Instrukcja obsługi Optoma BX-AL133

Optoma Akcesoria do projektora BX-AL133

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Optoma BX-AL133 (19 stron) w kategorii Akcesoria do projektora. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/19
User’s Manual
BX-AL133 Anamorphic Lens
User’s Manual
BX-AL133
For more information, please visit our website at:
http://www.OptomaUSA.com User’s Manual | 2
Safety
1. Read and understand instructions and heed warnings before beginning installation.
2. Mount rail securely. The lens is heavy, and requires a secure and stable surface.
Fasteners in sheetrock alone are not safe. Reciprocal lens motion can and will work
them loose. Use a board, plate, or projector mount fixed to ceiling joists or studs.
3. Anticipate unexpected lens motion. A malfunction can cause the lens to move
unexpectedly. Disconnect the power when installing, working on or repositioning
the lens. While on a ladder, do not stand in the direct path of the lens in case of
unexpected or accidental movement.
4. Do not install the lens in a wet or moist environment, or where the mechanism will be
exposed to extreme or external weather conditions. The lens is for indoor use only.
5. Never pour any liquid or push any object into the enclosure.
6. Do not install in direct path of heater vents or projector exhaust ports. Do not block
any of the vents or holes in the enclosure.
7. The power adaptor is intended for 100- 220 volt, 50-60 cycle AC power only.
8. Do not subject power cord to conditions which will wear through or cut the insulation.
Avoid excessive tension or chafing of the cord.
9. Do not service the motor drive or electronics. There are no user serviceable parts.
Contact your dealer or send to a factory approved facility. Opening the case will void
the warranty.
10. Exercise extreme caution when working on a ladder. Do not work directly above
another person, particularly a child. Plan all work carefully. Accidentally dropping a
drill, hammer, or the lens assembly can cause serious bodily injury.
11. Pushing or forcing the sled by hand may damage the circuit board. Should it be
necessary to move the sled by hand, make sure it is done slowly and lightly.
12. The Optoma motorized sled will ramp up and down at the beginning and end of the
traversal to minimize swaying forces at the mount. As the motor accelerates and
brakes, there is a minimal change in the sound.
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
September 2005 Edition
User’s Manual
BX-AL133
For more information, please visit our website at:
http://www.OptomaUSA.com User’s Manual | 3
Introduction
Thank you for purchasing the Optoma BX-AL133 anamorphic lens. The lens and
motorized sled is outfitted with a custom mechanism designed exclusively for use in a
home theater environment.
No oil or liquid based lubricants are used to assure the maximum cleanliness of optical
components. Both lens and drive will provide years of maintenance free service. The
Optoma system is built and tested in the USA with the strictest quality standards and
certifications.
Features and benefits:
Easy, straight forward installation and operation
Machined, high-grade, anodized aluminum components
Repeatable precision positioning system
Flexible mounting options for either table top or ceiling mount
Speed selector for high or low speed operation
Configurable “lens in” position
Extra external IR sensor for remote mounting (if needed)
Input 12V jack for automatic lens trigger
Output 12V jack for screen masking trigger
Non-mechanical long life optical stop sensors
Dry operating precision linear bearings
Heavy-duty, high-precision NEMA 23 stepper motor
Custom built, low noise stepper drive circuitry and firmware
Endurance tested to more than 250,000 traversals
8-button long-range (up to 50 feet) remote control with discrete functions
Backlit logo with on/off lighting control
Reversible logo plates
Built and tested in the USA
FCC, CE and UL certified

Specyfikacje produktu

Marka: Optoma
Kategoria: Akcesoria do projektora
Model: BX-AL133

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Optoma BX-AL133, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Akcesoria do projektora Optoma

Optoma

Optoma OWM3000 Instrukcja

15 Września 2024
Optoma

Optoma OCMPROS Instrukcja

28 Sierpnia 2024
Optoma

Optoma BX-AL133 Instrukcja

19 Sierpnia 2024
Optoma

Optoma OCM818B-RU Instrukcja

19 Sierpnia 2024
Optoma

Optoma LR4DM Instrukcja

19 Sierpnia 2024
Optoma

Optoma 3D-RF Glasses Instrukcja

18 Sierpnia 2024
Optoma

Optoma EVBMN-M110 Instrukcja

17 Sierpnia 2024

Instrukcje Akcesoria do projektora

Najnowsze instrukcje dla Akcesoria do projektora

Barco

Barco R9853370 Instrukcja

14 Stycznia 2025
Vogel's

Vogel's PPA 904 Instrukcja

10 Stycznia 2025
Roadinger

Roadinger MBT-3 Instrukcja

7 Stycznia 2025
Chief

Chief RPMC198 Instrukcja

31 Grudnia 2025
Chief

Chief RPMA360 Instrukcja

31 Grudnia 2025
Chief

Chief RSMA342 Instrukcja

31 Grudnia 2025
Chief

Chief RSMA360 Instrukcja

31 Grudnia 2025
Chief

Chief RPMC266 Instrukcja

31 Grudnia 2025
Chief

Chief RSMC360 Instrukcja

31 Grudnia 2025
Chief

Chief RPMA303 Instrukcja

31 Grudnia 2025