Instrukcja obsługi Da-Lite Da-Snap
Da-Lite
Ekran projekcyjny
Da-Snap
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Da-Lite Da-Snap (8 stron) w kategorii Ekran projekcyjny. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: info@da-lite.com
Instruction Book for
DASNAP SCREEN
The Da-Lite Difference.
1
1. Unpack the frame parts from the carton. DO NOT
unroll the screen surface at this time.
2. Slide the frame pieces together at corners. (Note:
Frame assembly holes may not appear to fit properly
at the corners until all fasteners have been attached.
Once fasteners are attached, the frame corners will
be drawn in for a proper fit.) Secure frame pieces
with #10 screws provided. Do not tighten screws
until all are started, then tighten. See Figure 1.
NOTE: The frame pieces are labeled “top” and “bottom”.
Be sure the frame pieces are assembled according to the
labels. This will ensure the snap pattern on the frame and
screen surface will match.
FRAME ASSEMBLY
FIGURE 1. REAR VIEW
SNaP STuD
SIDE
#10 BLaCK SCREW
SIDE
TOP
BOTTOM
SNaP STuD
LARGE WALL BRACKET (47" LONG)
Quantities vary by screen size:
Screens 80" and smaller viewing width = 1
Screens over 80" to 96" viewing width = 2 QUANTITY INCLUDED __________
Screens over 96" viewing width = 3
Installation screws not included
SMALL WALL BRACKET (8" LONG)
Quantity of 1. Only for screens
80" and smaller viewing width QUANTITY INCLUDED __________
Installation screws not included
SNAP STUD
QUANTITY INCLUDED ________
#10 SCREW
QUANTITY INCLUDED ________
FRAME BRACKET
Quantities vary by screen size
Screens 80" and smaller viewing width = 3
Screens over 80" to 96" viewing width = 4
Screens over 96" viewing width = 6
QUANTITY INCLUDED ________________________________
HIGH POWER® FRAME BRACKET
Screens with High Power® viewing surface quantity = 2
Screens with 2-piece side frame rails quantity = 2
Screens 10' to 16' viewing width = 2
QUANTITY INCLUDED ________________________________
USE INSTALLATION
METHOD NUMBER __________
2
There are four methods of installation based on the size
of the screen and type of viewing surface. Measure the
width of the viewing area of your screen and refer to the
appropriate method of installation below. The wall
bracket diagram shows the type and quantity of bracket
that is supplied based on the size of the screen.
Method 1: Screens 80" and smaller in viewing width.
Method 2: Screens over 80" up to 96" in viewing width.
Method 3: Screens over 96" in viewing width.
Method 4: Any size screen with High Power® viewing
surface.
INSTALLATION
4. Attach the small wall bracket to the wall. Refer to
Figure 4 for proper orientation. Do not tighten the
screws completely. The bracket should slide up and
down easily.
5. Unroll the screen on a clean surface. Do not use
newspaper. The viewing side is rolled to the inside of
the roll. Place the frame over the screen surface, and
while lifting the frame with one hand, snap the
screen surface onto the frame with the other hand
while maintaining a steady pull on the surface.
6. Hang the screen on the brackets by hooking the
bottom of the frame onto the small wall bracket and
lift up until you can hook the top of the frame on the
top bracket. Push down on the frame to seat it on the
brackets. Refer to Figure 4.
OvERaLL hEIghT - 1-3/8"
OvERaLL
hEIghT
6"
2
LIFT
3
1
WaLL
1. Use the supplied #10 screws to attach three frame
brackets to the back of the frame as shown in Figure
2.
2. Secure the large wall bracket to wall studs at the
desired height. Make sure the bracket is level. The
top of the frame will be 1/8" above the top of the wall
bracket when mounted. You will need at least 5/8"
clearance above the bracket to hang the screen.
3. To install the small wall bracket, you must measure
the overall height of the screen frame and subtract
1-3/8". Using that dimension, measure down from the
top edge of the large wall bracket and mark the wall
for two screw holes. The holes should be centered
within the frame and 6" apart. Refer to Figure 3.
METHOD 1 (SCREENS 80" AND SMALLER IN
VIEWING WIDTH)
FIGURE 2
FRaME BRaCKETS
3-PIECES
#10 SCREWS
6-PIECES
LaRgE WaLL
BRaCKET
1-PIECE
SMaLL WaLL BRaCKET
1-PIECE
METHOD 1 (SCREENS 80" AND SMALLER IN
VIEWING WIDTH)
FIGURE 3
FIGURE 4
Specyfikacje produktu
| Marka: | Da-Lite |
| Kategoria: | Ekran projekcyjny |
| Model: | Da-Snap |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Da-Lite Da-Snap, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Ekran projekcyjny Da-Lite
7 Października 2024
6 Października 2024
1 Października 2024
29 Września 2024
27 Września 2024
26 Września 2024
17 Września 2024
12 Września 2024
11 Września 2024
11 Września 2024
Instrukcje Ekran projekcyjny
- Ekran projekcyjny Kodak
- Ekran projekcyjny Draper
- Ekran projekcyjny Pyle
- Ekran projekcyjny Oregon Scientific
- Ekran projekcyjny Optoma
- Ekran projekcyjny Duronic
- Ekran projekcyjny GPX
- Ekran projekcyjny AV:link
- Ekran projekcyjny Luxburg
- Ekran projekcyjny Elite
- Ekran projekcyjny Elite Screens
- Ekran projekcyjny EluneVision
- Ekran projekcyjny Celexon
- Ekran projekcyjny Lumene
- Ekran projekcyjny Stewart
- Ekran projekcyjny Avers
- Ekran projekcyjny Elite ProAV
- Ekran projekcyjny EPV
Najnowsze instrukcje dla Ekran projekcyjny
11 Października 2024
8 Października 2024
8 Października 2024
5 Października 2024
5 Października 2024
5 Października 2024
4 Października 2024
4 Października 2024
4 Października 2024
4 Października 2024