and the scanner is powered
o.
2. Disconnect the old scanner cable from the host terminal.
3. Press down the retention tab, and gently pull out the cable.
4. Insert the new interface cable into the bottom of the scanner until it clicks.
Then, plug the new cable into the host.
LED Indication
Status
Explanation
Blue LED ashes one time
Good read
Troubleshooting
This section contains information about how to solve problems that you may
encounter when operating the scanner. If a trouble occurs please refer to the ,
following diagnostic tips as a mean to solve the trouble. However, before
referring to the tips, make sure that the scanner is installed well. If the problem
remains, contact your dealer.
Problem
Diagnostic Tips
The scanner is on but cannot read
any barcode.
The scanner window is dirty. Clean the scanner
window as described in the Scanner
Maintenance section.
The presented barcode type is not enabled. Use
this guide to tell the scanner to accept that type
of barcode.
The host terminal has disabled the scanner.
Check the setup of host terminal.
The barcode type presented is not supported by
the scanner.
3
Problem
Diagnostic Tips
The scanner does not accept more
than two or three barcode labels.
Determine whether the required barcode types
are enabled or not.
A stray barcode is sitting somewhere in the
scanner eld of view. Remove all barcode labels
from the scanner’s scan volume and try again.
The scanner cannot send the data to the POS
system. Make sure that the scanner is installed
well and your host POS system is ready to
receive data.
A barcode is read by the scanner
but not accepted by the POS
system.
The communication settings of the system port
and the scanner do not match. Adjust the settings
to make them match to each other.
The scanner is not installed well. Contact your
dealer for the proper installation. The software
running on the POS system does not support the
data format of the barcode label.
When a barcode stays close to the
scanner, the barcode cannot be read
automatically by the scanner.
Check whether or not you have enabled the
Manual Trigger mode. If you have enabled this
mode accidentally, please disable the Manual
Trigger mode by scanning the “Disable trigger”
barcode in the advanced user manual.
Programming Codes
Below are some suggestion you need to bear mind while scanning labels: in
1. The barcode labels shown in bold and black are default factory
settings.
2. Please cover the unwanted codes for scanning the specic barcode
required for the programming to prevent confusion in code scanning.
3. Use the user manual downloaded from our global website for advanced
programming.
4. While scanning the setup barcode labels provided in the quick guide, you
need to pull the trigger to initiate the decoding process.
Firmware Version
Scan the below barcode label to retrieve the current rmware version.
Query Firmware Version

Specyfikacje produktu

Marka: Posiflex
Kategoria: czytnik kodów kreskowych
Model: CD-3202U

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Posiflex CD-3202U, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje czytnik kodów kreskowych Posiflex

Posiflex

Posiflex CD-3602U Instrukcja

9 Października 2024
Posiflex

Posiflex CD-3202U Instrukcja

9 Października 2024
Posiflex

Posiflex CD-3860UN Instrukcja

12 Września 2024
Posiflex

Posiflex LS-3000U Instrukcja

9 Września 2024
Posiflex

Posiflex CD-3870U Instrukcja

8 Września 2024
Posiflex

Posiflex CD-3601U Instrukcja

7 Września 2024
Posiflex

Posiflex CD-3201U Instrukcja

6 Września 2024
Posiflex

Posiflex LS-1000U Instrukcja

6 Września 2024

Instrukcje czytnik kodów kreskowych

Najnowsze instrukcje dla czytnik kodów kreskowych

Datalogic

Datalogic CBX500 Instrukcja

9 Października 2024
Brady

Brady IRX200 Instrukcja

8 Października 2024
Newland

Newland HR33 Marlin filaire Instrukcja

8 Października 2024
Wasp

Wasp WDI9600 Instrukcja

7 Października 2024
Wasp

Wasp WLS9500 Instrukcja

7 Października 2024
Wasp

Wasp WCS3900 Instrukcja

7 Października 2024
Wasp

Wasp WDI4600 Instrukcja

7 Października 2024
Wasp

Wasp WLR8900 Instrukcja

7 Października 2024
Wasp

Wasp WCS3905 Instrukcja

7 Października 2024
Wasp

Wasp WLS8600 Instrukcja

7 Października 2024