Instrukcja obsługi Blustream CMX42AB

Blustream router CMX42AB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Blustream CMX42AB (9 stron) w kategorii router. Ta instrukcja była pomocna dla 27 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/9

CMX42AB USER MANUAL

contact support@blustream.co.uk / support@blustream.com.au

User Manual

CMX42AB

Our Contractor CMX42AB 4K HDMI matrix features HDMI 2.0 chipsets with HDCP 2.2 support, allowing

distribution of four HDMI sources to two displays. This enables all sources to be viewed seamlessly as

required within a matrix configuration. The unit transmits all HDMI resolutions up to and including 4K 60Hz

4:4:4/HDR. The 4-Way matrix also includes audio breakout and EDID management.

Introduction

Key Features:

• Features 4x HDMI inputs which can be independently routed up to two HDMI outputs

• Supports 4K UHD video (up to 4K @60Hz 4:4:4/HDR)

• Supports all industry standard video resolutions including VGA-WUXGA and 480i-4K

• Supports all known HDMI audio formats including Dolby TrueHD, Dolby Atmos, Dolby Digital Plus and

DTS-HD Master Audio transmission

• HDMI audio breakout to associated output analogue L/R audio and coaxial digital outputs concurrently

• IR routing

• Supplied with Blustream 5V IR receivers and emitters

• Control via front panel, IR and RS-232

• 3rd Party drivers available for all major home control brands

• Advanced EDID management

• HDCP 2.2 compliant

CMX42AB USER MANUAL

02 www.blustream.co.uk

Panel Description

Front Panel:

IR receiver window for matrix control

Power LED indicator

HDMI output selection buttons 1-2. Press to scroll through source inputs per HDMI output

1 2

Rear Panel:

The EDID configuration can be altered using the

dip-switches located on the rear panel of the

matrix.

Please see adjacent table for EDID settings.

Note: You must power-cycle the HDMI switcher

aer changes have been made in order for the EDID

settings to update.

Adjusting The EDID Settings

EDID Dip-switches

[DIP]=0000: HDMI 1080p@60Hz, Audio 2ch PCM

[DIP]=0001: HDMI 1080p@60Hz, Audio 5.1ch PCM/DTS/DOLBY

[DIP]=0010: HDMI 1080p@60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD

[DIP]=0011: HDMI 1080i@60Hz, Audio 2ch PCM

[DIP]=0100: HDMI 1080i@60Hz, Audio 5.1ch PCM/DTS/DOLBY

[DIP]=0101: HDMI 1080i@60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD

[DIP]=0110: HDMI 4K@60Hz 4:2:0+4K@30Hz 4:4:4, Audio 2ch PCM

[DIP]=0111: HDMI 4K@60Hz 4:2:0+4K@30Hz 4:4:4, Audio 5.1ch PCM/DTS/DOLBY

[DIP]=1000: HDMI 4K@60Hz 4:2:0+4K@30Hz 4:4:4, Audio 7.1ch PCM/DTS/DOLBY/HD

[DIP]=1001: HDMI 4K@60Hz 4:4:4, Audio 2ch PCM

[DIP]=1010: HDMI 4K@60Hz 4:4:4, Audio 5.1ch PCM/DTS/DOLBY

[DIP]=1011: HDMI 4K@60Hz 4:4:4, Audio 7.1ch PCM/DTS/DOLBY/HD

[DIP]=1100: DVI 1280x1024@60Hz, Audio None

[DIP]=1101: DVI 1920x1080@60Hz, Audio None

[DIP]=1110: DVI 1920x1200@60Hz, Audio None

[DIP]=1111: Soware Control EDID

EDID Dip-switches

14139 10 12

6 7

IR output - 3.5mm mono jack provides routed IR emitter

output for discrete control of sources

IR input - 3.5mm stereo jack provides zone specific

routed IR receiver input

Coaxial digital audio output - RCA (SPDIF)

Analog L/R audio output - 3.5mm stereo audio jack,

Supports 2 channel PCM only

Power on/o switch

EDID DIP switch - Used to manage the video and audio

resolution output by the connected source device.

HDMI inputs - connect to HDMI source devices

HDMI outputs - connect to HDMI display devices

RS-232 Serial port - For control of switcher by third party

control devices

IR control - IR input for switcher control. Connect 5V Blus-

tream IR receiver

Power port - Use included 12V/2A DC power adaptor

510

CMX42AB USER MANUAL

contact support@blustream.co.uk / support@blustream.com.au

RS-232 Serial Control

BLUSTREAM RS-232 REMOTE CONTROL

CONSOLE

PIN Assignment PIN Assignment

1 NC 1 NC

2 2 Tx Rx

3 3 Rx Tx

4 NC 4 NC

5 GND 5 GND

6 NC 6 NC

7 NC 7 NC

8 NC 8 NC

9 NC 9 NC

Baud Rate: 57600 bps

Data Bit: 8-bit

Parity: None

Stop Bit: 1-bit

Flow Control: None

Audio Breakout

The Matrix includes audio breakout from the selected HDMI input to associated analogue L/R audio and coaxial digital outputs.

