Instrukcja obsługi WyreStorm TX-SW-IW-0201

WyreStorm nieskategoryzowany TX-SW-IW-0201

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla WyreStorm TX-SW-IW-0201 (4 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

2x1 HDMI/VGA over HDBaseT™ Auto-Switching 2-Gang

In Wall Transmitter (100m/328ft)

TX-SW-IW-0201 Quickstart Guide

In the Box

1 x TX-SW-IW-0201 HDBaseT Wall Plate Transmitter

1 x 3-pin Plug-in Phoenix Connector

2 x 2pin-plug-in phoenix connectors

1 x Decorative Wall Plate with 4 screws

4 x 6-32x20mm Installation Screws

Basic Wiring Diagram

Installation

IMPORTANT! Do not connect or disconnect (hot plug) the HDMI, or

HDBaseT connections while the transmitter is powered on. Doing so may

cause damage to the transmitter or connected devices.

1. Verify that all items are included in the packaging per the list under

the section.In the Box

2. Run a Cat5/5e/6 cable from the transmitter location to the receiver

location. Terminate the cable per the section and HDBaseT Wiring

connect to the on the transmitter.HDBT Out

3. (Optional) Terminate an IR emitter or cable per the section IR Wiring

and connect to the on the transmitter. Place the IR emitter IR Out

onto the source device near the IR receiver or connect to an IR port

on the source.

4. (Optional) Terminate a cable per the section and RS-232 Wiring

connect to the RS-232 pass-through on the transmitter. Connect the

opposite end to a port on a control system.

5. Connect the opposite end of the HDBaseT cable to a WyreStorm

HDBaseT receiver, switcher, or 3rd party display device with built-in

HDBaseT receiver. Power on the receiver.

6. (Optional) If power for the transmitter is not being supplied by the

receiver via PoH, connect a 12V DC 1A power supply (not included)

to the connection on the transmitter. See Power In Power Supply

Wiring.

7. Install the TX-SW-IW-0201 in a dual-gang wall box located near the

source.

8. Connect up to 2 sources to the transmitter.

• Connect a VGA source to the VGA In on the transmitter.

• Connect an HDMI source to the on the transmitter using HDMI In

an HDMI cable from a high quality brand such as WyreStorm

Express.

9. Power on the HDBaseT receiver or connect the power supply to an

AC outlet.

A PoH compatible HDBaseT transmitter with VGA & HDMI inputs, tting into a decora 2-Gang wall box.

TX-SW-IW-0201 Quickstart Guide | 150828

North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343

support@wyrestorm.com

1 of 4

KEY

HDMI

HDBaseT Cat5e/6

IR TX and RX

Analog Video (VGA)

Analog Audio

HDMI from Source

VGA from Source

Audio from Source

IR Out to Source

HDBaseT Cat5e/6

HDMI to

Display

IR TX to Display

IR RX (IR to Transmitter)

TX-SW-IW-0201 Front (with wall-plate)

TX-SW-IW-0201 Rear

HDMI Source

VGA Source

4K HDMI Display

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

TX-SW-IW-0201 Quickstart Guide | 150828

North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343

support@wyrestorm.com

2 of 4

Front Panel Rear Panel

HDMI IN and HDMI LED

19-pin type A HDMI female digital

video/audio input: Supports HDMI

and DVI/D (requires adapter-not

included). Limited to 297MHz pixel

clock. LED illuminates when HDMI

source is selected.

AUDIO IN

3.5 mm (1/8 in) Stereo Analog

Audio:

Connect to audio output of device

connected to VGA input.

VGA IN and VGA LED

15-pin VGA VESA (D-SUB 15):

Connect to D-SUB 15 VGA output

of a device such as a computer.

LED illuminates when VGA source is

selected.

EDID Settings

3 Position Dipswitch (Under

Faceplate):

Used to set EDID to correct

resolution conicts between the

source and the display.

See EDID Settings.

HDCP LED

Solid: Audio and Video signal is

HDCP protected.

