Instrukcja obsługi Da-Lite Tensioned Dual Masking Electrol

Da-Lite Ekran projekcyjny Tensioned Dual Masking Electrol

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Da-Lite Tensioned Dual Masking Electrol (8 stron) w kategorii Ekran projekcyjny. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: info@da-lite.com
Instruction Book for
TENSIONED DUAL MASKING ELECTROL®
The Da-Lite Difference.
1
IMPORTANT SAFETY INSTRUCTIONS
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rat-
ing at least equal to that of the appliance should be used.
Cords rated for less amperage than the appliance may over-
heat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric
shock when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by
the manufacturer may cause a risk of fire, electric shock, or
injury to persons.
SAVE THESE INSTRUCTIONS
2
PRE-INSTALLATION
1. Carefully unpack screen and remove outer wrapping from case.
2. Make sure to recheck measurements of screen location before installation.
3. Remove center support brackets (on 8' and wider screens only), reverse brackets and reinstall flush with the top of the
box.
INSTALLATION
1. Install screen by raising unit into position between joists at one end only. Install one lag screw in each mounting
bracket.
2. Level unit lengthwise with a carpenter’s level and plumb level. Secure opposite end.
CAUTION! Do not seal in until screen has been secured in position and properly tested for satisfactory operation.
3. Carefully remove three shipping brackets by removing six hex head screws from case and three phillips head
screws from aluminum slat. Use a phillips screwdriver, a hex socket and a ratchet. Slat should move freely (Fig. 1).
4. Detach access panel by removing screws (Fig. 1).
5. Remove junction box cover plate.
6. Install electric hook up that applies to your unit. Make sure to review your electrical installation checklist and wiring
diagram (included) for either 120 volt switch, 220/240 volt switch or low voltage control.
NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.
CAUTION! DO NOT CUT TAPE ON FABRIC WITH A KNIFE OR ANY SHARP TOOL. REMOVE BY HAND.
7. Carefully remove two wood boards securing mask surface to case.
8. Test installation by carefully running picture and mask surfaces up and down several times. Be prepared to stop
screen. Standard Duty Cycle: 1 MIN. ON / 3 MIN. OFF.
NOTE: When rolled down, the picture surface should wrap fully around the roller. No part of the roller should be exposed.
Picture and mask surfaces will automatically stop in the down position.
The mask will start down off the front of the roller, travel completely down past the bottom of the viewing surface,
then “step back” against the viewing surface to eliminate shadowing by rolling up the back side of the roller. Do not
adjust the limits to change this feature.
9. Run the picture and mask surfaces upward. When the picture and mask surfaces are fully up the limit switches (in
the motors) are tripped and the motors shut off.
10. Check for satisfactory condition by operating screen a few times. Reinstall access panel.
s
!
s
!
FIGURE 1 FIGURE 2
DRYWALL
SCREW
ACCESS PANEL
MACHINE SCREW
PHILLIPS HEAD SCREW
SHIPPING BRACKET
PICTURE SURFACE
MASK SURFACE
MASK MOTOR
SCREEN MOTOR
HEX HEAD SCREW

Specyfikacje produktu

Marka: Da-Lite
Kategoria: Ekran projekcyjny
Model: Tensioned Dual Masking Electrol

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Da-Lite Tensioned Dual Masking Electrol, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ekran projekcyjny Da-Lite

Da-Lite

Da-Lite Model C With CSR Instrukcja

7 Października 2024
Da-Lite

Da-Lite Designer Manual 76456MO Instrukcja

6 Października 2024
Da-Lite

Da-Lite Cinema Vision Instrukcja

1 Października 2024
Da-Lite

Da-Lite Model C 83401 Instrukcja

29 Września 2024
Da-Lite

Da-Lite Model B Instrukcja

27 Września 2024
Da-Lite

Da-Lite Perm-Wall 78676 Instrukcja

26 Września 2024
Da-Lite

Da-Lite DescenderPro 29788LS Instrukcja

17 Września 2024
Da-Lite

Da-Lite Flex Plex 29529 Instrukcja

12 Września 2024
Da-Lite

Da-Lite Da-Tex (Rear) Instrukcja

11 Września 2024
Da-Lite

Da-Lite Dual Format Imager 38063EV Instrukcja

11 Września 2024

Instrukcje Ekran projekcyjny

Najnowsze instrukcje dla Ekran projekcyjny

AWOL Vision

AWOL Vision ALR-220C Instrukcja

28 Stycznia 2025
Optoma

Optoma DS-3120PMG Instrukcja

11 Października 2024
EPV

EPV PGF106WH1-A4K Instrukcja

8 Października 2024
EPV

EPV PGF84WH1 Instrukcja

8 Października 2024
Celexon

Celexon Ultramobile Plus Professional 194 x 146 Instrukcja

5 Października 2024
Celexon

Celexon Statief Economy (4:3) 176 x 132 Instrukcja

5 Października 2024
Celexon

Celexon Economy (4:3) 158 x 118 Instrukcja

5 Października 2024
Celexon

Celexon Ultramobil Professional Instrukcja

4 Października 2024
Celexon

Celexon Statief Economy Instrukcja

4 Października 2024
Celexon

Celexon Economy (4:3) 133 x 100 Instrukcja

4 Października 2024