Instrukcja obsługi Renkforce RF100 v2

Renkforce drukarka 3D RF100 v2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Renkforce RF100 v2 (48 stron) w kategorii drukarka 3D. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/48

Gebruiksaanwijzing

RF100 v2 3D-printer (compleet gemonteerd)

Bestelnr. 1548286

Inhoudsopgave

Pagina

1. Inleiding ...............................................................................................................................................................4

2. Verklaring van pictogrammen ..............................................................................................................................4

3. Bedoeld gebruik ...................................................................................................................................................5

4. Leveringsomvang ................................................................................................................................................5

5. Inhoud SD-kaart ...................................................................................................................................................6

a) 3D Models (3D-modellen) ..............................................................................................................................6

b) Cong ............................................................................................................................................................6

c) Manual (handleiding) ..................................................................................................................................... 7

d) Software ........................................................................................................................................................7

6. Kenmerken en functies ........................................................................................................................................ 7

7. Werkingsprincipe van de 3D-printer ....................................................................................................................8

8. Veiligheidsinstructies ...........................................................................................................................................9

a) Algemeen ......................................................................................................................................................9

b) Aansluiten op het stroomnet ........................................................................................................................ 11

9. Bedieningselementen en onderdelen ................................................................................................................12

a) Printer (voorkant en achterkant) .................................................................................................................. 12

b) Accessoires .................................................................................................................................................12

10. Voor de installatie ..............................................................................................................................................13

11. Installatie ............................................................................................................................................................13

a) Plaatsing van de 3D-printer ......................................................................................................................... 13

b) Installatie en aansluiting ..............................................................................................................................13

12. Bedieningspaneel ..............................................................................................................................................15

a) Basisfuncties ...............................................................................................................................................15

b) Menu-opties en functies ..............................................................................................................................15

c) < Info screen > .............................................................................................................................................18

13. Algemene opmerkingen over 3D-printen ........................................................................................................... 19

a) Temperatuur van de nozzle .........................................................................................................................19

b) Voorkom verstopping van de nozzle ............................................................................................................19

c) Laagdikte ..................................................................................................................................................... 20

14. Voorbereiding .....................................................................................................................................................21

a) Printbed kalibreren ......................................................................................................................................21

b) Filament installeren .....................................................................................................................................22

c) Filament laden ............................................................................................................................................. 23

d) Filament veranderen / vervangen ................................................................................................................24

e) Cura-software installeren (optioneel) ...........................................................................................................24

15. Printen vanaf de SD-kaart .................................................................................................................................25

a) Begin met printen ........................................................................................................................................25

b) Pauzeer het printen .....................................................................................................................................26

c) Tijdens het printen de parameters aanpassen ............................................................................................26

d) Stop met printen ..........................................................................................................................................26

e) < Emergency stop > (noodstop) uitvoeren ..................................................................................................26

f) De 3D-printer opnieuw opstarten .................................................................................................................27

16. Printen via de Cura-software .............................................................................................................................27

a) Algemene opmerkingen ...............................................................................................................................27

b) Installatie .....................................................................................................................................................28

c) Instellen van de software - Windows® .........................................................................................................28

d) Instellen van de software - Mac OS .............................................................................................................32

e) Software-instellingen - Windows® ................................................................................................................ 35

f) Conguratiebestandladen-Windows® .......................................................................................................38

g) Conguratiebestandladen-MacOS ..........................................................................................................38

h) Modellen laden – Windows® en Mac OS ..................................................................................................... 39

i) Beginnen met printen ..................................................................................................................................40

j) Stoppen met printen ....................................................................................................................................41

k) < Emergency Stop > (noodstop) uitvoeren ................................................................................................. 41

17. Reiniging en onderhoud .....................................................................................................................................41

a) Het apparaat reinigen .................................................................................................................................. 41

b) De nozzle reinigen .......................................................................................................................................41

c) De binnenkant van de extruder reinigen ......................................................................................................42

d) Het printbed reinigen ...................................................................................................................................42

e) De zekering vervangen ................................................................................................................................42

f) Filament ontladen ........................................................................................................................................ 43

g) Bewaren van de 3D-printer ..........................................................................................................................43

18. Probleemoplossing ............................................................................................................................................44

19. Verwijdering .......................................................................................................................................................47

20. Technische gegevens ........................................................................................................................................47