Instrukcja obsługi Optex SIP-3020

Optex Niesklasyfikowane SIP-3020

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Optex SIP-3020 (12 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

- 1 -

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL

2.3-4.0 m

(7.6-13 ft.)

INSTALLATION AND MAINTENANCE NOTES

Warning Caution

Never repair or

modify product

Hold the main unit

securely when you

install or service it.

If you remove your

hands from the main

unit when cables are

connected to it, the

main unit may fall

and the connector

cables may break

or the circuit board

may be damaged.

Caution

Verify that the

power is off before

connecting the

wiring.

PARTS IDENTIFICATION

No.59-1564-2 0911-01

INSTALLATION INSTRUCTIONS

Synthesized Intelligent PIR

REDWALL-V series

Synthesized Intelligent PIR

REDWALL-V series

FEATURES

* Intelligent PIR Detection System

- Detection of ambient temperature and illuminance for

automatic sensitivity management

- Advanced detection algorithm

- Three dual pyro-elements with patented Double Conductive

Shielding for main area

* Built-in creep zone detector (Double dual pyro-elements)

* Anti-vandalism functions

- Anti-rotation function with 3-axis accelerometer

- Anti-masking function with photo-beam

- Reinforced polycarbonate housing

- Max. 4m (13ft.) installation height

* Independent sensitivity selector for creep/near/far areas

* Detection logic selector

* Detection range selector

* Independent N.C. and N.O. outputs

* Adjustable alarm interval time

REDWALL-V

: Synthesized Intelligent PIR with creep zone

SIP-3020/5

SIP-4010/5

SIP-404/5

•

Mount the detector so that the majority of trafﬁ

ﬂ ow is across the detection pattern.

*1: Not used for the SIP-4010/5 and SIP-404/5.

2-1

INSTALLATION HINTS

Base

Fixing screw

for the base

Main unit

Masking plate for near

area (*1)

Window

Fixing screw

for the cover

Cover

Far area mirror

Masking plate for far area

Fixing rubber form

Adjustment screws

(two facing each other)

Angle adjustment guide

Near area mirror

Arrow marking

Fixing screw

Nylon wire

loop

When servicing, the sensor

can be hooked onto the

base using the nylon wire

loop.

Creep unit Fixing rubber

form (*1)

- 2 -

3-1

Wall Mounting

Attach the paper template (an accessory) onto the wall,

and drill a 6-mm dia. mounting hole and a cabling hole.

Insert the anchor bolt (an accessory) into the board mount

hole.

Using an allen key, remove the main unit from the base.

Drill through the bushing of the wiring hole, pass the cable

through the hole, and secure the base to the wall.

Connect the cable to the terminal block (see Step 3-3).

Mount the main unit onto the base.

Cautions>>

When mounting the main unit, take care not to trap the

nylon wire loop. Also, take care not to get your fingers

caught.

Check to see that the various settings and operations are

correct.

Caution>>

When the red LED flashes after the power turns on,

this signifies that the system is warming up. Wait for

approximately 60 seconds.

INSTALLATION AND ANGLE ADJUSTMENT

(1)

(2)

(3)

(4)

(5)

(6)

3-2

Inside View of the Base

3-3

WIRING

*1: TAMPER terminals to be connected to a 24 hour supervisory loop.

Name Function

TROUBLE

OUTPUT

Trouble out is used for anti-masking signal. When

an object is placed close to the lens surface, for a

period of more than 20 seconds (approx.), the IR

anti-masking circuit will activate and generate a

trouble signal.

TAMPER

OUTPUT

It is detected when the cover is opened.

It is detected when the main unit is removed from

its base.

Anti-Rotation:

Damage sustained by the main unit is detected.

When the system power switch is turned on while

the cover is closed, the mounting position of the

main unit itself will be determined and stored in

memory after approximately 10 seconds. Then,

if the main unit is impacted in a horizontal or

vertical direction and if the position of the main

unit has changed, damage sustained by the main

unit will be detected. However, if you remove the

cover while keeping the system power turned on,

and if you close the cover again after correcting

the position of the main unit, the new position

of the main unit will be stored in memory after

approximately 10 seconds.

