Instrukcja obsługi I-PRO WV-QJB502-W

I-PRO Nie skategoryzowane WV-QJB502-W

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla I-PRO WV-QJB502-W (2 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Preface

Mount the camera onto the ceiling or wall using this bracket.

Use this bracket when conduits are used for wiring, or when there is no space

available for wiring in the ceiling or wall.

For the latest information about the supported cameras, refer to our support website

(

https://i-pro.com/global/en/surveillance/training_support/support/technical_information

Specifications

Ambient operating temperature: –50 °C to +60 °C {–58 °F to +140 °F}

Dimensions: ø127 mm × 56.5 mm (H) {ø5 inches × 2-7/32 inches(H)}

Mass: Approx. 470 {1.04 lbs}g

Finish: Aluminum die cast

i-PRO white <WV-QJB502-W>

Light gray <WV-QJB502-G>

Precautions for installation

■ In order to prevent injury, the product must be securely mounted to the wall or ceiling

according to the Installation Guide of the camera.

■ Make sure to remove this product if it will no longer be used.

Standard accessories

Operating Instructions (this manual) .......... 1 pc.

The following parts are used during installation procedures.

Other items that are needed (not included)

• Fixing screw Recommended screw M4/4 or 2 pcs.

Minimum pull-out strength 196 N {44 lbf} (per 1 pc.)

Note:

• Select screws according to the material of the location that the camera will be mounted to.

In this case, wood screws and nails should not be used.

• For information about the minimum pull-out strength, refer to our support website

(https://i-pro.com/global/en/surveillance/training_support/support/technical_information

<Control No.: C0120>)

Attachment plate ......................................1 pc.

Fixing screw for camera

(M4×10 mm {13/32inches}) .................... 4 pcs.

(of them, 1 for spare)

Fixing screw for attachment plate

(M3×10 mm {13/32 inches}) ................... 5 pcs.

(of them, 1 for spare)

Cover ....................................................... 1 pc.

Ns1020-2042

Precautions

■ Do not use this bracket except with suitable cameras.

Failure to observe this may cause a drop resulting in injury or accidents.

■ Do not install this product on a place that is greatly inﬂ uenced by wind.

Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or more may cause

a fall of the product resulting in injury or accidents.

■ Refer installation work to the dealer.

Installation work requires technique and experience. Failure to observe this may cause fire,

electric shock, injury, or damage to the product. Be sure to consult the dealer.

■ Do not rub the edges of metal parts with your hand.

Failure to observe this may cause injury.

When using this product, also read the “Precautions” described in the operating instruc-

tions for the camera to be attached.

Operating Instructions

Included Installation Instructions

Base Bracket

Model No.

WV-QJB502-W

WV-QJB502-G

• Before attempting to connect or install this product, please read these instructions carefully and

save this manual for future use.

• T

he external appearance and other parts shown in this manual may differ from the actual

product within the scope that will not interfere with normal use due to improvement of the

product.

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting

from failures arising out of improper installation or operation inconsistent with this

documentation.

Preparations

[1] Remove the enclosure from the camera.

Refer to the Installation Guide of the corresponding camera for how to remove the enclosure

from the camera.

[2] Check the installation direction of the conduit and the image

capturing direction of the camera

Check the connection direction of the conduit (direction of the cable access hole for conduit

on this bracket) and the image capturing direction of the camera and then determine the

fixing position of the attachment plate. The fixing position of the attachment plate can be

changed with steps of 90°. The following is an example of the camera direction and the

fixing position of the attachment plate when connecting the conduit from the upper side.

Caution:

• Before attempting to connect or operate

this product, please read these instructions

carefully.

Notice:

• This product is not suitable for use in loca-

tions where children are likely to be present.

• Do not install this product in locations

where ordinary persons can easily reach.

• For information about screws and other

parts required for installation, refer to the

corresponding section of this document.

Camera

Base bracket

⇧TOP mark

Attachment plate

• Align the direction of the attach-

ment plate so that the “ TOP” ⇧

mark of the attachment plate

comes to the upper side.

• Align the direction of the attach-

ment plate so that the “ TOP” ⇧

mark of the attachment plate

comes to the right side.

Note:

• The connection cable is

omitted in the illustration.

Camera

⇧TOP mark

Attachment plate

Base bracket

For U.S. and Canada:

i-PRO Americas Inc.

For Europe and other countries:

i-PRO EMEA B.V.

https://www.i-pro.com/

Parts and functions

Installations

Step1 Make a hole on the installation surface.

Make screw holes or anchor holes in the ceiling or wall, and also cable access hole if [1]

necessary.

No cable access hole is needed when using conduit.

Attachment plate

(accessory)

Fixing screw for

attachment plate

(4pcs.)

