Instrukcja obsługi NUVO Castillo 60/382

NUVO Lampa Castillo 60/382

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla NUVO Castillo 60/382 (1 stron) w kategorii Lampa. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE
IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to
follow the steps in the order given. Under no circumstances
should a fixture be hung on house electrical wires, nor should a
swag type fixture be installed on a ceiling, which contains a
radiant type heating system. Read instructions carefully. If you
are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to misplace
any of the screws or parts, which are needed to install this
fixture.
STEP 1: Using two pairs of pliers to open one link on the end of
the chains (I) and attach the link to the loops (J),
repeat this step for the fixture loops (H).
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Secure the mounting bar (A) to outlet box with the
outlet box screws (B).Thread the nut (D) onto the
nipple (E) so that five threads are exposed above the
nut (D). Insert the lock washer (C) and thread the
nipple (E) into the mounting bar (A), then secure with
the nut (D).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 2: Lace wires up through chain (I) and pass wires through
holes in loop (H). We recommend lacing wire up
through every other link of chain (I).
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the ground
wire from the fixture (if supplied) around the green
grounding screw, then connect it to ground wire from
the outlet box (if not fixed on the outlet box) using a
wire connector (not supplied). If ground wire from the
fixture is not supplied, wrap the ground wire (if not
fixed on the outlet box) from the outlet box around the
green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and
connect the wires according to the directions below:
GROUP A: Connect to Black
House Wire
GROUP B: Connect to White
House Wire
BLACK WHITE
*PARALLEL WIRE (round &
smooth)
*PARALLEL WIRE (square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR GREY WITHOUT
TRACER
BROWN GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is round
in shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place
evenly against the black wire from the outlet box. Do
NOT twist wires together before using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the
connector clockwise until you feel a firmness.
STEP 5: Try gently to pull the connector off the wires. If you can
pull the connector off, carefully re-do steps 3 and 4, as
above, and check again for a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire
from the outlet box in the same manner. Make sure no
bare wires can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside
outlet box, Raise the canopy (F) and secure the
canopy (F) to mounting bar (A) with the nipple (E) and
the ball nut (G).
STEP 2: Place the glasses (L) and the caps (M) over the
sockets (K) and secure with the retaining rings (N).
STEP 3: Install lamps. (Please do not exceed the maximum
capacity recommended on the socket.)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
ITEM: 60/382


Specyfikacje produktu

Marka: NUVO
Kategoria: Lampa
Model: Castillo 60/382

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z NUVO Castillo 60/382, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Lampa NUVO

NUVO

NUVO Harlow 60/4630 Instrukcja

9 Października 2024
NUVO

NUVO Laguna 60/5925 Instrukcja

9 Października 2024
NUVO

NUVO Ballerina 60/181 Instrukcja

9 Października 2024
NUVO

NUVO Ballerina 60/188 Instrukcja

9 Października 2024
NUVO

NUVO Gemini 60/4759 Instrukcja

9 Października 2024
NUVO

NUVO Fusion 60/4689 Instrukcja

9 Października 2024
NUVO

NUVO Bridgeview 60/1703 Instrukcja

8 Października 2024
NUVO

NUVO Dupont 60/1822 Instrukcja

8 Października 2024
NUVO

NUVO Dupont 60/1842 Instrukcja

8 Października 2024
NUVO

NUVO Dupont 60/1823 Instrukcja

8 Października 2024

Instrukcje Lampa

Najnowsze instrukcje dla Lampa