Instrukcja obsługi SEADA G4K Pro

SEADA Processor G4K Pro

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SEADA G4K Pro (2 stron) w kategorii Processor. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
G4K Pro Quick Start Manual
SD- -016 V04 MA
Note
1. Do not x the device to any surface which is a heat source avoid over heang to
2. Do not cover the surface or venlaon grills of the device avoid over heang to
1. Verify the package contents
Please verify the package contents against the List Below
1. G4K Pro Controller 1
2. Power Adapter 1
3. Ethernet Cable 1
4. Quick Start Guide (SD- -016) 1 MA
5. Audio Cable 1
6. Soware & Documentaon User CD 1
If any of the items in the packing list is missing, please contact your reseller.
2. Set up the G4K Pro
Power up the G4K controller and connect the input and outputs to correct devices.
Figure 1
3. Install the soware on control PC
Install the G4K management soware from the disk Pro
Users will have the soware UI as le.
4. Connect through IP in ‘Device’
The default IP address for G4K Pro controller is
192.168.1.25. Users need to change the IP address of
control PC to the same IP group of G4K Pro.
Change the ‘Obtain an IP address automacally’
to ‘Use the following IP address’ to set up a IP address stac of TCP/IPv4 in Ethernet Properes
IP address: any address between and 192.168.1.2 192.168.1.254 except the address
which has been taken by the G4K Pro
Subnet mask: Default Gateway: 255.255.255.0, 192.168.1.1
Once the control PC IP address having been set up, connect PC to either one of RJ45 ports of G4K
Pro controllers via a network cable and then press the buon to connect the device Connect .
Model: G4KPro-HDMI
1. Lockable Power Supply
2. Reset Buon
Back to Factory Sengs
Press+hold for 3 seconds
3. RJ45 Ethernet Ports
4. HDMI Input Port
5. Status Lights
6. Audio Output Port
7. HDMI Output Ports
8. Daisy Chain HDMI Ports
To Other G4K Pro Units
9. Screw holes for Lockable
HDMI cables
Please take the cover screws
out before use
A
Figure 1
1 2 3 4 5
6 7 8
9
Figure 2
G4K Pro Quick Start Manual
SD- -016 V04 MA
5. Set up video wall layout in ‘Output’
Once the unit is connected, press to set up the layout. ‘Output’
Type in the Dotpitch and bezel sizes (check display datasheet) in . ‘output’
Dot Pitch: Display area Length (L) ÷ Quanty of Horizontal pixel (e.g.
1920)
For example
46’’ screen has 0.531mm Dot Pitch
49’’ screen has 0.561mm Dot Pitch
55’’ screen has 0.631mm Dot Pitch
And then press to apply the changes to all screens ‘Apply ’ To All Monitors
Press apply the changes only to the current ‘Apply To Single Monitor’ to
highlighted screen
Move/rotate the screens in soware to create the desired layout
Enter any degree in and then press ‘Angle’ ‘Rotate All Monitors’ (A)
Enter any degree in and then press for single screen ‘Angle’ ‘Rotate’ (B)
Press to enable any layout change ‘Apply’
Note: no change will be applied to the video wall unl buon has been pressed Apply’ (C)
6. Set up input video window in ‘I put’
n
n
n
nn
Once the video wall layout having been set up,
press to set up the input video window ‘Input’
Users are able to move/resize the input video
window onto the video wall
Users are able to open/close the input video
window via pressing the buon of and ‘Open Window’
‘Close Window’ respecvely.
Users are able to open mul video input windows
when mul G4Ks are connected
Highlight the G4K device whose input window
needed to be opened
And then press the buon to ‘Open Window’
open the window
Each input window will have a unique window ID
There are 3 modes for opening input source window
Lock Aspect Rao Window covers the screen with the same aspect rao as input source
Frame Window covers the video wall to the edge of frames of the screens
None Window covers the video wall to the display edge of the screens
7. Create Pre-set layout for G4K Pro
There are two ways to create and save pre-set layouts for future recall.
One way is to save up to 4 layouts onto the device so that the layouts can be loaded by G4KPro
management soware, iGPro from Apple App Store or 3rd party controller via telnet (Figure 4- .A)
Another method is to use Save & Load buons on toolbar save unlimited layouts onto to
control PC and load them using G4KPro management soware. There are a few sample layouts already
in the folder for users to use.
This quick start guide provides basic instrucons for seng up SEADA G4K Pro video wall controllers. For
addional informaon (e.g. daisy chain) about how to use the controllers, please refer to the G4K Pro User
Guide (SD- -017)MA , which is available on the CD included in this package.
Figure 3
Figure 4
Figure 4
A
A
B
C

Specyfikacje produktu

Marka: SEADA
Kategoria: Processor
Model: G4K Pro

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SEADA G4K Pro, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą