Instrukcja obsługi Da-Lite Da-Tex (Rear)

Da-Lite Ekran projekcyjny Da-Tex (Rear)

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Da-Lite Da-Tex (Rear) (8 stron) w kategorii Ekran projekcyjny. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: info@da-lite.com
Instruction Book for
TENSIONED ADVANTAGE® ELECTROL®
The Da-Lite Difference.
1
1. Remove 2 screws to open junction box.
2. Hang case and attach to support structure with threaded rod. See suggested methods of installation on page 5.
3. Tighten bolts until trim flange is flush with ceiling.
NOTE: For proper operation, screen assembly must be level after installation.
4. Install electrical connections that applies to your unit. Make sure to review the wiring diagram for proper hook up.
NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.
5. Replace junction box cover and secure with 2 screws.
6. If screen and case are purchased together, remove slat retainer brackets from the screen case and back of slat.
PRE-INSTALLATION
1. Carefully unpack case from shipping carton. DO NOT unpack fabric and roller assembly yet.
2. Make sure to recheck measurement of case for proper installation clearance.
3. Remove any protective foam or tape from case.
CASE INSTALLATION
IMPORTANT SAFETY INSTRUCTIONS
When using your video equipment, basic safety precautions should always be followed, including the
following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance
should be used. Cords rated for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this appliance. Contact an authorized
service dealer when repair work is required. Incorrect reassembly can cause electric shock when
the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the manufacturer may cause a risk of
fire, electric shock, or injury to persons.
SAVE THESE INSTRUCTIONS
If your screen was shipped with the motor and roller already installed, proceed to step 6.
1. Remove access door. First, remove the 2 screws from the ends. Be sure to support the door during this
step to avoid injury. Then lift the door slightly and pull away from the edge of the case.
2. Carefully unpack screen and roller assembly. Leave packing paper on roller.
3. To install screen and roller assembly, insert the motor end into the motor mount bracket as shown in Fig. 1.
4. Loosen (but do not remove) two 1/4-20 nuts securing pin end bracket (stage left) to the case housing. Slide the
bracket towards the end of the case. Insert the motor end square shaft into the motor end bracket and secure with
the clip.Insert the tip of the roller pin end into the bracket and position. Tighten the 1/4-20 nuts securely.
5. Complete electrical hook-up by snapping motor wire connector into case connector.
6. Carefully remove paper and tape from roller assembly. use a knife or sharp object to cut tape; you will DO NOT
damage the screen.
7. Test installation by running screen up and down a few times. Be prepared to stop screen. Standard Duty Cycle: 1
MIN. ON / 3 MIN. OFF.
8. Re-install access door. Procedure is reverse of removal (step 1).
SCREEN AND ROLLER ASSEMBLY INSTALLATION
2
ADVANTAGE® ELECTROL® INSTALLATION
7-3/4"
6-1/16" 3/8" THREADED ROD
(NOT INCLUDED)
ATTACHED TO
MOUNTING BRACKET
SELF-TRIMMING
FLANGE
6-3/8"
7-3/4"
FINISHED
CEILING
8"
6.42"
3/8" THREADED ROD
(NOT SUPPLIED)
HANGER BRACKET
SEE DETAIL A
7.75"
DETAIL A
7.95"
3.41"
ELECTRICAL
JUNCTION BOX
MOTOR END
VARIABLE POSITION
MOUNTING BRACKET
AUDIENCE
SIDE
6-1/16"
6-7/16"
FIGURE 1

Specyfikacje produktu

Marka: Da-Lite
Kategoria: Ekran projekcyjny
Model: Da-Tex (Rear)

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Da-Lite Da-Tex (Rear), zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ekran projekcyjny Da-Lite

Da-Lite

Da-Lite Model C With CSR Instrukcja

7 Października 2024
Da-Lite

Da-Lite Designer Manual 76456MO Instrukcja

6 Października 2024
Da-Lite

Da-Lite Cinema Vision Instrukcja

1 Października 2024
Da-Lite

Da-Lite Model C 83401 Instrukcja

29 Września 2024
Da-Lite

Da-Lite Model B Instrukcja

27 Września 2024
Da-Lite

Da-Lite Perm-Wall 78676 Instrukcja

26 Września 2024
Da-Lite

Da-Lite DescenderPro 29788LS Instrukcja

17 Września 2024
Da-Lite

Da-Lite Flex Plex 29529 Instrukcja

12 Września 2024
Da-Lite

Da-Lite Da-Tex (Rear) Instrukcja

11 Września 2024
Da-Lite

Da-Lite Dual Format Imager 38063EV Instrukcja

11 Września 2024

Instrukcje Ekran projekcyjny

Najnowsze instrukcje dla Ekran projekcyjny

Optoma

Optoma DS-3120PMG Instrukcja

11 Października 2024
EPV

EPV PGF106WH1-A4K Instrukcja

8 Października 2024
EPV

EPV PGF84WH1 Instrukcja

8 Października 2024
Celexon

Celexon Ultramobile Plus Professional 194 x 146 Instrukcja

5 Października 2024
Celexon

Celexon Statief Economy (4:3) 176 x 132 Instrukcja

5 Października 2024
Celexon

Celexon Economy (4:3) 158 x 118 Instrukcja

5 Października 2024
Celexon

Celexon Ultramobil Professional Instrukcja

4 Października 2024
Celexon

Celexon Statief Economy Instrukcja

4 Października 2024
Celexon

Celexon Economy (4:3) 133 x 100 Instrukcja

4 Października 2024
Celexon

Celexon Ultramobile Plus Professional Instrukcja

4 Października 2024