Instrukcja obsługi American DJ Mega Bar RGBA

American DJ Maszyna efektów Mega Bar RGBA

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla American DJ Mega Bar RGBA (14 stron) w kategorii Maszyna efektów. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/14

User Instructions

Mega Bar RGBA Introduction

ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 2

1/13

Unpacking: Thank you for purchasing the Mega Bar RGBA by ADJ

Products, LLC. Every Mega Bar RGBA has been thoroughly tested and

has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping.

If the carton appears to be damaged, carefully inspect your xture for

any damage and be sure all accessories necessary to operate the unit

has arrived intact. In the case damage has been found or parts are

missing, please contact our toll free customer support number for fur-

ther instructions. Do not return this unit to your dealer without rst con-

tacting customer support.

Introduction: The ADJ Mega Bar RGBA is a rechargeable lithium bat-

tery powered, DMX intelligent, LED bar fixture. This unit give you the

freedom to set up your fixture where ever you wish without the restric-

tions of power. The built-in battery will keep charge for up to 8 hours

(full on) from a full, single charge. This xture can be used in a stand

alone mode or connected in a Master/Slave conguration. This wash

has ve operating modes: Sound Active mode, Auto mode, RGB mode,

Static Color mode, and DMX control mode.

Customer Support: ADJ Products, LLC provides a customer support

line, to provide set up help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.adj.com for any comments or sugges-

tions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.

Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: support@adj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

Mega Bar RGBA Safety Precautions

ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 4ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 3

• Mulit-Colors

• Six Operating Modes

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• 3-Pin DMX Connection

• Seven DMX Modes: 4 Channel Mode, 6 Channel Mode, 7 Channel

Mode, 9 Channel Mode, 10 Channel Mode, 18 Channel Mode, and

34 Channel Mode.

• ADJ RFC compatiable (Not Included)

• Power Cord Daisy Chain (See page 23)

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken. Do not attempt to remove or break off the ground

prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by

t he manufacturer. See page 23 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (inclu-

d ing ampliers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Mega Bar RGBA Warranty Registration

Mega Bar RGBA Features

The 3 Mega Bar RGBA carries a year limited warranty. Please fill out

the enclosed warranty card to validate your purchase. All returned

service items whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. The R.A. number

must be clearly written on the outside of the return package. A brief

description of the problem as well as the R.A. number must also be

written down on a piece of paper included in the shipping carton. If

the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain a R.A. number by contacting our

customer support team on our customer support number. All pack-

ages returned to the service department not displaying a R.A. number

on the outside of the package will be returned to the shipper.

The unit should be mounted using a mounting clamp (not provided),

afxing it to the mounting bracket that is provided with the unit.

Always ensure that the unit is rmly xed to avoid vibration and slip-

ping while operating. Always ensure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10

times the unit’s weight. Also, always use a safety cable that can hold

12 times the weight of the unit when installing the xture.

The equipment must be installed by a professional, and it must be

installed in a place where it is out of the reach of people’s grasp.

Mega Bar RGBA Installation

ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 5 ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 6

P -ower Supply: The ADJ Mega Bar RGBA contains a automatic volt

age switch, which will auto sense the voltage when it is plugged into

the power source. With this switch there is no need to worry about the

correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that trav-

els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-

minals located on all DMX fixtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a single

controller, as long as all xtures and the controller are DMX compli-

ant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order

in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address

of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The Mega Bar RGBA can be controlled via DMX-512 protocol. The

Mega Bar RGBA has 7 DMX channel modes, please see pages 9-10

for the different modes. The DMX address is set on the back panel of

the Mega Bar RGBA. Your unit and your DMX con-

troller require a standard 3-pin XLR connector for

data input and data output (Figure 1). We recom-

mend Accu-Cable DMX cables. If you are making

your own cables, be sure to use standard 110-120

Ohm shielded cable (This cable may be purchased

at almost all pro lighting stores). Your cables should

be made with a male and female XLR connector on

either end of the cable. Also remember that DMX cable must be daisy

chained and cannot be split.

Mega Bar RGBA Set Up

Figure 1

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

Mega Bar RGBA Set Up

DMX512 IN

3-PIN XLR

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket

XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

Termination educes signalr errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture. Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Specyfikacje produktu

Marka:	American DJ
Kategoria:	Maszyna efektów
Model:	Mega Bar RGBA

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z American DJ Mega Bar RGBA, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Maszyna efektów American DJ

American DJ Mega Flat Pak 8 Plus Instrukcja

28 Sierpnia 2024

American DJ Focus Spot 5Z Instrukcja

23 Sierpnia 2024

American DJ Fog Fury 2000 Instrukcja

22 Sierpnia 2024

American DJ VF400 Instrukcja

17 Sierpnia 2024

American DJ H2O IR Instrukcja

15 Sierpnia 2024

American DJ Focus Profile Instrukcja

9 Sierpnia 2024

American DJ 32 HEX Panel IP Instrukcja

6 Sierpnia 2024

American DJ ECO UV Bar Plus IR Instrukcja

5 Lipca 2024

American DJ Pinspot LED Instrukcja

4 Lipca 2024

American DJ Fog Storm 1700 Instrukcja

3 Lipca 2024

Instrukcje Maszyna efektów

Najnowsze instrukcje dla Maszyna efektów

Velleman vdl660rl Instrukcja

10 Października 2024

Valcom V-5580041A Instrukcja

8 Października 2024

Magmatic Magma Fog 1500IP-II Instrukcja

8 Października 2024

Magmatic PMDMX1 Instrukcja

8 Października 2024

Magmatic CRISP Instrukcja

8 Października 2024

Magmatic CRISP MAX Instrukcja

8 Października 2024

Magmatic SIDEWINDER Instrukcja

8 Października 2024

Magmatic JAVELIN Instrukcja

8 Października 2024

Magmatic MAGMA FOG 1500 IP Instrukcja

8 Października 2024

BeamZ BLAZE3500 Instrukcja

8 Października 2024