Flashing: Audio and Video signal is

not HDCP protected.

O: No Audio and Video signal.

LINK LED

Solid: Link to receiver has been

established.

Flashing: Link to receiver has not

been established.

SELECT Press to switch between the VGA

and HDMI source inputs.

IR Sensor

30-55kHz IR Receiver.

Receives an IR signal from hand-

held remote or asher that is

transmitted to the remote display via

HDBaseT.

POWER IN

2-pin Screw Down Phoenix

Connector

(Optional) Connect to a 12V DC 1A

power supply (not included). Do not

use when powering transmitter via

PoH. See .Power Supply Wiring

ETHERNET

8-pin RJ-45 female

Connect to a router or switch to

supply Ethernet to remote location.

RS-232

3-pin Screw Down Phoenix

Connector

Used to send RS-232 signals to

the remote display location via

HDBaseT.

See RS-232 Wiring.

HDBT OUT

8-pin RJ-45 female

Connect to an HDBaseT receiver.

See for wiring HDBaseT Wiring

details.

IR OUT

2-pin Screw Down Phoenix

Connector

Used to send IR signals sent from

the remote display location via

HDBaseT to a device (source)

located near the transmitter.

See .IR Wiring

TX-SW-IW-0201 Quickstart Guide | 150828

North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343

support@wyrestorm.com

3 of 4

Wiring and Connections

HDBaseT Wiring

Wiring for HDBaseT follows the EIA T568B standard.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables,

and electrical or environmental interference can have an adverse eect

on HDBaseT transmission limiting performance. Steps should be taken

to minimize these factors (or remove completely) during installation for

best results.

• While similar in nature, the HDBaseT protocol is dierent than Ethernet

and voltages provided for PoH can be higher than those provided by

PoE. For this reason, never connect an HDBaseT link to an Ethernet

router or switch to avoid damaging the connected devices.

Supported Video Resolutions

The type of category cable used and the distance between the transmitter

and receiver can restrict the available video resolution.

Cable Type Range Supported Resolution

Cat5/5e/6

100m/328ft 1080p @ 60Hz 36bit

70m/230ft 3840 x 2160 @ 30Hz 4:4:4

Cat6a 100m/328ft

1080p @ 60Hz 36bit

1080p @ 60Hz 48bit

1080p @ 60Hz 3D

3840 x 2160 @ 30Hz 4:4:4

Note: When connected to a class B HDBaseT receiver, the

supported resolution is limited to 70m/230ft 1080p.

IR Wiring

Connection for an IR emitter or cable to control the local source use a

2-pin Screw Down Phoenix connector.

RS-232 Wiring

Connection for RS-232 pass-through to the display at the remote

location uses a 3-pin Screw Down Phoenix connector. The connector

type and pinout on the control system may vary, refer to the 3rd party

manufacturer’s instructions for details.

Power Supply Wiring

Power for the TX-IW-70-POH is supplied via PoH when connected to a

compatible HDBaseT receiver

When PoH is not available from the connected receiver, connect a 12V

DC 1A power supply (not included) using a 2-pin Screw Down Phoenix

Connector.

EDID Settings

EDID can be congured to resolve issues with video output on displays

that may not accept the maximum resolution available from the source.

Remove the faceplate from the TX-SW-IW-0201 and set the switches

based on the table below.

Pin 1

Pin 8

RJ-45 Connector (Gold Pins Facing Up)

Pin 2: Orange GreenPin 6:

Pin 1: White/Orange Pin 5: White/Blue

Pin 3: White/Green Pin 7: White/Brown

Pin 4: Blue Pin 8: Brown

1920x1080 (default) 1280x720

1280x800 1024x768

1920x1200 800x600

Specyfikacje produktu

Marka:	WyreStorm
Kategoria:	nieskategoryzowany
Model:	TX-SW-IW-0201
Kolor produktu:	Czarny
Wysokość produktu:	25 mm
Szerokość produktu:	108 mm
Głębokość produktu:	106.7 mm
Waga produktu:	190 g