Instrukcja obsługi Da-Lite Dual Format Imager 38063EV

Da-Lite Ekran projekcyjny Dual Format Imager 38063EV

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Da-Lite Dual Format Imager 38063EV (21 stron) w kategorii Ekran projekcyjny. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/21
INSTRUCTION BOOK FOR
Dual Format Imager
2
Tools Required for Installation
Important Safety Instructions
When using your video equipment, basic safety
precautions should always be followed, including the
following:
1. Read and understand all instructions before using.
2. Close supervision is necessary when any appliance is
used by or near children. Do not leave appliance
unattended while in use.
3. Care must be taken as burns can occur from touching
hot parts.
4. Do not operate appliance with a damaged cord or if the
appliance has been dropped or damaged - until it has
been examined by a qualiied serviceman.
5. To reduce the risk of electric shock, do not immerse this
appliance in water or other liquids.
6. The use of an accessory attachment not recommended
by the manufacturer may cause a risk ofire, electric
shock, or injury to persons.
Save These Instructions
Pre-Installation
Have space for this unit available on alat clean surface such as
a large table orloor. The work area should be larger than the
frame size. If the loor is used, clean papers should be spread to
keep all dirt from the Pro-Trim surfaces.
1/8" and 5/64"
Allen Wrenchs
Tape Measure
Carpenter's Level Electric Screw Gun Utility Knife
3
1. The frame will arrive in two separate cardboard boxes. One
box will be very long and will house the top & bottom pieces.
The smaller cardboard box will house the side frame pieces,
hanger hardware, hardware required to put frame together
and the wall switch.
2. To open the boxes there is a sidelap that is taped down the
length of the box. It will be labeled OPEN THIS SIDE (Figure 1).
Carefully cut tape down the length of the box with a utility
knife and fold box open. You will have to tear hard on the
ends as it is stapled on the ends.
3. Inside each box the frame pieces will be individually paper
wrapped and taped. Remove all paper from pieces.
CAUTION: DO NOT USE A UTILITY KNIFE TO REMOVE
PAPER FROM PIECES
ATTENTION: N'UTILISEZ PAS DE COUTEAU UTILITAIRE
POUR RETIRER LE PAPIER DES PCES.
4. Remove all paper and styrofoam blocks from top frame
assembly after unwrapping.
1. In the hardware bag, you will receive (12) #10 x .375" long hex
button head screws and (4) #10 x .500" long hex button head
screws required for frame assembly.
2. Lay frame pieces out on loor or table as shown in Figure 1.
The top frame assembly has the roller and motor assembly
attached to it. The side frames are the two shorter pieces.
Watch side piece to make sure oriented properly. The sides
have two riv nuts used for roller mounting brackets that
should face toward the top frame piece.
Unpackaging the Frame:
Frame Assembly
Rivnut
Make sure slat is
guided in to the
channel
Figure 1
Top of Frame
Bottom of Frame
Right of
Frame
Left of
Frame


Specyfikacje produktu

Marka: Da-Lite
Kategoria: Ekran projekcyjny
Model: Dual Format Imager 38063EV

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Da-Lite Dual Format Imager 38063EV, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Ekran projekcyjny Da-Lite

Instrukcje Ekran projekcyjny

Najnowsze instrukcje dla Ekran projekcyjny