Instrukcja obsługi Saturn ST-CH7408

Saturn Okap wyciągowy ST-CH7408

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Saturn ST-CH7408 (22 stron) w kategorii Okap wyciągowy. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/22

ST-CH7408

KITCHEN HOOD

КУХОННАЯ ВЫТЯЖКА

КУХОННА ВИТЯЖКА

KITCHEN HOOD

Dear Buyer!

We congratulate you on having

bought the device under trade

name “Saturn”. We are sure that

our devices will become faithful

and reliable assistance in your

housekeeping.

Avoid extreme temperature

changes. Rapid temperature

change (e.g. when the unit is

moved from freezing temperature

to a warm room) may cause

condensation inside the unit and a

malfunction when it is switched

on. In this case leave the unit at

room temperature for at least 1.5

hours before switching it on.

If the unit has been in transit,

leave it indoors for at least 1.5

hours before starting operation.

Thank you for the use of this type of

decorative ventilator of the company.

The western-style ventilator is

luxuriously, artistic, and of great

suction. It suits high-grade cabinets.

Before the use please read the

instruction.

Contents

I Structure description ...... 3

II Matters need attention for

installation .................... 4

III Method of installation ..... 5

IV Use method .................. 7

V Directions for use ........... 8

VI Maintenance .................. 8

VII Malfunctions and treat

ments .............................. 9

VIII Electric principle scheme… 9

I. Structure description

II. Matters need attention for

installation

1. Install surroundings (shown in

figure 1)

Excessive windows and doors should

be avoided around it when the Kitchen

hood is Installed, because when there

are too many windows and doors, the

air convection is oversized, which

enable the lampblack rise to the

250mm effective attraction scope. The

efficiency of the kitchen hood comes

under the influence. 2. Ideal location for the

installation (shown in figure 2)

The kitchen hood is installed over the

cooker hood, the range between the

predestined affinity low end and the

stove surface should be at least 650

mm. Us scope is better to be in 650-

700mm.

3. Requests for the installation of

smoke pipe (shown in figure 3)

(1) The distance from the exit of the

smoke pipe to the organism should

not be too long. Make the radius of

turn as large as possible. Make few

curves, or the effect will not be so

good.

(2) The exhaust duct should reach

outdoor of the common smoke pipe,

and the connector must be narrow.

Please don't discharge the waste gas

into hot flue.

4. Keeping the organism level

(shown in figure 4)

After the installment, watch out if it's

horizontal to avoid the spillover of the

oil, caused by the oil cup being

oblique.

1. The waste gas should not be

discharged into the hot flue, which is

used to discharged the smoke of

burning gas or other kinds of fuel.

2. When boring holes, avoid the power

cords inside the wall, so as not to get

an electric shock (shown in figure5).

3. The electric outlet must be earth

lead and the plug can't be changed

optionally (shown in figure 6).

4. Proper space (usually about 10mm)

should be left on both sides of the

organism when making the cabinet.

The boards that cover the organism

should be turnable, so as to be

convenient for maintenance and repair

(shown in figure 7).

III. Method of installation

1. Determining the location: install the

kitchen hood horizontally above the

stove. The bottom of the range hood

is about 650mm to 750mm high. The

size the with drawable boards we refer

to you is 430mm, which can be

adjusted according to actual situation.

The open holes must be vertical,

centered and horizontal to the

organism.

2. Installing the cladding: first bore

three holes in the dry wall, whose

diameters are 8mm and depths are

50mm to 60mm. Then put the

expansion tube into the holes. At last

use the lag wood screws of the size of

ST4х50 in the packing box to set the

cladding.

3. Adjusting the stretched tube (if

there is): pull out the stretched tube,

remove the protective layer, put it into

the gap between the decorated tube

and organism and adjust to the

appropriate height.

4. Installing the organism (in figure

8): press and slide the pothook on the

cladding into the holes at the back of

the organism. Rock the organism with

the hand to see, if it is fastened.

5. Fixing the exhaust duct: insert the

exhaust duct between the inside track

and the outside track of the air outlet,

set with ST3X6 bolt, and put the other

end outdoor.

6. Fixing the exhaust duct: insert the

exhaust duct into the inside track of

the check valve's air outlet, set with

ST3X6 tapping screw and connect the

other end outdoor (the air outlet is at

the top of the organism).

7. Fixing the other end of the exhaust

duct (reference)

(1) When the exhaust duct and the

charging floor are just against the

window: remove a pane of glass and

fix a veneer with a hole. You can also

make a hole on the glass.

(2) When the charging floor is not

near the window:

Choose the nearest charging floor and

the window, which can reach outdoor

to fix the exhaust duct by going

through the window; or choose the

nearest charging floor and bore a hole

in the wall, then make the exhaust

duct go through the wall.

(3) Bore a hole in the wall:

Measure and draw a circle on the wall

(the diameter is a little bigger, than

that of the exhaust duct), and bore a

hole with long drill, pay attention to

the structure and metal of the wall.

Don't destroy the wall surface beyond

the hole. The diameter of the hole

should be close to the diameter of the

exhaust duct, or the smoke can not go

out smoothly. The noise will be too

much and the wind rate will also

reduce.

Specyfikacje produktu

Marka:	Saturn
Kategoria:	Okap wyciągowy
Model:	ST-CH7408

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Saturn ST-CH7408, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Okap wyciągowy Saturn

Saturn ST-CH7409 Instrukcja

2 Października 2024

Saturn ST-CH7402 Instrukcja

13 Września 2024

Saturn ST-CH7408 Instrukcja

4 Września 2024

Instrukcje Okap wyciągowy

Najnowsze instrukcje dla Okap wyciągowy

Pelgrim ISW990 Instrukcja

15 Października 2024

PKM 6080X Instrukcja

15 Października 2024

M-System MSPK 761 IX Instrukcja

15 Października 2024

Pelgrim ISWA991RVS Instrukcja

15 Października 2024

Pelgrim ISW751RVS Instrukcja

15 Października 2024

Pelgrim ISW771RVS Instrukcja

15 Października 2024

Amana WVW53UC6HV Instrukcja

15 Października 2024

Haier HPH60IMB2 Instrukcja

15 Października 2024

Haier HC60BMB2 Instrukcja

15 Października 2024

Haier HPH90IMB2 Instrukcja

15 Października 2024