Instrukcja obsługi Smeg L30FABECR

Smeg kominek L30FABECR

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Smeg L30FABECR (7 stron) w kategorii kominek. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/7

INSTALLATION & USER INSTRUCTIONS

All instructions must be handed to the user for

safekeeping.

MODELS COVERED BY THESE INSTRUCTIONS

L30 FABEBL

L30 FABECR

L30 FABERE

L30 FABESI

WALL MOUNTED ELECTRIC FIRE

Please note: Except where otherwise stated, all rights,

including copyright in the text, images and layout of this

booklet is owned by Smeg (UK) Ltd. You are not permitted

to copy or adapt any of the content without the prior

written permission of Smeg (UK) Ltd.

Revision A - 10/13

L30 FABE

GB IE

SMEG UK LTD

3a Park Square

Milton Park

Abingdon

OX14 4RN

IMPORTANT - THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE

REFERENCE.

When using this electrical appliance, basic precautions should be followed to reduce the risk of fire, electric shock and injury to person,

including the following:

• This heater must be used on an AC supply only and the voltage marked on the heater’s rating label must correspond to the supply

voltage.

• Do not switch the appliance on until it is properly installed as described in this manual.

• The heater must not be located immediately above a socket outlet.

• Keep furniture, curtains and other fabric material away from the appliance.

• Do not leave the appliance unattended during use.

• From time to time, check the cord for damage. Never use the appliance if the cord or any part of the appliance shows signs of damage.

A damaged cord must only be replaced by a qualified person.

• Do not operate this appliance with a damaged plug or cord, after a malfunction or after being dropped or damaged in any way.

• Repairs to electrical appliances should only be performed by a qualified electrician. Improper repairs may place the user at serious risk.

• Do not run the mains cable under carpets, rugs etc.

• Do not cover or obstruct the heater in any way. Overheating will result if it is accidentally covered.

• Never immerse the product in water or any other liquids.

• Do not use this heater where it may come into contact with water e.g. in bathrooms, shower rooms etc.

• Do not use the appliance outdoors.

• Before cleaning the appliance, ensure it is unplugged from the power and that it is completely cool.

• Do not clean the appliance with abrasive chemicals.

• Never use accessories that are not recommended or supplied by the manufacturer. It could cause danger to the user or damage to the

appliance.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Do not lift the appliance by the decorative fascia.

• CAUTION! In order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not be supplied through

an external switching device such as a timer or connected to a circuit that is regularly switched on and off by the utility.

• Do not insert or allow foreign objects to enter the inlet or outlet vents as this may result in electric shock, fire or damage to the

appliance.

• Do not install the fire using an extension cord.

• Unplug from the mains supply if the appliance is not to be used for long periods.

The appliance is supplied with a pre-wired three pin plug (13 Amp fuse rated) and 1.8 metres of electrical cable. It is therefore

necessary for a suitable electrical socket to be located within this distance and be easily accessible. This appliance is designed to

be wall hung, using the wall fixtures/fixings provided. DO NOT recess any part of appliance into the wall. This appliance is

suitable for installation in static holiday/park homes.

Supply Voltage: 220~240V AC, 50Hz 13 AmpFuse Rating:

Heating Elements: Lighting:1800W LED

This fire is fitted with LED’s (Light Emitting Diode) in place of conventional bulbs. LED’s generate the same light levels as

conventional bulbs, but use a fraction of the energy consumed. LED’s are maintenance free and will not require replacing during

the life of the product.

I N S TA L L AT I O N & U S E R I N S T R U C T I O N S

GB IE

3.0 APPLIANCE DATA

Section Contents Page No.

1.0 Important Notes 2

2.0 Installation Requirements 2

3.0 Appliance Data 2

4.0 Unpacking The Appliance 3

5.0 Component Checklist 3

6.0 Site Requirements 3

7.0 Clearances To Combustibles 3

Section Contents Page No.

