Instrukcja obsługi AKAI BTE-J10

AKAI Zatyczka do uszu BTE-J10

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AKAI BTE-J10 (32 stron) w kategorii Zatyczka do uszu. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/32
USER MANUAL
WIRELESS EARPHONES
MODEL: BTE-J10
EN-ENGLISH
TECHNICAL SPECIFICATIONS
SAFETY INFORMATION
Use earbuds while driving, please observe the national and regional regulation.
Please put all the equipment and accessories in places that cannot be touched by the child or pet,
which may cause suffocation and serious consequences.
Please don't use the product under too high or too low temperature environment. (Below -10
degree or above- 45 degree)
Extreme temperatures can cause deformations, reduce the charging capacity of the device, and
shorten the service life.
Do not use wet equipment or near liquid which can cause severe damage to equipment.
Please do not use wet hand operating equipment, equipment damage caused by water does not
under the warranty scope.
If the earbuds play at high volume for a long time, your hearing may be hurt and suggest using
the lowest volume of the phone.
PACKAGE CONTENT
USER MANUAL
EARPHONES
TYPE-C CHARGING CABLE
Model number
BTE- 0 J1
Chipset
JL AC6983D
Bluetooth Version
Bluetooth V5.0+EDR
Bluetooth Frequency
2.400-2.485GHz
Audio decoding
SBC/AAC
Profiles supported
HFP A2DP AVRCP AVDTP GAP SDP
Weight
44g
Base Unit Dimensions
73x37x28mm
Speaker Unit size
10mm
Charging Input
5V 0mA 50
Microphone Sensitivity
－42±3dB
Frequency Response
20Hz-20000Hz
Built in Battery type (Earbuds)
Lithium 40 mAh 3.7V
Built in Battery type(Base Unit)
Lithium 0mAh 3.7V 30
Standby Time(Earbuds)
240 Hours
Playing Time(Earbuds)
4.0 hours (Approx.)
Charge Time (Earbuds)
1.5 Hours (Approx.)
Charge Time (Charging case)
1.5 Hour (Approx.)
Bluetooth Range
10 meters (open space with no obstacle)
Bluetooth Transmission power
≦ 10 dBm
Supported system
iOS system & Android system
AWS OPERATION INSTRUCTIONS
Initial Earbuds Set Up/Pairing
Step 1: Once both earbuds are removed from the case they will automatically power on, blue
light on each earbud will be on.
Step 2: Once the earbuds are turned on wait for the prompt “DuDu”, this confirms that the
earbuds are synced. Once pairing the 2 earbuds, there will be no light flash in the left earbud but
a blue and red light will start to flash in the right earbud.
Step 3: Go to the Bluetooth connection list on your smart phone “BTE-J10” Bluetooth name. Click
to connect. Both earbuds will now flash indicating that the earbuds are connected to the
Bluetooth device.
Auto Power On: Once both earbuds are removed from the case they will automatically power on,
a blue light will start to flash slowly in the left earbud, and a blue and red light will start to flash in
the right earbud, that means the connection process will start.
(Note: The case must be charged frequently in order for the earbuds to automatically power on.
If the case is not charged, the earbuds can be manually turned on.)
Manual Power On: Press and hold the main button on the and earbud at the same time for
about 3 seconds to power on. The blue light will begin to flash on the earbuds followed by a
“Power On” message through the earbuds.
Auto Power Off: Place the earbuds back into the case and close the lid. Once they are put into
the case, they will automatically power off and enter into the charged state when a red light
flashing on each earbud.
Manual Power Off: Press and hold the main button on the and earbud at the same time for
about 3 seconds. The red light will begin to flash on the earbuds followed by a “Power Off”
message through the earbuds.
Music Play/Pause Short press button play or pause music playing. : or to
Volume Up/Down Double press the main button earbud to volume up Double press the : of .
main button of earbud to volume down.
Music Next/Previous: Press the main button 3 times earbud to go to the next song. Press of
the main button 3 times earbud to go to the previous song. of

Specyfikacje produktu

Marka: AKAI
Kategoria: Zatyczka do uszu
Model: BTE-J10

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AKAI BTE-J10, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Zatyczka do uszu AKAI

AKAI

AKAI BTE-J10 Instrukcja

3 Stycznia 2025
AKAI

AKAI BTE-J20ANC Instrukcja

2 Stycznia 2025
AKAI

AKAI BTE-W300ENC Instrukcja

2 Stycznia 2025
AKAI

AKAI BTE-W200F Instrukcja

2 Stycznia 2025

Instrukcje Zatyczka do uszu

Najnowsze instrukcje dla Zatyczka do uszu

JBL

JBL Endurance Race 2 Instrukcja

5 Stycznia 2025
JBL

JBL Tune Beam 2 Instrukcja

5 Stycznia 2025
JBL

JBL Tune Flex 2 Instrukcja

5 Stycznia 2025
JBL

JBL Wave Buds 2 Instrukcja

5 Stycznia 2025
JBL

JBL Wave Beam 2 Instrukcja

5 Stycznia 2025
JBL

JBL Wave Flex 2 Instrukcja

5 Stycznia 2025
Audio-Technica

Audio-Technica ATH-CC500BT2 Instrukcja

5 Stycznia 2025
Audio-Technica

Audio-Technica ATH-CKS50TW2 Instrukcja

5 Stycznia 2025
Prixton

Prixton TWS163 Wood Instrukcja

5 Stycznia 2025
JVC

JVC HA-NP40T Instrukcja

4 Stycznia 2025