Instrukcja obsługi I-PRO WV-QEM500-W

I-PRO Nie skategoryzowane WV-QEM500-W

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla I-PRO WV-QEM500-W (2 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Ns0520-1042

Printed in China

Ceiling Mount Bracket

Model No. WV-QEM500-W

Operating Instructions

• Before attempting to connect or install this product, please read these instructions carefully and

save this manual for future use.

• The external appearance and other parts shown in this manual may differ from the actual product

within the scope that will not interfere with normal use due to improvement of the product.

Preface

This product is a ceiling embedded bracket that is designed to mount the network camera on a

ceiling. This bracket can be used for an area with weak pull-out strength such as plasterboard in a

double ceiling, and the embedded type makes the visible part of the camera smaller.

For the latest information about the supported cameras, refer to our support website (https://i-pro.

com/global/en/surveillance/training_support/support/technical_information <Control No.:C0501>).

Refer installation work to the dealer.

Installation work requires technique and experience. Failure to observe this may cause fire, electric

shock, injury, or damage to the product.

Be sure to consult the dealer.

Do not use this bracket except with suitable cameras.

Failure to observe this may cause a drop resulting in injury or accidents.

The measures of protection against a fall of this product shall be taken.

Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety

wire.

Install the product securely on a ceiling in accordance with the installation instructions.

Failure to observe this may cause injury or accidents.

Do not rub the edges of metal parts with your hand.

Failure to observe this may cause injury.

When using this product, also read the “Precautions” described in the operating

instructions for the camera to be attached.

Precautions

Installation

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting

from failures arising out of improper installation or operation inconsistent with this

documentation.

Caution:

• Before attempting to connect or operate this

product, please read these instructions care-

fully.

Notice:

• This product is not suitable for use in loca-

tions where children are likely to be present.

• Do not install this product in locations where

ordinary persons can easily reach.

• For information about screws and brackets

required for installation, refer to the corre-

sponding section of this document.

Included Installation Instructions Specifications

Ambient operating temperature: –50 °C to +60 °C {–58 °F to +140 °F}

Dimensions: ø211.3 mm × 117 mm (H)* {ø8-5/16 inches × 4-19/32 inches}

*Including decorative cover thickness: 13 mm {1/2 inches}

Mass: Approx. 870 {1.92 lbs}g

Finish: Main body: Surface treatment steel sheet

Decorative cover: ABS resin

i-PRO white

■ In order to prevent injury, the product must be securely mounted to the ceiling

according to the Installation Guide of the camera.

■ This product is designed to be used indoors.

This product is not operable outdoors. Do not expose this product to direct sunlight for hours and

do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation,

discoloration and malfunction. Keep this product away from water and moisture.

■Installation area for this product

Make sure that the installation area is strong enough to hold

the total weight of the camera assembly before installation.

The installation area shall have 210mm {8-9/32inches} or

more space behind the ceiling.

The thickness of the ceiling board for installation can range

between 9mm {3/8inches} and 40mm {1-9/16inches}.

■ Make sure to remove this product if it will no longer be used.

Precautions for installation

210mm

{8-9/32inches}

or more

Ceiling board: between

9mm {3/8inches} and

40mm {1-9/16inches}

Standard Accessories

Operating Instructions (this document) 1 pc. .......

Safety wire 1 pc. .................................................

Safety wire angle 1 pc. .......................................

Template A 1 pc. ................................................

Template B 1 pc. ................................................

Decorative cover 1 pc. ........................................

Refer to the operating instructions of the camera for details on the camera installation

(including the camera mounting, cable connection and adjustment).

Step 1 Put Template A (accessory) against the ceiling and make a hole.

①Make 4 holes of 12 mm {1/2 inches} in

diameter.

②Remove the center part from the template.

③ Make a hole of 180 mm {7-1/16 inches} in

diameter.

The ceiling hole shape

is shown in the drawing

at right.

Step 2 Install two anchor bolts (M10: locally procured) into the ceiling.

① Determine the anchor bolt length (for securing the mounting chassis) by use of Template B

(accessory).

② Position the nut by use of Template B (accessory) and mount the nut. (The distance between the

bottom surfaces of the ceiling board and nut shall be 134 mm {5-1/4 inches}.)

ø12 mm {1/2 inches}

(4 positions)

Ceiling faceø180 mm

{7-1/16 inches}

Template A

IMPORTANT:

⿟When the existing anchor bolt is used as an anchor bolt for connecting the safety wire,

make sure that the distance between the anchor bolt and camera mounting position is 1 m

{3.28 feet} or less.

Anchor bolt (M10)* 2 pcs. Nut (M10) 6 pcs. .................................... ................................................

Other items that are needed (not included)

* One anchor is used for securing the mounting chassis, and the other anchor is used for

connecting the safety wire. (See Step2)

IMPORTANT

⿟Prepare anchor bolts according to the material and strength of the area where the product is

to be installed. The pull-out strength of the anchor bolt shall be more than 5 times of the total

weight of the installed devices (including the camera body, ceiling mount bracket, anchor

bolts, and all other parts).

Anchor bolt

(for connecting the safety wire)

①Mount a nut

②Determine the anchor bolt length

Install the anchor bolt in the center of the hole

134 mm {5-1/4 inches}

Template B

Ceiling board

Anchor bolt

(for securing the mounting chassis)

1 m {3.28 feet} or less

For U.S. and Canada:

i-PRO Americas Inc.

For Europe and other countries:

i-PRO EMEA B.V.

https://www.i-pro.com/

Step 3

Secure the safety wire angle (accessory) to the anchor bolt (for

connecting the safety wire), and connect the safety wire (accessory).

