Instrukcja obsługi Optex AX-330PLUS

Optex Niesklasyfikowane AX-330PLUS

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Optex AX-330PLUS (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
INSTALLATION INSTRUCTIONS
PHOTOELECTRIC DETECTOR
AX-330PLUS
• LED indicator for beam alignment level:
Accurate and reliable alignment can be easily achieved by using LED indicator located on the receiver.
The alarm indicating lamp is located in the front end of the inner housing and in viewfinder.
• Aligned fine angle adjustment:
By turning the dial, you can achieve vertical and horizontal optical adjustments.
• Form C relay:
Suitable for various applications.
• Anti-frost structure:
The front cover prevents fog and condensation from blocking the beams.
• Beam interruption time adjustment:
This feature allows you to select suitable beam interruption time for any environment.
• Alignment-level monitor jack
• Optional accessories ( not included):
Heating unit (HU-2), Back cover (BC-2)
PHOTOELECTRIC DETECTOR
AX-330PLUS
FEATURES
Warning
Caution
• Read this instruction manual carefully prior to installation.
• After reading, store this manual carefully in an easily accessible place for reference.
• This manual uses the following warning indications for correct use of the product, harm to you or other people and damage to your assets, which
are described below. Be sure to understand the description before reading the rest of this manual.
INTRODUCTION
1
1-1 BEFORE YOUR OPERATION
Failure to follow the instructions provided with this indication and improper handling may cause
death or serious injury.
Failure to follow the instructions provided with this indication and improper handling may cause
injury and/or property damage.
This symbol indicates prohibition. The specific prohibited action is provided in and/or around the figure.
This symbol requires an action or gives an instruction.
Warning
Caution
Do not use the product for purposes other than the detection of moving objects such as
people and vehicles. Do not use the product to activate a shutter, etc., which may
cause an accident.
Do not touch the unit base or power terminals of the product with a wet hand (do not
touch when the product is wet with rain, etc.). It may cause electric shock.
Never attempt to disassemble or repair the product. It may cause fire or damage to the
devices.
Do not exceed the voltage or current rating specified for any of the terminals during
installation, doing so may cause fire or damage to the devices.
Do not pour water over the product with a bucket, hose, etc. The water may enter,
which may cause damage to the devices.
Clean and check the product periodically for safe use. If any problem is found, do not
attempt to use the product as it is and have the product repaired by a professional
engineer or electrician.
No.59-2709-0 1712-25
Detection range
AX-330PLUS
100 m / 330 ft.
Model
- 1 -
1-2 PRECAUTIONS
This symbol indicates prohibition. This symbol indicates recommendation.
Do not install the unit on an
unstable surface.
Do not install the unit in a location
where trees, leaves, or other objects
that may swing in the wind and block
the beam.
Do not install the receiver in a location
where it is exposed to direct sunlight.
1-3 PARTS IDENTIFICATION
The mounting pole should have a
solid basis with little movement at
the top of the pole.
Avoid aerial wiring. For indoor application, the wiring
installation is similar to that of
telephone wirings or the Internet.
For outdoor application, use wire
conduit as far as possible. Some
places require shielded wires or
underground wiring.
- 2 -
Mounting Plate
Unit Base
Front Cover
Cover Lock Screw
Wiring Knockout
Monitor Jack
Beam Interruption
Time Adjustment
Lens
Horizontal Alignment
Dial
Terminals
Alarm Indicator
(Receiver)
Transmitting Condition
(Transmitter)
View Finder
Vertical
Alignment Dial
Unit Base Mounting
Screw
U-Shaped Bracket
(accessory)
ACCESSORIES >>
U-Shaped brackets x 24×20 self tapping x 4 M4×14 screws x 4
2-1 Normal installation
INSTALLATION
2
1Range/ height/ angle 2Pole installation
2-2 Installing method
1
2
3
4
5
- 3 -
Mounting height;
0.7 to 1.0 m
(2.3 to 3.3 ft.)
Detection range;
100 m (330 ft.)
max.
Horizontal Vertical
180° (±90°)
10° (±5°) * Mounting pole; φ43~48 mm (1 11/16’’~1 7/8’’)
(Standard U.S. 1 1/2’’pipe)
* The length of wiring cable out of the pole;
within 0.6 m (2.0 ft.)
* After finishing the pole installation,
align the transmitter and receiver with each other.
Loosen the cover lock screw and
remove the front cover.
Pull out wires through the wiring
hole on the mounting plate and
fix the mounting plate on the wall
with screws.
Pole mounting Two unit mounting
( back to back)
Place the front cover after the optical
alignment and the walk test.
( Refer to optical alignment in Section 4).
Connect wires to the terminals.
(refer to Terminal and wiring
in Section 2-3).
Dig out a hole on the right
side of the rubber bushing
marked with , when it is◎
need for the second wire.
Pull the wires through the wiring holes of the unit base.
Connect the unit base to the mounting plate through the hook on the top of the unit base.
Push the unit base until it is fully engaged with the mounting plate.
Tighten the mounting screws on the bottom of the unit base.
Place the U-shaped bracket on the mounting
pole, and pull out wires through the wiring
hole on the mounting plate and fix the
mounting plate on the U-shaped bracket
with screws.
Fix two U-shaped brackets in layers on a pole, two
units can be mounted back-to-back on a pole at the
same height.
Wall mounting
Loosen the unit base mounting screw and
slide the mounting plate downwards relative
to the unit base to remove it.
Separating
Mounting
Wires and fixing
Connecting
Place the front cover
Tighten the cover lock screw.
about 0.6 m
(2.0 ft.)
about
1 m
(3.3 ft.)
about
0.1 m
(3.9 inch.)
Alignment angle;
Knockout for the second wire

Specyfikacje produktu

Marka: Optex
Kategoria: Niesklasyfikowane
Model: AX-330PLUS

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Optex AX-330PLUS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Optex

Optex

Optex AP2-20N Instrukcja

9 Października 2024
Optex

Optex CW-G2 Instrukcja

7 Października 2024
Optex

Optex WXS-RDAM Instrukcja

5 Października 2024
Optex

Optex OAM-DUAL T Instrukcja

5 Października 2024
Optex

Optex OM-105C Instrukcja

5 Października 2024
Optex

Optex WXS-DAM Instrukcja

5 Października 2024
Optex

Optex LX-802N Instrukcja

5 Października 2024
Optex

Optex REDWALL SIP-100-IP-BOX Instrukcja

5 Października 2024
Optex

Optex AX-330PLUS Instrukcja

2 Października 2024
Optex

Optex CDX-AM Instrukcja

29 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024