Instrukcja obsługi Joranalogue Receive 2

Joranalogue nieskategoryzowany Receive 2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Joranalogue Receive 2 (5 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/5
RECEIVE 2
DUAL LINE BALANCED IN
PUTS
1
INTRODUC TIO N
While modular synthesisers are most often used
as stand-alone instruments, they also present
exciting opportunities for processing external
signals. Anything from an electric guitar to an
effects send on a studio mixing desk can benefit
from the unique sonic capabilities of even a
modest Eurorack system.
However, patching in an external source usually
requires an adapter cable and plenty of clean
gain to bring the signal to Eurorack level. If the
signal source is balanced, a balanced input is
required as well to provide the best possible
interference rejection.
Receive 2 (or RX2 for short) provides a convenient
all- -in one solution. It offers two universal external
inputs, which accept both balanced or single-
ended signals via XLR or 6.35 mm jack
connectors.
The circuit incorporates impedance design low-
practices, RF filtering and premium balanced
receivers to provide transformer-like
interconnect performance in a compact and
affordable module. And thanks to the
electrostatic protection it’s discharge (ESD) ,
rugged enough to survive the rigours of
performing on the road.
The turevery clean integrated pre-amps fea
variable gain, ranging from unity to +40 dB on
each channel. As a result, Receive 2 can handle
just about any signal source you may encounter,
including electric instruments, piezoelectric
pickups and many dynamic microphones.
Adjusting the gains is a breeze thanks to the dual
peak- . responding LED meters A mix output is
included as well, so external signals can be easily
mixed directly in the module.
CONTENTS
In the Receive 2 box, you’ll find:
Product card, stating serial number and
production batch.
16- - -to 10 pin Eurorack power cable.
Mounting hardware: two black M3 x 6 mm
hex screws, two black nylon washers and a
hex key.
And finally, the module itself, in a protective
cotton bag.
If any of these items are missing, please contact
your dealer or support@joranalogue.com.
RECEIVE 2
DUAL LINE BALANCED IN
PUTS
2
CONTROL S & CONNECTI ONS
1 LED METERS
The peak-responding LED bar meters give a
visual indication of the output levels on the
3.5 mm sockets. The scale ranges from −18 to
+6 10 dB, with 0 dB corresponding to the Vpp
nominal Eurorack level. Be aware that since
Eurorack has limited headroom, +6 dB is very
close to clipping.
2 GAIN KNOBS
Use these knobs to adjust the input gain for each
channel dB. With dBu, from 0 (unity) to +40 +4
balanced ‘professional’ input signals, they will
typically be set at about 25 % 10 (+ dB) to reach
10 Vpp on the main output sockets. For − V 10 dB
‘ - consumer’ single ended input signals, you can
expect about dB) to be the ideal 75 30 % (+
amount of gain. Passive sources such as dynamic
microphones of may require the maximum gain
+40 dB.
3 MAIN OUTPUTS
These are the main Eurorack outputs. Connect
them to the modules you’d like to process the
external signal(s) through.
4 MIX OUTPUT
Both input signals are also mixed together
internally, and the result is available from this
output socket. The signals are attenuated by
6 dB before mixing to avoid clipping.
5 EXTERNAL INPUTS
Connect your external signals here. Just about
any signal source may be connected: balanced
or single- ended, via XLR or 6.35 mm jack
connectors.
Note that the inputs are DC-coupled, so any DC
offset that may be present is retained. This makes
it possible to e receiv external CV signals,
although DC accuracy may not be sufficient to
process pitch CV.
RECEIVE 2
DUAL LINE BALANCED IN
PUTS
3
6 GROUND SHORT SOLDER BRIDGE
Receive 2 features separate signal and chassis
ground planes, joined together at the front panel.
This helps to avoid ground currents running
through the circuitry and causing audible
interference, provided the module is installed in
a Eurorack enclosure which is properly earth-
connected at its chassis.
In sub-optimal installations, shorting together
the ground planes on the rear of the circuit board
at the ‘ground short’ solder bridge point may
improve performance.

Specyfikacje produktu

Marka: Joranalogue
Kategoria: nieskategoryzowany
Model: Receive 2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Joranalogue Receive 2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Joranalogue

Joranalogue

Joranalogue Cycle 5 Instrukcja

14 Lipca 2024
Joranalogue

Joranalogue Dim 2 Instrukcja

13 Lipca 2024
Joranalogue

Joranalogue Route 4 Instrukcja

13 Lipca 2024
Joranalogue

Joranalogue Contour 1 Instrukcja

13 Lipca 2024
Joranalogue

Joranalogue Compare 2 Instrukcja

13 Lipca 2024
Joranalogue

Joranalogue Fold 6 Instrukcja

13 Lipca 2024
Joranalogue

Joranalogue Generate 3 Instrukcja

13 Lipca 2024
Joranalogue

Joranalogue Select 2 Instrukcja

13 Lipca 2024
Joranalogue

Joranalogue Mix 3 Instrukcja

13 Lipca 2024
Joranalogue

Joranalogue Orbit 3 Instrukcja

13 Lipca 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024