Instrukcja obsługi WyreStorm TX-H2X-HDBT

WyreStorm nieskategoryzowany TX-H2X-HDBT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla WyreStorm TX-H2X-HDBT (4 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document version,

additional documentation, and conguration tools.

• Install the latest rmware to ensure that all features described in this

document are available during and after installation.

• Read through the Wiring and Connections section for important wiring

guidelines before creating or choosing premade cables.

Recommended Products

To take full advantage of the features of this matrix, WyreStorm recommends

the following products be used within this product.

RX-70-4K-SCL

Scaling receiver that allows for 4K and 2K screens to be used while

maintaining output of 4K.

RX-70-4K-ARC

HDCP 2.2 receiver with audio in to send audio from built in apps back to the

matrix.

RXF-300-4K

For use with TX-H2X-OM3 when duplex OM3 Multimode ber is required.

RXV-70-4K

For use when content too high in bandwidth for HDBaseT is required, such as

high-framerate HDR or 4:4:4/60.

In the Box

1x MX-1010-H2XC or MX-1616-H2XC

1x Handheld IR Remote

10/16x IR emitters

10/16x IR Broadband Receiver (30KHz to 50KHz)

1x IR Receiver (38Khz)

10/16x 3-pin phoenix to stereo RCA sockets

1x AC Power Cord with US Plug

1x AC Power Cord with UK Plug

1x AC Power Cord with EU Plug

1x USB to UART Serial Cable

2x 4U Rack Ears and Screws

1x Quickstart Guide (This Document)

Additional Information

Visit the product page on to download additional wyrestorm.com

documentation, control drivers, and conguration software.

MX-xxxx-H2XC Quickstart Guide | 180622

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the

installation process.

Basic Wiring Diagram

R -70-4K-ARCXV

R -300-4KXF

RX-70-4K

(Used for TX-H2X-HDMI

and TX-H2X-HDBT Cards)

KEY

HDMI

HDBaseT

Digital Audio

Analog Audio

Duplex OM3 Fiber

Blu-ray Player

Games Console

Satellite Box

Media Player

Custom 4K HDR Video Matrix with Audio Matrix & DSP

MX-1010-H2XC | MX-1616-H2XC Quickstart Guide

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its

entirety before running or terminating any wires to ensure proper operation and to avoid damaging the equipment.

HDMI/HDBaseT Wiring

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on HDMI

and Ethernet transmission limiting performance. Steps should be taken to

minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends using high quality HDMI cables such as

WyreStorm Express to ensure the highest content performance available.

• The type of category cable and length used can restrict the available video

resolution. While Cat5e can be used, WyreStorm recommends using Cat6

or higher to ensure the highest content performance available. See Video

Resolutions in the Specications table before determining cable type and

length.

IR TX/RX Wiring

IMPORTANT! IR TX/RX Guidelines

• WyreStorm IR ports function differently than standard IR ports. For this

reason only WyreStorm IR emitters and receivers can be used.

• WyreStorm IR emitter and receiver cables cannot be spliced as cutting

into the cables will short the shield. While an extension cable may be used,

WyreStorm assumes no responsibility for operation using an extension

cable.

• When connecting the IR TX to an IR connecting blocks or control system

with different plugs, a cable must be made following the IR TX Port Pinout

diagram.

• When connecting to an IR control system use the WyreStorm CAB-IR-LINK

cable. This cable compensates for differences between the WyreStorm RX

and the control systems TX connection. Visit the CAB-IR-LINK product page

for details.

IR TX Port Pinout

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX/Ext Port Pinout

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

RS-232 Wiring

Most control systems and computers are DTE where pin 2 is RX, this can vary

from device to device. Refer to the documentation for the connected device for

pin functionally to ensure that the correct connections can be made.

9 8 7 6

4 13 2

Outside of DB9 chassis port shown.

Unidnetiﬁed pins have no function and should

not be connected.

Pin 3: RX (Receive)

Pin 2: TX (Transmit)

Pin 5: GND (Ground)

Audio Wiring

Tip: Signal (+)

Shield: Ground/Return (-)

MX-xxxx-H2XC Quickstart Guide | 180622

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

EDID Settings

EDIDs can be congured to resolve issues with video output on displays that may not accept the maximum resolution available from the source.

