Instrukcja obsługi PAC RadioPRO 4 RP4.2-HY12

PAC radio RadioPRO 4 RP4.2-HY12

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC RadioPRO 4 RP4.2-HY12 (7 stron) w kategorii radio. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/7
Pacic Accessory Corporation
® | Ph. 866-931-8021 | support@pac-audio.com
©2015 Pacic Accessory Corporation
www.pac-audio.com
P ifi A C ti
RP4.2-HY12
Radio Replacement &
Steering Wheel Control Interface
for Hyundai Veloster
Rev. 101515
Page 1
Introduction & Features
Important Notes
The RP4.2-HY12 interface allows the replacement of a factory radio in the Hyundai Veloster. Using this interface will
retain factory features such as: steering wheel controls (SWC), secondary screens, reverse camera and factory SPDIF
audio amplier (seperate part required, part # RPA-SPDIF) whenever the original radio is removed. Use of this interface
also allows you to program two radio functions to each SWC button by using short press long press dual command
functionality. The RP4.2-HY12 also provides data bus driven outputs such as vehicle speed sense (VSS), illumination,
reverse trigger and parking brake.
1. Does not retain Blue Link. You must use the RP5.2-HY12 to retain Blue Link.
2. The AUX connection in the RP4 harness will only provide sound if the aftermarket radio has a USB port. This is because the
USB port provides the power to make the factory USB/AUX port work. If you have connected the USB plug to your aftermarket
radio and it is still inoperable, this means that the aftermarket radio’s USB port is not supplying enough current.
3. When using the RPA-SPDIF in factory amplied vehicles, you can adjust factory amplier settings such as Bass, Mid, Treble,
Fader, Balance and Gain with the RadioPRO app found at www.pac-audio.com. Please refer to page 6 for detailed instructions
on the app and the functionality of this wire.
4. In vehicles equipped with auto climate controls, you will lose the fan mode, fan speed, auto status and temperature display.
Wiring Connection Chart
3.5mm Jack SWC Output
Pink MS-CAN + Input
Pink/Black MS-CAN - Input
Blue/Yellow SWC Output
Red/White 12v+ Programmable
Output (1 amp)
Orange/White Illumination Output
Pink Vehicle Speed
Sense Output
Violet/White Reverse Output
White/Black HS-CAN + Input
White/Red HS-CAN - Input
White Analog SWC
Orange/Black Illumination Input
Light Green Parking Brake
Output (-)
Blue/White Amp Turn On Input
Interface Connector 2
Yellow Battery +12v
Black Ground
Blue Power Antenna
Turn On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Yellow RCA Factory Reverse
Camera Video (if
equipped)
Vehicle ConnectorInterface Connector 1
Red Accessory Output
(10 amp)
Yellow 12v+
Black Ground
Red Accessory Output
Pacic Accessory Corporation
® | Ph. 866-931-8021 | support@pac-audio.com
©2015 Pacic Accessory Corporation
www.pac-audio.com
P ifi A C ti
RP4.2-HY12
Radio Replacement &
Steering Wheel Control Interface
for Hyundai Veloster
Rev. 101515
Page 2
Default Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require
programming unless you wish to re-assign the SWC functions, utilize short press long press dual command functionality or assign
the programmable 12v output to a SWC button. The SWC can always be restored to default settings by pressing and releasing
the program button on the side of the interface once and waiting 7 seconds for the LED to ash 3 times.
Installation Steps
1. The radio select dipswitches on the side of the interface must be adjusted to the proper radio
setting before plugging the interface into the vehicle.
2. Make all connections as described in the connection chart on page 1. Vehicles without a factory amplier: Connect the
aftermarket radio’s front and rear speaker wires to the vehicle connector. Vehicles with a factory amplier: Connect the
aftermarket radio’s front speaker wires to the SPDIF converter (sold seperately, part # RPA-SPDIF), then connect the SPDIF
converter to the 6-pin connector located on the RP4.2 harness.
3. Connect the SWC wire to the aftermarket radio (aftermarket radio must support a wired remote input).
