Instrukcja obsługi Ozito BDP-450

Ozito Wiertarka BDP-450

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito BDP-450 (8 stron) w kategorii Wiertarka. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/8
PEDESTAL
DRILL PRESS
450W
INSTRUCTION MANUAL
SPECIFICATIONS
Mains Voltage: 230–240V ~ 50Hz
Power: 300W (S1);
450W (S6 20%)
No Load Speed: 600 - 2,650/min
Chuck: Ø13mm Keyed
B16 Morse Taper
Chuck Size: Ø1.5 - 13mm
Max. Drilling Depth: 50mm
Table Tilt: 0-450 (Left & Right)
Weight: 13kg
BDP-450
STANDARD EQUIPMENT
3 YEAR REPLACEMENT WARRANTY*
Your product is guaranteed for a period of If 36 months from the original date of purchase.
a product is defective it will be replaced in accordance with the terms of this warranty. Warranty
excludes consumable parts, for example: valve adapters and accessories.
*This product is intended for DIY use only and replacement warranty covers domestic use.
WARNING
The following actions will result in the warranty being void.
If the tool has been operated on a supply voltage other than that specified on the tool.
If the tool shows signs of damage or defects caused by or resulting from abuse, accidents
or alterations.
Failure to perform maintenance as set out within the instruction manual.
If the tool is disassembled or tampered with in any way.
Professional, industrial or high frequency use.
WARRANTY
Ozito Industries Pty. Ltd. 25 Fox Drive, Dandenong South, Victoria, Australia 3175.
ozito.com.au
Head Assembly, Table, Baseplate &
Main Column
Chuck Guard, Guard Arm, 3 x Feed
Wheel Handles & Belt Tension
Handle
Chuck, Chuck Key, 3 x Column Bolts
& 2 x Hex Keys
0622
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY
YOU MUST RETURN THE PRODUCT TO YOUR NEAREST
BUNNINGS WAREHOUSE WITH YOUR BUNNINGS
REGISTER RECEIPT. PRIOR TO RETURNING YOUR
PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
Australia: 1800 069 486
New Zealand: 0508 069 486
The benefits provided under this warranty are in addition to other rights and remedies which
are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty,
however, where you have suffered any additional direct loss as a result of a defective product
you may be able to claim such expenses by contacting our customer service helpline above.
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE
THE MODEL NUMBER AND DATE OF PURCHASE
AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE
WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS
YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
Assembling The Drill Press
1. Carefully remove the contents from the packaging.
2. Select a firm, level surface on which to assemble the drill press.
3. Align the holes on the base
of the main column with the
holes in the baseplate.
4. Place a washer onto each of
the 3 column bolts and use
these to fasten the column
into place; use an M10
wrench to tighten securely.
5. Rotate the table lever anti-clockwise
to loosen the collar.
6. Slide the table collar onto
the column and secure
at the desired position by
tightening the collar bolt.
7. Place the motor unit on the
main column and use a 4mm
hex key to tighten the grub
screw on the side of the
motor unit.
8. Screw the 3 feed wheel
handles into the slots on the
feed wheel hub.
9. Screw the belt tension handle into
the slot on the belt tension hub.
1. Belt Tension Lever
2. On/Off Switch
3. Guard Arm Lock
4. Guard Arm
5. Pulley Cover
6. Motor
7. Main Column
8. Table Lever
9. Baseplate
10. Table Tilt Bolt
11. Table
12. Chuck Guard
13. Guard Locking Screw
14. Keyed Chuck
15. Depth Indicator Lock
16. Motor Locking Screw
17. Chuck Key Holder
18. Feed Wheel Handle
19. Pulley Cover Lock
PEDESTAL DRILL PRESS
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
2
3
4
7
8
6
5
19
1
18
17
16
14
15
13
12
11
10
9
WARNING! ENSURE THE TOOL IS TURNED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING OPERATIONS.
ONLINE MANUAL
Scan this QR Code with your mobile
device to take you to the online manual.
Installing The Chuck & Chuck Guard
1. With the chuck jaws fully
retracted into the chuck,
align the chuck with the
spindle and place it the drill
table.
2. Raise the table until the
chuck is approximately
25mm from the spindle.
Note: Use a piece of timber to protect the chuck and avoid
scratches.
3. Use the feed wheel handles
to slowly lower the spindle
until the chuck is pushed
securely onto the spindle.
Note: A gentle tap on the
timber is required to secure the
keyed chuck onto the tapered
drive shaft
4. Remove the 2 screws on the side of the guard
arm with a screwdriver (not supplied) and slide
it into the arm holder on the motor unit.
Note: Ensure the 2 screws and guard arm lock
knob will face the user when reassembled.
5. Tighten the stop screw.
6. Align the holes on the chuck
guard with the holes on the
guard arm and refit the 2
removed screws to hold the
guard in place.
7. Use the guard locking screw to
lock the guard arm in the desired
position.
Attaching A Drill Bit
1. Swing the chuck guard out
of the way.
2. Push the chuck key into
any of the holes in the side
of the chuck and turn it
anti-clockwise to loosen the
chuck jaws.
3. Insert the drill bit fully into
the chuck.
4. Hold the drill bit in one hand
and rotate the chuck key
clockwise to tighten the jaws
around the drill bit.
Note: Ensure drill bit is straight
before fully tightening.
Note: Tighten the chuck jaws
from all 3 holes with the chuck key fasten the drill bit securely.
5. Swing the chuck guard back
into place and store the
chuck key in the holder on
the side of the motor unit.
25mm
a.
b.


Specyfikacje produktu

Marka: Ozito
Kategoria: Wiertarka
Model: BDP-450

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ozito BDP-450, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Wiertarka Ozito

Ozito

Ozito BDP-500 Instrukcja

15 Października 2024
Ozito

Ozito PXDDS-200 Instrukcja

30 Września 2024
Ozito

Ozito BDP-450 Instrukcja

24 Września 2024
Ozito

Ozito HDR-1050U Instrukcja

20 Września 2024
Ozito

Ozito HDR-3000U Instrukcja

16 Września 2024
Ozito

Ozito HDR-1100U Instrukcja

15 Września 2024
Ozito

Ozito PXBHS-100U Instrukcja

15 Września 2024
Ozito

Ozito PXHDS-301U Instrukcja

15 Września 2024
Ozito

Ozito DP-350U Instrukcja

13 Września 2024
Ozito

Ozito CDL-1810U Instrukcja

7 Września 2024

Instrukcje Wiertarka

Najnowsze instrukcje dla Wiertarka

Einhell

Einhell BM-G1100 E Instrukcja

14 Października 2024
Sun Joe

Sun Joe 24V-DDK-LTX-PNK Instrukcja

14 Października 2024
DeWalt

DeWalt DWD450 Instrukcja

14 Października 2024
Black & Decker

Black & Decker GC1800 Instrukcja

13 Października 2024
Rupes

Rupes BH 252R Instrukcja

13 Października 2024
Makita

Makita HP2070 Instrukcja

13 Października 2024
Makita

Makita DHR263ZJ Instrukcja

12 Października 2024
Black & Decker

Black & Decker BDCDE120 Instrukcja

10 Października 2024
Gamma

Gamma BH-1500W Instrukcja

9 Października 2024
Flex

Flex IW 1/2" 1500 18-EC Instrukcja

9 Października 2024