8.0 Installing The Appliance 4

9.0 Fitting The Decorative Frame 5

10.0 Operating The Appliance 5

11.0 Cleaning And Maintenance 6

12.0 Troubleshooting Guide 7

13.0 Guarantee-Terms And Conditions 7

1.0 IMPORTANT NOTES

2.0 INSTALLATION REQUIREMENTS

Read the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packagingall

and lay on the floor with it’s back surface downward. Note: DO NOT stand the appliance on its frame as this may cause distortion.

Check that the remaining packaging contents correlate with the component checklist below. Please dispose of all packaging at

your local recycling centre.

QUANTITY DESCRIPTION

1 Wall heater

1 Decorative fascia

1 Instruction booklet

1 Remote control

1 Pack of fixing screws and wall plugs (5 x 40mm pozi pan head screws / 5 x wall plugs)

1 Wall mounting bracket

This appliance is designed to be wall mounted using the mounting bracket and fixings provided. The wall should be relatively flat

and not interfere with any of the ventilation slots in the rear panel.

The wall must be structurally sound and of a material capable of withstanding moderate heat. Finished plaster, conventional

wallpaper, dry-lined plaster board are examples of suitable materials. Materials such as flock, blown vinyl, embossed paper and

cloth wall coverings which are sensitive to even small amounts of heat should be avoided, as some discolouration may occur.

It should be noted that the appliance creates warm convected air currents. These currents move heat from the room surroundings

to, and up the wall surfaces adjacent to the heater.

Installing the heater next to these types of wall coverings or operating the heater where impurities in the air, (such as tobacco

smoke) exist, may slightly discolour wall finishing.

If the appliance is to be mounted on a dry lined or timber framed construction then the integrity and ability of the wall to carry

the weight of the appliance must be confirmed. It is important in these circumstances that any vapour barrier and/or structural

members of the house frame are not damaged.

If you are unsure of the ability of the wall to carry the weight and/or which type of wall fixing to use, you should take professional

advice and obtain the correct fixings. Alternatively, find a more suitable wall location.

DO NOT

• mount on a ceiling or floor.

• recess any part of the appliance into the wall, or run the supply cable under carpets.

• site any electrical equipment e.g. plasma screen TV sets etc, on the wall below the appliance.

• site in a position where curtains or drapes could cover the appliance, or other soft materials could cover e.g. below a coat

rack.

• site behind an opening door where mechanical impact/damage could occur.

• site where the supply cable would become a trip hazard.

• sit, stand or forcefully pull on the appliance.

• obstruct, cover or force items into the openings.

• use the heater to dry clothes.

• site/use in an outdoor location(s).

It is important that the following clearances are maintained from the appliance to combustible materials. These clearances are

dependent on the mounting location as defined below:

• The minimum distance from the top of the appliance to a ceiling is 300mm

• The minimum distance from the bottom of the appliance to the floor is 300mm

• The minimum distance to the sides of the appliance is 100mm

• The minimum distance to the front of the appliance is 500mm

4.0 UNPACKING THE APPLIANCE

5.0 COMPONENT CHECKLIST

GB IE

6.0 SITE REQUIREMENTS

7.0 CLEARANCES TO COMBUSTIBLE MATERIALS

Specyfikacje produktu

Marka:	Smeg
Kategoria:	kominek
Model:	L30FABECR
Kolor produktu:	Kremowy
Regulowany termostat:	Tak
Wysokość produktu:	550 mm
Szerokość produktu:	800 mm
Głębokość produktu:	186 mm
W zestawie pilot zdalnego sterowania:	Tak
Rodzaj paliwa:	Prąd elektryczny
Minutnik:	Tak
Moc grzewcza:	1800 W
Konstrukcja produktu:	Kominek
Liczba poziomów zasilania:	7
Typ kominka:	Zamknięty
Orientacja:	Pionowy
Bez odprowadzania:	Nie
Regulowany płomień:	Tak