Instrukcja obsługi Velleman VTHHSC
Velleman
maszyna do lutowania
VTHHSC
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Velleman VTHHSC (25 stron) w kategorii maszyna do lutowania. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/25
VTHHSC
USER MANUAL 2
HANDLEIDING 5
MODE D'EMPLOI 8
MANUAL DEL USUARIO 11
BEDIENUNGSANLEITUNG 14
INSTRUKCJA OBSŁUGI 17
MANUAL DO UTILIZADOR 20
VTHHSC
V. 01 10/11/2017 2 ©Velleman –nv
USER MANUAL
SOLDERING CENTRE
WITH HELPING HAND AND MAGNIFIER
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device
after its lifecycle could harm the environment. Do not dispose of the unit (or
batteries) as unsorted municipal waste; it should be taken to a specialized
company for recycling. This device should be returned to your distributor or to a
local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before
bringing this device into service. If the device was damaged in transit, do not
install or use it and contact your dealer.
2. Safety Instructions
WARNING
Please read the following safety instructions carefully before using this
product.
This device can be used by children aged from 8 years and above, and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning the use
of the device in a safe way and understand the hazards involved. Children shall
not play with the device. Cleaning and user maintenance shall not be made by
children without supervision.
Use a compatible power adapter only.
Connect the power adapter only to a correctly installed mains power socket
whose voltage matches the specifications of the power adapter.
Lay the cable from the power adapter to the device such that no one can trip
over it and/or that the device can be pulled down.
The mains power plug must always be easily accessible, so that in the event of
an emergency the device can be quickly disconnected from the mains power
supply.
The light source in this luminaire is not replaceable. When the light source
reaches its end of life, the whole luminaire shall be replaced.
Do not look directly into the light source thus avoiding potential eye injuries.
Never leave a switched-on device unattended.
VTHHSC
V. 01 10/11/2017 3 ©Velleman –nv
Never leave the device into direct sunlight as sunlight passing through the
magnifying glass could cause fire.
Do not use this device in the immediate surroundings of a bath, a shower or a
swimming pool.
Never operate this device if any part of the device itself or the power adapter is
visibly damaged.
Indoor use only.
3. General Guidelines
Refer to the Velleman ® Service and Quality Warranty on the last pages of this
manual.
All modifications of the device are forbidden for safety reasons. Damage caused
by user modifications to the device is not covered by the warranty.
Only use the device for its intended purpose. Using the device in an unauthorised
way will void the warranty.
Damage caused by disregard of certain guidelines in this manual is not covered
by the warranty and the dealer will not accept responsibility for any ensuing
defects or problems.
Nor Velleman nv nor its dealers can be held responsible for any damage
(extraordinary, incidental or indirect) – of any nature (financial, physical…)
arising from the possession, use or failure of this product.
Keep this manual for future reference.
4. Power Supply
The soldering centre can be powered through a power adapte or with batteries. r
Please use a compatible power adapter (see technical specifications).
To power the soldering centre using batteries:
o Loosen the screw of the spool flanges and turn them towards the
outside. -tighten the spool flanges. Re
o Open the battery cover and remove the battery holder. Insert the
necessary batteries respecting the correct polarity. Insert the holder
back into the device and close the cover.
Specyfikacje produktu
| Marka: | Velleman |
| Kategoria: | maszyna do lutowania |
| Model: | VTHHSC |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Velleman VTHHSC, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje maszyna do lutowania Velleman
10 Września 2024
6 Września 2024
4 Września 2024
4 Września 2024
3 Września 2024
21 Sierpnia 2024
6 Lipca 2024
8 Maja 2024
Instrukcje maszyna do lutowania
- maszyna do lutowania Milwaukee
- maszyna do lutowania Yato
- maszyna do lutowania Parkside
- maszyna do lutowania Toolcraft
- maszyna do lutowania Nedis
- maszyna do lutowania Einhell
- maszyna do lutowania Silverline
- maszyna do lutowania Denon
- maszyna do lutowania Mercury
- maszyna do lutowania Ozito
- maszyna do lutowania RYOBI
- maszyna do lutowania Ersa
- maszyna do lutowania BaseTech
- maszyna do lutowania Güde
- maszyna do lutowania GYS
- maszyna do lutowania Telwin
- maszyna do lutowania Westfalia
- maszyna do lutowania Weller
- maszyna do lutowania Craftsman
- maszyna do lutowania Ridgid
- maszyna do lutowania PowerPlus
- maszyna do lutowania Powerfix
- maszyna do lutowania Monacor
- maszyna do lutowania Steren
- maszyna do lutowania Truper
- maszyna do lutowania Cigweld
- maszyna do lutowania Holzmann
- maszyna do lutowania Epcom
- maszyna do lutowania Uten
- maszyna do lutowania CFH
- maszyna do lutowania Edsyn
- maszyna do lutowania Mag-Torch
- maszyna do lutowania UNIMIG
- maszyna do lutowania Portasol
- maszyna do lutowania JBC
- maszyna do lutowania Hakko
- maszyna do lutowania Fixpoint
- maszyna do lutowania Stamos
Najnowsze instrukcje dla maszyna do lutowania
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024