Instrukcja obsługi Da-Lite Perm-Wall 78676

Da-Lite Ekran projekcyjny Perm-Wall 78676

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Da-Lite Perm-Wall 78676 (4 stron) w kategorii Ekran projekcyjny. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
INSTRUCTION BOOK FOR
Perm Wall Frame
2
Perm Wall Installation
The Perm Wall frame should be fastened to a wall. The frame is not designed for lying installations.
1. Assemble frame sections together by inserting plastic corner
brackets to tubes and securing the corners with #12 sheet
metal screws. If you have a larger jointed frame, insert steel
bracket on one section of frame into other section matching
the color code. Insert 1032 screw through tube and bracket
and fasten with wing nut.
NOTE: If the viewing surface is attached to the frame before
the frame is secured to the wall, the frame may bow.
2. Place bottom of frame at desired height on wall. Make sure
bottom is level. Drill through aluminum tubing every 18" to 24"
and fasten to wall with appropriate fastener (not supplied) for
type of wall construction.
NOTE: Use appropriate fastener for wall construction, i.e.
wood screws if wall behind frame is wood construction or
other appropriate fastener if dry wall or plaster or cement
block construction.
3. Make sure that sides are at 90 degrees or right angle to
bottom and fasten to wall in like manner. Next fasten top of
frame to wall in the same manner, making sure that the
center is the same distance from the bottom as it is at the
sides of frame. This is most important for proper surface it.
NOTE: If a center spreader is shipped with frame, insert
center spreader between the bottom and the top of frame as
a guide. This is most important to insure that the top and
bottom are equal distance apart across the entire top of
frame. Lack of care in this regard will result in poor it of
surface. Center spreader can be removed once top of frame
is fastened to the wall.
4. Carefully snap surface onto frame. This completes
the installation.
3
Cleaning
Da-Mat®, High Contrast Da-Mat®, Pearlescent, Cinema Vision,
High Contrast Cinema Vision, High Contrast Cinema Perf,
Audio Vision, High Contrast Audio Vision, Da-Tex® (Rear) and
Dual Vision surfaces can be cleaned as follows:
Using a white clean cloth (100% cotton preferred) that is
dampened with clear water, gently wipe the area in one direction.
Do not use a circular motion. Using a dry 100% cotton cloth,
wipe dry after each cleaning session. To clean a stubborn stain
or a sticky surface, use denatured alcohol (methanol or methyl
alcohol) following the same procedure as for water.
Corner Plastic Bracket
Frame
Tubing
#12 Sheet Metal
Screw
Detail View Of
Frame Corner
Color Coded
Bands To
Simplify
Assembly (For
Large Screens
With Width 96"
And Over)
Binding With
Snap Buttons
Precisely
Placed
Studs For
Snap
Buttons
Wing Nut Concealed
By Binding
Detail View Of
Frame Joint
Anodized
Aluminum Frame
Steel Bracket
Frame Tubing
Picture
Surface


Specyfikacje produktu

Marka: Da-Lite
Kategoria: Ekran projekcyjny
Model: Perm-Wall 78676

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Da-Lite Perm-Wall 78676, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Ekran projekcyjny Da-Lite

Instrukcje Ekran projekcyjny

Najnowsze instrukcje dla Ekran projekcyjny