(M3×10 mm {13/32

inches}: accessory)

Conduit wiring connector

Cable access hole

Base bracket

Note:

• When mounting to a single-gang junction

box, fix it with screws (2 pcs.) (M4: locally

procured).

• The direction of the attachment plate

(installation direction of the camera) can

be changed with steps of 90° even after

the base bracket is fixed.

83.5 mm × 46 mm

{3-9/32 inches × 1-13/16 inches}/

82.5 mm × 47.6 mm

{3-1/4 inches × 1-7/8 inches}

󱨶

󱨷

83.5 mm {3-9/32 inches}/

83.3 mm {3-9/32 inches}

󱨸

󱨹

63 mm {2-15/32 inches}/

63 mm {2-15/32 inches}

󱨺

Cable access hole

ø25.4 mm {ø1 inch}

Remove the cap for the female thread for the [2]

conduit using a 5 mm {3/16 inches} hexagon

wrench and attach the conduit.

The female thread for conduit is compliant

with ANSI NPSM (parallel pipe threads) 3/4 or

ISO 228-1 (parallel pipe threads) G3/4.

Step2 Fix the base bracket and install the attachment plate and cover in

the direction described in [2] of “Preparations”.

[1] Install the base bracket on the installation surface.

Fixing screws (4 pcs.) (M4: locally procured)

Minimum pull-out strength: 196 N {44 lbf} (per 1 pc.)

[2] Install the attachment plate onto the base bracket and then attach the cover to the

attachment plate. The following is an example when this bracket is installed on the wall.

(Recommended tightening torque: 0.69 N·m {0.51 lbf·ft})

Base bracket

Cap for the female thread for

the conduit

Note:

• When installing this bracket outdoors, be sure to apply waterproofing to the cable access

hole and fixing screw holes.

Cable

Fixing screw (4 pcs.)

(M4: locally procured)

Fixing screw for

attachment plate

(4 pcs.)

(M3×10 mm {13/32

inches}: accessory)

Attachment plate

Base bracket

Step3 Connect the cables to the camera.

Connect an Ethernet cable to the RJ45 network cable from the camera.

Refer to the Installation Guide of the camera for how to install the waterproof connector.

Step4 Fix the camera body to this bracket.

(Recommended tightening torque: 1.37 N·m {1.01 lbf·ft})

Cable

Fixing screw for camera (3 pcs.)

(M4×10 mm {13/32 inches}: accessory)

Cable

Base bracket

Fixing screw for camera (2 pcs.)

(M4×10 mm {13/32 inches}: accessory)

Note:

• When fixing the camera on this bracket, be careful not to pinch the cable with this bracket

and damage the cable sheath.

Step5 Adjust the angle of view of the camera.

Turn on the power of the camera and adjust the angular field of view of the camera.

Refer to the Installation Guide of the corresponding camera for how to connect to a network and

for how to adjust the angle of view of the camera.

Step6 Attach the enclosure.

After finishing the adjustment, attach the enclosure by following the instructions in the Installation

Guide of the corresponding camera.

Refer to the Installation Guide of the corresponding camera for the recommended tightening

torque to be applied when fixing the enclosure of the camera.

Cover

(accessory)

Cover

(accessory)

△

Flat portion

Mark

Specyfikacje produktu

Marka:	I-PRO
Kategoria:	Nie skategoryzowane
Model:	WV-QJB502-W

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z I-PRO WV-QJB502-W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Nie skategoryzowane I-PRO

I-PRO WV-QEM500-W Instrukcja

27 Marca 2025

I-PRO WV-QEM100-W Instrukcja

27 Marca 2025

I-PRO WV-QJB501-W Instrukcja

27 Marca 2025

I-PRO WV-QJB502-W Instrukcja

13 Marca 2025

I-PRO WV-QED100G Instrukcja

10 Lutego 2025

I-PRO WV-QJB506 Instrukcja

10 Lutego 2025

I-PRO WV-QDC509CN Instrukcja

30 Stycznia 2025

I-PRO WV-QSR503 Instrukcja

30 Stycznia 2025

I-PRO WV-QDC501G Instrukcja

30 Stycznia 2025

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane

Planet PWR-240-48 Instrukcja

9 Kwietnia 2025

CaterChef 445001 Instrukcja

9 Kwietnia 2025

Daikin EKWCTRDI1V3 Instrukcja

9 Kwietnia 2025

Simplified MFG SP18CAT120 Instrukcja

9 Kwietnia 2025

AudioQuest Pegasus Instrukcja

9 Kwietnia 2025

Reolink P330 Instrukcja

9 Kwietnia 2025

Reolink NVS16-8MB8 Instrukcja

9 Kwietnia 2025

Drive Medical RTL12045 Instrukcja

9 Kwietnia 2025

Kern MBC-A05 Instrukcja

9 Kwietnia 2025

Daikin EKEXVA250 Instrukcja

9 Kwietnia 2025