4. Once all connections have been made, plug the interface into the vehicle.
5. If you wish to reassign functions to the SWC, utilize short press long press dual command functionality or assign the
programmable 12v output to a SWC button, follow the optional programming instructions on the next page.
Module Layout
Module Status LED
Programmable
Output/USB Status
LED
Interface Connector 1
Expansion
Port
Interface Connector 2
Programming
Button
USB Port
Radio Select Dipswitches
Steering Wheel Controls
DIP
1234
ON
Alpine JVC Kenwood Clarion Pioneer/Other Sony Fusion
1 2 1 & 2 3 1, 2, & 3 4 1 & 4
SET RADIO DIPSWITCHES TO THE ON POSITION
Pacic Accessory Corporation
® | Ph. 866-931-8021 | support@pac-audio.com
©2015 Pacic Accessory Corporation
www.pac-audio.com
P ifi A C ti
RP4.2-HY12
Radio Replacement &
Steering Wheel Control Interface
for Hyundai Veloster
Rev. 101515
Page 3
Optional Steering Wheel Control Programming
If you wish to re-assign the SWC functions, utilize short press long press dual command functionality or assign the programmable
12v output to a SWC button, the interface must be programmed in the specic order shown in the chart on page 4. If you come
across a function in the chart that your steering wheel does not have, or you do not want to program, press and release the
programming button on the side of the interface to skip that function. The LED will ash off and on conrming that you have
successfully skipped that function and are ready to proceed to the next one.
Short Press Long Press Dual Command Functionality
This feature allows you to assign two aftermarket radio functions to each of the vehicles SWC buttons. It can be used with as
many of the buttons as the user likes or none at all. When this functionality is implemented, quickly pressing and releasing a SWC
button will initiate the short press command while pressing and holding a SWC button for longer than two seconds will initiate the
long press command. Please note that no long press commands are programmed by default. If you wish to assign dual command
functionality to the SWC please follow the programming steps on the next page.
Programmable 12v Output
The red/white wire on the interface can be programmed via the RadioPRO app to do a pulsed or latched 12v output which can
then be assigned to any of the vehicle’s factory SWC buttons. When assigned, the factory SWC button will activate the pulsed or
latched output to control external accessories. Please refer to page 6 for more details on how to use the app to set this feature.
Default SWC Button Assignments
Alpine JVC Kenwood Clarion Pioneer Sony Fusion
V
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Track + Track +
Track - Track - Track - Track - Search - Track - Track - Track -
V
oice VR Voice Voice Mute Voice Mute Mute
Mute Mute Mute
A
tt N/P Mute Band N/P
Phone Answe
r
Receive Receive
nswe
Send Mute
A
nswer/End
A
udio
Phone End
E
n
d
R
e
j
ect
V
o
i
ce
E
n
d
E
n
d
R
e
j
ect
/S
ource
P
owe
r
Steering Wheel Controls (cont.)
DIP
1234
ON
Alpine JVC Kenwood Clarion Pioneer/Other Sony Fusion
1 2 1 & 2 3 1, 2, & 3 4 1 & 4
SET RADIO DIPSWITCHES TO THE ON POSITION


Specyfikacje produktu

Marka: PAC
Kategoria: radio
Model: RadioPRO 4 RP4.2-HY12

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PAC RadioPRO 4 RP4.2-HY12, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje radio PAC

Instrukcje radio

Najnowsze instrukcje dla radio

Ruarkaudio

Ruarkaudio Rseven Instrukcja

15 Października 2024
Ruarkaudio

Ruarkaudio MR1 Instrukcja

15 Października 2024
Denver

Denver TWE-55B Instrukcja

15 Października 2024
Audiosonic

Audiosonic CL-1486 Instrukcja

14 Października 2024
Sangean

Sangean DPR-39 Instrukcja

13 Października 2024
Roberts

Roberts Stream 93i Instrukcja

13 Października 2024
Sangean

Sangean RCR-9 Instrukcja

13 Października 2024
Uniden

Uniden UH45CP Instrukcja

12 Października 2024
Muse

Muse M-178 P Instrukcja

10 Października 2024
Sencor

Sencor SIR 5000WDB Instrukcja

10 Października 2024