Instrukcja obsługi Silk'n AS102275A Flash and Go

Silk'n depilator AS102275A Flash and Go

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Silk'n AS102275A Flash and Go (76 stron) w kategorii depilator. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/76

English

Silk’n Flash&Go™ Setup

1. Remove Silk’n Flash&Go™ Hair Removal Unit and other components from box.

2. Verify that the Disposable Lamp Cartridge is inserted properly at the tip of the device.

3. Plug the Adaptor cord into the Silk’n Flash&Go™ Hair Removal Unit socket.

4. Plug the Adaptor into an electrical outlet. The Stand By Indicator Light will turn on.

Your Silk’n Flash&Go™ is now ready to start.

Treating with Silk’n™ Flash&Go for the ﬁrst time

The skin should be shaved, clean, dry and free of any powders, antiperspirants or deodorants.

5. Press the On/Stby Switch. The Power On Indicator Light will turn on and a fan sound (similar to the sound of a hairdryer)

will start.

6. Approximately 3.5 seconds after pressing the On/Stby Switch, the Ready Indicator Light will turn on. The device sets itself

to deliver the lowest energy level pulses. The device is then ready for you to trigger the ﬁrst pulse.

7. If the energy level should be higher than the lowest, press the Energy Level Setting Buttons using the “-“ or “+” to respectively

decrease or increase the energy level, until the desired energy level is set. Energy Level Indicator Lights will coincide with the energy

level setting. (See “Energy Level” frame).

8. Apply the Treatment Surface ﬁrmly to the skin, making sure the skin is spread evenly and smoothly. As soon as the Treatment

Surface is in full contact with the skin, the Ready Indicator Light will start blinking.

9. Press the Pulse Button. The device will ﬁrst determine the color of your skin.

If the color of the skin is light enough for safe application, the device will ﬂash a pulse of light onto your skin, and the Ready Indicator

Light will turn off.

You will see a bright ﬂash of light and simultaneously hear a subtle pop sound, which is a normal noise for the device. You may feel

a mild sensation of warmth and tingling.

Silk’n Flash&Go™ will immediately recharge for the next pulse. After 3.5 seconds the Ready Indicator Light will turn on again.

If you see no light pulse and the Skin Tone Warning Indicator Light blinks your skin tone, measured by the Skin Color Sensor, is

too dark for safe application. Try using the device on a different body part or contact the Silk’n™ support (See: “The Skin Color

Sensor” frame)

10. Remove the Treatment Surface from the treated area of skin.

11. Move the Treatment Surface to another area of skin. Use the pressure marks the device just made on your skin to guide

you for proper positioning of the next pulse, avoiding both gaps and overlaps between pulses (See “Covering skin areas” frame).

Warning: Do not treat the same area of skin more than once per hair removal session! Treating the same area of skin more than

once per session increases the likelihood of adverse effects.

12. Repeat the process starting again with Step 5.

Plan your Silk’n Flash&Go™ hair removal for best results

Typical Silk’n Flash&Go™ hair removal plan during a full hair growth cycle:

The ﬁrst 3-4 hair removal sessions with Silk’n Flash&Go™ will be approximately two weeks apart.

Hair removal sessions 5-7 with Silk’n Flash&Go™ will be approximately four weeks apart.

After that you will typically use Silk’n Flash&Go™ again from time to time if and when needed, until long-term results are achieved.

Typical maintenance with Silk’n Flash&Go™ after achieving long-term hair removal:

Due to hormonal or other physiological changes dormant hair follicles may become active. Maintenance hair removal sessions

with Silk’n Flash&Go™ may be required from time to time.

Quick Start

English

Print date: May 2011

Home Skinovations Ltd. reserves the right to make changes to its products or speciﬁcations to improve performance, reliability, or

manufacturability. Information furnished by Home Skinovations Ltd. Is believed to be accurate and reliable at the time of publication.

However, Home Skinovations Ltd. assumes no responsibility for its use. No license is granted by its implication or otherwise under any patent

or patent rights of Home Skinovations Ltd.

No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose,

without the express written permission of Home Skinovations Ltd.

Data is subject to change without notiﬁcation.

Home Skinovations Ltd. has patents and pending patent applications, trademarks, copyrights, or other intellectual property rights covering

subject matter in this document. The furnishing of this document does not give you any license to these patents, trademarks, copyrights, or

other intellectual property rights except as expressly provided in any written agreement from Home Skinovations Ltd.

Speciﬁcations are subject to change without notice.

Home Skinovations Ltd. Tavor Building, Shaar Yokneam POB 533, Yokneam 20692, ISRAEL www.silkn.com, info@silkn.com

1. What is Silk’n Flash&Go™?...................................................................................................................................................................................... p.3

1.1. Silk’n Flash&Go™ device description............................................................................................................................................................... p.3

1.2. Package contents.............................................................................................................................................................................................................. p.3

1.3. The Disposable Lamp Cartridge..........................................................................................................................................................................p.4

2. Silk’n Flash&Go™ Intended Use............................................................................................................................................................................... p.4

3. Safety with Silk’n Flash&Go™.....................................................................................................................................................................................p.4

4. Contraindications................................................................................................................................................................................................................ p.5

5. When to avoid using Silk’n Flash&Go™................................................................................................................................................................p.6

6. Precautions – How to use Silk’n Flash&Go™ safely.................................................................................................................................. p.7

7. Reducing the risk of injury...................................................................................................................................................................................... p.8

8. Possible Side Effects using Silk’n Flash&Go™................................................................................................................................................... p.9

9. Plan your Flash&Go™ hair removal for best results................................................................................................................................ p.11

10. First steps with Silk’n Flash&Go™.................................................................................................................................................................... p.12

10.1. Silk’n Flash&Go Setup™......................................................................................................................................................................................... p.12

10.2. Treating with Silk’n Flash&Go™ for the ﬁrst time.................................................................................................................................. p.12

10.3. What to Expect when treating with Silk’n Flash&Go? ™.......................................................................................................................p.14

10.4. After treating with Silk’n Flash&Go™................................................................................................................................................................p.14

11. Maintenance of Silk’n™ Flash&Go................................................................................................................................................................... p.15

11.1. Cleaning Silk’n Flash&Go™.................................................................................................................................................................................. p.15

11.2. Replacing the Lamp Cartridge............................................................................................................................................................................ p.15

12. Troubleshooting.............................................................................................................................................................................................................. p.16

12.1. “My Silk’n Flash&Go™ does not start.”........................................................................................................................................................p.16

12.2. “A light pulse is not emitted when I press the Pulse Switch”..............................................................................................................p.16

13. Customer Service....................................................................................................................................................................................................... p.17

14. Speciﬁcations.....................................................................................................................................................................................................................p.17

15. Labeling................................................................................................................................................................................................................................ p.15

EC Declaration of Conformity...................................................................................................................................................................................... p.76

Table of Contents