• When set to Smart EDID (default) the matrix will scan all selected displays for the lowest resolution to dynamically adjust the source content to allow output

on 2K and 4K displays sharing the same source.

• When EDID Copy or a direct EDID is being used, SmartEDID is turned Off.

• Ensure that a display is connected and powered On to the selected output before copying EDIDs or the copy will fail. When this occurs, EDID will be set to

4K@30Hz 2ch.

• Power to the matrix must be cycled (Off/On) after changing dip switches in order for the setting to take effect.

Accessing the Web UI

This matrix is set to a default static IP Address (192.168.11.143). In order to communicate with it initially the PC must be set to a192.168.11.xxx address with a

subnet of 255.255.0.0. This can be changed back once a static IP is set within a different range.

1. Connect the matrix to the same network as a PC.

2. Open a web browser and enter the IP Address of the matrix.

Default: 192.168.11.143 | Password: admin

Note: The installer password and general password are the same by default. WyreStorm recommends changing the password for installer login to avoid any

unwanted changes being made to the matrix conguration.

Copying EDIDs

1. Set the EDID dipswitch to the Front Panel, Web UI or API EDID Control

(all switches up).

2. Reboot the matrix.

3. Using the front navigation buttons, select the input port for the output.

Example: Input 2 for Output 2

4. Once the output port indicator blinks, press and hold Enter for 5

seconds. OK indicates that the copy was successful, FL-2 indicates that

the copy failed.

5. Reboot the matrix

Note: EDID settings may also be congured using the Web UI. Refer to the

Accessing the Web UI section.

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to all devices in the system and that they

are powered on.

• Verify that all source and HDBaseT connections are not loose and are

functioning properly.

• Verify that the HDBaseT cable is properly terminated per the HDMI/HDBaseT

Wiring section.

• Verify that the matrix, receiving device, and display support the output

resolution of the source. Refer to Video Resolutions in the Specications

table for the max distance based on resolution.

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

No or Intermittent 3rd party Device Control

• Verify that the IR cable(s) is properly terminated.

See IR TX/RX Wiring.

• Verify that the IR emitter is located near the IR receiver on the device.

Troubleshooting Tips:

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

• Use a ashlight to locate the IR receiver behind any tinted panels on the

device being control

SmartEDID/Front Panel/ Web UI 4K UHD 1080p Standard Video

Smart EDID-Display

Lowest Resolution -

2ch only (default)

4K @60Hz 2ch

No HDR 1080p @60Hz 7.1ch 1920x1200 2ch

Front Panel, Web UI or

API EDID Control

4K @30Hz 5.1ch

With HDR 1080p @60Hz 5.1ch 1920x1200 No Audio

4K @30Hz 7.1ch

With HDR 1080p @60Hz 2ch

4K @30Hz 2ch

With HDR

4K @30Hz 8bit 2ch

No HDR

MX-xxxx-H2XC Quickstart Guide | 180622

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

Specyfikacje produktu

Marka:	WyreStorm
Kategoria:	nieskategoryzowany
Model:	TX-H2X-HDBT
Kolor produktu:	Czarny
Technologia łączności:	Przewodowa
Obsługiwane formaty audio:	LPCM, PCM
Diody LED:	Tak
Model:	Nadajnik AV
Maks. rozdzielczość:	4096 x 2160 px
HDCP:	Tak
Szerokość pasma:	9.2 Gbit/s
Aktualizacje oprogramowania urządzenia:	Tak
Maksymalny dystans transferu:	100 m
Obsługiwane rozdzielczości grafiki:	1920 x 1080 (HD 1080),3840 x 2160,4096 x 2160
HDMI in:	1
Zdalne wejście IR:	1
Obsługiwane tryby wideo:	1080p, 2160p
Wyjście audio:	1
Obsługiwane typy kabli:	HDMI, Cat6, Cat6a, Cat7
Wejścia RJ-45:	1
Wyjścia RJ-45:	1
Porty wejściowe RS-232:	1
Interfejs do nagrywania wideo:	1
Port HDBaseT:	Tak
Kierunek sygnału:	Wejście/wyjście
Typ modułu:	Cyfrowy