Extracted audio will be concurrent with the corresponding HDMI video output. Note: Source input must be PCM 2ch audio for

analogue audio outputs to work. The Matrix does not down-mix multichannel audio signals.

Coaxial digital output - Output 1

Analogue fixed line level output 3.5mm stereo jack - Output 1

1 2

The Matrix can be controlled via 9-pin serial RS-232 cable.

RS-232 COMMAND DESCRIPTION

? Print Help Information

HELP Print Help Information

STATUS Print System Status And Port Status

PON Power On, System Run On Normal Sta

POFF Power O, System Run On Power Save State

IRON/OFF Set System IR Control On Or O

KEYON/OFF Set System KEY Control On Or O

BEEPON/OFF Set Onboard Beep On Or O

LEDON/OFF Set Front Panel LED Always On

or Auto Turn O in Power On State

RESET Reset System To Default Setting (Type “Yes” To Confirm, “No” To Discard)

OUTxxFRON/OFF

OUTxxFRyy

Set OUTPUT:xx On or O

Set OUTPUT:xx From INPUT:yy

xx=00: Select All OUTPUT Port

xx=[01...02]: Select One OUTPUT Port

yy=[01...04]: Select One INPUT Port

EDIDxxCPyy

EDIDxxDFzz

xx=00: Select All INPUT Port

xx=[01...04]: Select One INPUT Port

yy=[01...02]: Select One OUTPUT Port

zz=00: HDMI 1080p@60Hz, Audio 2CH PCM

zz=01: HDMI 1080p@60Hz, Audio 5.1CH DTS/DOLBY

zz=02: HDMI 1080p@60Hz, Audio 7.1CH DTS/DOLBY/HD

zz=03: HDMI 1080i@60Hz, Audio 2CH PCM

zz=04: HDMI 1080i@60Hz, Audio 5.1CH DTS/DOLBY

zz=05: HDMI 1080i@60Hz, Audio 7.1CH DTS/DOLBY/HD

zz=06: HDMI 1080p@60Hz/3D, Audio 2CH PCM

zz=07: HDMI 1080p@60Hz/3D, Audio 5.1CH DTS/DOLBY

zz=08: HDMI 1080p@60Hz/3D, Audio 7.1CH DTS/DOLBY/HD

zz=09: HDMI 4K@30Hz 4:4:4, Audio 2CH PCM

zz=10: HDMI 4K@30Hz 4:4:4, Audio 5.1CH DTS/DOLBY

zz=11: HDMI 4K@30Hz 4:4:4, Audio 7.1CH DTS/DOLBY/HD

zz=12: DVI 1280x1024@60Hz, Audio None

zz=13: DVI 1920x1080@60Hz, Audio None

zz=14: DVI 1920x1200@60Hz, Audio None

zz=15: User EDID 1

zz=16: User EDID 2

zz=17: GUI Download EDID

zz=18: HDMI 4K@60Hz 4:2:0, Audio 2CH PCM

zz=19: HDMI 4K@60Hz 4:2:0, Audio 5.1CH DTS/DOLBY

zz=20: HDMI 4K@60Hz 4:2:0, Audio 7.1CH DTS/DOLBY/HD

zz=21: HDMI 4K@60Hz 4:4:4, Audio 2CH PCM

zz=22: HDMI 4K@60Hz 4:4:4, Audio 5.1CH DTS/DOLBY

zz=23: HDMI 4K@60Hz 4:4:4, Audio 7.1CH DTS/DOLBY/HD

Specyfikacje produktu

Marka:	Blustream
Kategoria:	router
Model:	CMX42AB
Kolor produktu:	Czarny
Wysokość produktu:	47 mm
Szerokość produktu:	255 mm
Głębokość produktu:	115 mm
W zestawie pilot zdalnego sterowania:	Tak
Podręcznik użytkownika:	Tak
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Certyfikaty:	FCC, CE, RoHS, CAN ICES-3 (B)/NMB-3(B)
Gniazdko wyjścia DC:	Tak
Zasilacz sieciowy:	Tak
Typ HD:	4K Ultra HD
Napięcie operacyjne:	12 V
Zakres temperatur (eksploatacja):	0 - 40 °C
Przewody:	Podczerwień
Waga wraz z opakowaniem:	1600 g
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-20 - 60 °C
Prąd wyjściowy:	2 A
Rodzaj opakowania:	Pudełko
Maks. rozdzielczość:	- px
Maksymalna częstotliwość odświeżania:	60 Hz
Wersja HDMI:	2.0
HDCP:	Tak
Możliwości montowania w stelażu:	Tak
Interfejs do odtwarzania wideo:	2x HDMI
Technologia dolby:	DTS-HD Master Audio, DTS:X, Dolby Atmos, Dolby TrueHD
Obsługiwane typy kabli:	Coaxial, HDMI
Rodzaj portu wideo:	HDMI
Ilość portów wideo:	6
Ilość portów audio:	4