Instrukcja obsługi Posiflex CD-3602U
Posiflex
Barcode lezer
CD-3602U
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Posiflex CD-3602U (21 stron) w kategorii Barcode lezer . Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/21
1
Package Contents
CD- 2U 360
2D image scanner
USB cable
Quick setup guide
CD- 2R 360
2D image scanner
RS-232 cable
Quick setup guide
Parts of the 2D Image Scanner
Trigger Button1
Scan Window
w/ Object Detector
Mounting Screw Hole
Beeper Hole
Interface Cable Connector
CD- 2 (U/R) 360
2D Image Scanner
Quick Setup Guide
CD-3602U/R Ver. A0
2
Scanner Maintenance
The scanner is designed for long-term trouble-free operation and rarely
requires any maintenance. Only an occasional cleaning of the scanner window
is necessary in order to remove dirt and ngerprints.
Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to
avoid the scan window from being scratch and damag . The scan window ed ed
can be cleaned while the scanner is running.
The standard interface cable is attached to the scanner with a 10-pin modular
connector. When the connector is properly seated, it is secured in the scanner
by a exible retention tab. The cable is designed to be eld replaceable.
Replacement cables can be obtained from your authorized distributor. To
replace the cable, take the following steps.
1. Make sure the power of both the host terminal and the scanner is powered
o.
2. Disconnect the old scanner cable from the host terminal.
3. Press down the retention tab, and gently pull out the cable.
4. Insert the new interface cable into the bottom of the scanner until it clicks.
Then, plug the new cable into the host.
Troubleshooting
This section contains information about how to solve problems that you may
encounter when operating the scanner. If a trouble occurs please refer to the ,
following diagnostic tips as a mean to solve the trouble. However, before
referring to the tips, make sure that the scanner is installed well. If the problem
remains, contact your dealer.
Problem
Diagnostic Tips
The scanner is on but cannot read
any barcode.
The scanner window is dirty. Clean the scanner
window as described in the Scanner
Maintenance section.
The presented barcode type is not enabled. Use
this guide to tell the scanner to accept that type
of barcode.
The host terminal has disabled the scanner.
Check the setup of host terminal.
The barcode type presented is not supported by
the scanner.
The scanner does not accept more
than two or three barcode labels.
Determine whether the required barcode types
are enabled or not.
3
Problem
Diagnostic Tips
A stray barcode is sitting somewhere in the
scanner eld of view. Remove all barcode labels
from the scanner’s scan volume and try again.
The scanner cannot send the data to the POS
system. Make sure that the scanner is installed
well and your host POS system is ready to
receive data.
A barcode is read by the scanner
but not accepted by the POS
system.
The communication settings of the system port
and the scanner do not match. Adjust the settings
to make them match to each other.
The scanner is not installed well. Contact your
dealer for the proper installation. The software
running on the POS system does not support the
data format of the barcode label.
When a barcode stays close to the
scanner, the barcode cannot be read
automatically by the scanner.
Check whether or not you have enabled the
Manual Trigger mode. If you have enabled this
mode accidentally, please disable the Manual
Trigger mode by scanning the “Disable trigger”
barcode in the advanced user manual.
Programming Codes
Below are some suggestion you need to bear in mind while scanning labels:
1. The barcode labels shown in bold and black are default factory
settings.
2. Please cover the unwanted codes for scanning the specic barcode
required for the programming to prevent confusion in code scanning.
3. Use the user manual downloaded from our global website for advanced
programming.
4. While scanning the setup barcode labels provided in the quick guide, you
need to pull the trigger to initiate the decoding process.
Firmware Version
Scan the below barcode label to retrieve the current rmware version.
Query Firmware Version
Specyfikacje produktu
Marka: | Posiflex |
Kategoria: | Barcode lezer |
Model: | CD-3602U |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Posiflex CD-3602U, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Barcode lezer Posiflex
9 Października 2024
9 Października 2024
7 Września 2024
6 Września 2024
6 Września 2024
Instrukcje Barcode lezer
- Barcode lezer Bluebird
- Barcode lezer Garmin
- Barcode lezer Honeywell
- Barcode lezer Manhattan
- Barcode lezer Zebra
- Barcode lezer IFM
- Barcode lezer Digitus
- Barcode lezer Datalogic
- Barcode lezer Intermec
- Barcode lezer Datamax O'Neil
- Barcode lezer Newland
- Barcode lezer Socket Mobile
- Barcode lezer Qian
- Barcode lezer Brady
- Barcode lezer Nilox
- Barcode lezer Steren
- Barcode lezer Palm
- Barcode lezer IC Intracom
- Barcode lezer Adesso
- Barcode lezer POSline
- Barcode lezer Baracoda
- Barcode lezer CipherLab
- Barcode lezer Trimble
- Barcode lezer DENSO
- Barcode lezer EC Line
- Barcode lezer Code Corporation
- Barcode lezer Wasp
- Barcode lezer Vultech
- Barcode lezer Psion
- Barcode lezer Unitech
- Barcode lezer Opticon
- Barcode lezer Atlantis Land
- Barcode lezer ID-Tech
- Barcode lezer Code
Najnowsze instrukcje dla Barcode lezer
9 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024