① Mount a nut so that the safety wire angle

is secured on the anchor bolt.

② Remove the safety wire from the safety

wire angle.

③ Insert the groove of the portion of the ❶

safety wire angle into the anchor bolt.

④ Close the safety wire angle while inserting

the groove of the portion of the safety ❷

wire angle into the anchor bolt.

⑤ Connect the safety wire to the safety wire

angle again.

⑥ Engage the nut from beneath, and secure

the safety wire angle with top and bottom

nuts.

⑦ Engage another nut from beneath to

tighten and secure the nut that was

engaged from beneath in in a double ⑥

nut fashion.

Note:

⿟When the existing anchor bolt that

has been installed is used for

connecting the safety wire, the use

of 2 spacer nuts is helpful.

Step 4 Attach the safety wire.

① Mount a nut so that the mounting chassis is

secured on the anchor bolt(for securing the

mounting chassis).

② Attach the safety wire to the mounting chas-

sis as shown in the right illustration.

Spacer nuts Spacer nuts

Safety wire angle

Existing anchor bolt

Safety wire

Upper side

Lower

side

Safety wire

③Insert

②Remove

④Close

❷

❶

⑤Connect

Safety wire angle

Anchor bolt

Safety wire

(Accessory)

Roof space

Ceiling board

Cables

Mounting

chassis

Step 5 Insert the anchor bolt into the mounting hole of the mounting

chassis.

To adjust the position of the i-PRO logo on

the decorative cover, rotate the mounting

chassis. Note that the i-PRO logo will be

located at approximately 180° opposite side

of a hook for the decorative cover.

Step 6 Secure the mounting chassis.

① Secure the mounting chassis to the ceiling

board with the ceiling board fixing screws

(4places).

Turning the ceiling board fixing screws clock-

wise provides ceiling board tightening

between the bottom of the mounting chassis

and ceiling board fixing bracket resulting in

mounting chassis securing.

Recommended tightening torque:

0.78 N·m {0.58 lbf·ft}

② Use double nuts (locally procured) to secure the mounting chassis after inserting the anchor bolt

(for securing the mounting chassis).

Step 7 Mount the attachment plate.

① Mount the attachment plate (accessory of the

camera) to this mounting chassis. Use fixing

screws for attachment plate (M4:accessory of

the camera) to secure the attachment plate

firmly as shown in the right illustration.

Recommended tightening torque:

0.78N·m {0.58lbf·ft}

Mounting

hole

Hooks (3 places)

Approx. 10°

Direction of brand logo

Anchor bolt

(for securing the mounting chassis)

Ceiling board

fixing bracket

(4 places)

Ceiling board

fixing screw

(4 places)

Turn

clockwise

Double nuts

(locally procured)

Ceiling board

Anchor bolt

(for connecting the safety wire)

IMPORTANT:

⿟When securing this bracket on the ceil-

ing, make sure that the four ceiling

board fixing brackets are open as

shown in the right illustration.

Step 8

Connect the cables and mount the camera on the attachment plate.

Step 9 Fix the camera.

Remove the enclosure from the camera and fix the camera firmly by tightening the camera fixing

screw (red).

Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

Mounting chassis

Attachment plate

(accessory of the

camera)

Fixing screws for attachment plate (4 pcs.)

(M4:accessory of the camera)

Step 10 Adjust the camera.

After adjusting the angle of view, attach the enclosure to the camera as it was before.

Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

Step 11 Mount the decorative cover.

Mount the decorative cover on this mount

bracket.

• Align the “I” mark of the decorative cover

supplied with this mounting chassis with the

hook of the mounting chassis, press the

decorative cover against the ceiling, and rotate

the decorative cover clockwise when viewing it

from beneath to secure the cover.

Decorative cover

“I” Mark

Projections (3 places)

Projection

Hooks for the

decorative cover

(3 places)

Existing anchor bolt

Safety wire

Safety wire angle

Nut

(locally procured)

Fix the hook of the

safety wire to this

product. Camera fixing screw (red).

Hook of the mounting chassis

Enclosure

Specyfikacje produktu

Marka:	I-PRO
Kategoria:	Nie skategoryzowane
Model:	WV-QEM500-W

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z I-PRO WV-QEM500-W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Nie skategoryzowane I-PRO

I-PRO WV-QEM500-W Instrukcja

27 Marca 2025

I-PRO WV-QEM100-W Instrukcja

27 Marca 2025

I-PRO WV-QJB501-W Instrukcja

27 Marca 2025

I-PRO WV-QJB502-W Instrukcja

13 Marca 2025

I-PRO WV-QED100G Instrukcja

10 Lutego 2025

I-PRO WV-QJB506 Instrukcja

10 Lutego 2025

I-PRO WV-QDC509CN Instrukcja

30 Stycznia 2025

I-PRO WV-QSR503 Instrukcja

30 Stycznia 2025

I-PRO WV-QDC501G Instrukcja

30 Stycznia 2025

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane

Evga XC3 Instrukcja

30 Marca 2025

InLine 61602C Instrukcja

30 Marca 2025

American DJ Ultra HEX Bar 12 Instrukcja

30 Marca 2025

Kica Jet Fan 2 Instrukcja

30 Marca 2025

Osprey FL-OSP-220L Instrukcja

30 Marca 2025

Sophos SD-RED 60 Instrukcja

30 Marca 2025

Fender Hammertone Reverb Instrukcja

30 Marca 2025

Fender Bassman Fuzz Instrukcja

30 Marca 2025

Fender Bassman Delay Instrukcja

30 Marca 2025

Fender Bassman Driver Instrukcja

30 Marca 2025