Waterproof seal

(Do not remove

this seal.)

Base

Bushing of wiring

hole

Open wiring cap

Main unit connector

Wall mounting hole

Bushing of wiring

hole

Wiring terminals

1 Loosen the

ﬁ xing screw

for the

base.

2 Open.

3 Unplug

the cable

connector.

4 Pull out.

POWER INPUT

TAMPER OUTPUT *1

ALARM OUTPUT (N.C.)

ALARM OUTPUT (N.O.)

TROUBLE OUTPUT

SPARE

4 Tighten and

secure the

ﬁ xing screw

for the base.

2 Connect the

connector.

3 Close.

1 Insert and

secure here.

Nylon

wire

loop

Distance from the ground to

the bottom of the template

must be between 2.3 m (7.6 ft.)

and 4 m (13 ft.).

CREEP

ALARM OUTPUT (N.C.)

ALARM OUTPUT (N.O.)

- 3 -

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL

DETECTION AREA SETTING

You can adjust the detection area by 90 degrees in a horizontal

direction and by 10 degrees in a vertical direction.

Correct the vertical detection angle according to the mounting

height of the sensor unit.

Applicable

models

SIP-3020/5 SIP-4010/5 SIP-404/5

10°

90° 90°

SIP-3020CAM

Cautions>>

To rotate the main unit counterclockwise, loosen the

RHside adjustment screw. To rotate the main unit

clockwise, loosen the LH-side adjustment screw.

Otherwise, you may find it difficult to tighten or you may

find that you cannot tighten the adjustment screw when

you are securing the main unit.

To rotate the unit counterclockwise

To rotate the unit clockwise

Power wires should not exceed the following lengths.

WIRE SIZE SIP-3020/5, SIP-4010/5, SIP-404/5

12V DC 14V DC 24V AC

0.33 mm2

(AWG22)

480

(1570)

640

(2100)

1370

(4490)

0.52 mm2

(AWG20)

760

(2490)

1010

(3310)

2160

(7090)

0.83 mm2

(AWG18)

1210

(3970)

1610

(5280)

3450

(11320)

m (ft.)

4-1

Main Detection Area Setting

Adjust the angle of the main unit in a horizontal direction so

that you can cover the desired detection area.

Adjust the angle of the main unit in a vertical direction so

that you can cover the desired detection area.

Cautions>>

If the mounting wall is at an angle, the arrow of the

main unit may exceed the top or bottom limit of “Angle

adjustment guide”. Always check this using the area

viewfinder or the walk tester. If the detection area is

too high or too low, an object outside the detection

area may be detected or incorrect object detection may

occur.

Remove the cover.

Cautions>>

The cover is linked to the main unit by nylon wire loop so

that the cover does not fall. Do not pull the cover using

excessive force.

(1)

(2)

(3)

When mounted at a height of

2.3 meters (7.6ft.)

When mounted at a height of

4.0 meters (13ft.)

3 Rotate the main unit.

2 Loosen the adjustment screw.

4 Tighten the adjustment screw slightly.

Hooks

3 Slide the cover downward

and release the hooks.

1 Loosen two ﬁ xing screws for

the cover and pull out the

cover until it stops.

Cover

2 Hold the heads of both cover ﬁ xing screws with your

hands, and pull down and remove the bottom section

of the cover from the main unit.

Adjustment

screw

Align the arrow of the main

unit with the “Angle adjustment

guide” of the adjustment

screw. The main unit is usually

adjusted within the width of this

guide.

1 Loosen the ﬁ xing screw

for the base.

Specyfikacje produktu

Marka:	Optex
Kategoria:	Niesklasyfikowane
Model:	SIP-3020
Regulowany termostat:	Nie
Częstotliwość wejściowa AC:	50 Hz
Napięcie wejściowe AC:	230 V
Wysokość produktu:	350 mm
Szerokość produktu:	300 mm
Głębokość produktu:	450 mm
Waga produktu:	6500 g
Układ:	Blad
Model:	Gril
Kółka:	Nie
Źródło ciepła:	Prąd elektryczny
Moc w sumie:	1800 W
nogi:	Nie
Wbudowana wydajność:	Nie
Pokrywka:	Nie