Instrukcja obsługi Integral LED ILSTRGBWB028E
Integral LED
Lampa
ILSTRGBWB028E
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Integral LED ILSTRGBWB028E (4 stron) w kategorii Lampa. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4

Flexible 24V INTEGRAL LED RGBW Strip IP65
Installation Guide
Pour des instructions en français, merci de
vous rendre à l’adresse www.integral-led.
com an de les télécharger directement
depuis la page du produit (‘Product’ sur
le site) dans la section Téléchargement
(‘Download’)
IMPORTANT NOTICE
• This product should be installed according to the instructions in this guide and by a qualied electrical installer.
• All electrical work must be completed in accordance with the latest IET wiring regulations (formally IEE) for the UK or in accordance with all applicable
regulations and laws in the country in which it is being installed. This product falls under a low voltage Class circuit category.III
• Switch OFF power at the mains before installing the LED strip.
• S trip must only be installed indoors or in outdoor areas are sheltered. Unit is protected against water jets and dust. Not suitable for water immersion.
• Avoid looking directly at the strip when turned on, for a long period of time.
• Observe the operating temperature of the LED strip: -25C to +60C.
To avoid any damage to the LED strip or driver
• Always disconnect or switch o the power supply before cutting or connecting an LED strip. Wait at least one minute before connecting to a recently
powered driver.
• Always handle the LED strip with care.
• Observe the correct polarity for 24V connections (g 1).
• Safely route and secure all wires so they cannot be pinched or damaged.
• Do NOT power the strip whilst in its packaging reel.
• Do NOT twist the LED strip or heavily press down on the area above LEDs.
INTRODUCTION
• This installation guide is for exible, IP65 constant voltage self-adhesive LED strips produced by Integral LED.
• Depending on your installation, you can purchase additional accessories such as mounting clips.
A) CHOOSING A 24V LED DRIVER
• This LED strip operates with a 24V DC constant-voltage power supply known as a driver. Drivers are sold separately and are available in varying wattage outputs.
• The specication of the driver required will depend on the total power requirement of the connected strip(s). The power output of the driver (wattage
rating) must be at least 20% higher than the total required wattage of the strip(s) being powered.
For example, if you are installing 5 LED strips of 1M each and the power requirement of each 1M strip is 3W/metre – the total power requirement is 15W.
The power rating of the driver should be a least 20% above 15W i.e. A minimum of 18W
• Ensure the LED driver specication and IP rating is correct for your application.
B) PRE-INSTALLATION GUIDE
LED strips make a great addition to any domestic or commercial environment. They can change the mood and look of a space instantly and are very energy
ecient. The possibilities are endless so the requirement for each lighting project will be dierent.
It is worth taking some time to plan your project for the desired eect before removing the backing tape on the LED strip. The specication, length, mounting position
and distance from an object determines the appearance of a lit LED strip. You will also need to consider the placement and concealment, of the 24V LED driver, control
unit and wires and the power switch to turn the LED strip ON and OFF.
We recommend that you test the strip by temporarily holding the LED strip in place by using a suitable tape, such as masking tape. Safely connect the power
supply - you can then carefully move the strip to try dierent angles and positions to gain the desired illumination eect and position. Check for light spots,
reections and shadows.
Please consider the surface you are applying the LED strip to; the surface should be stable, clean and smooth. On removal of a xed LED strip - damage to
paint, wallpaper or other substrates may occur. Take care in measuring the length required before cutting the strip, take into account the space required for the
connection wires. You may also consider using a spirit level, plumb line or other guide if required.
In the bag
1 X 5M ±5cm IP65 INTEGRAL LED RGBW STRIP on reel pre-tted with an
appropriate connector to connect to a suitable control unit and power
supply.
IP65
WARNING
DO NOT CONNECT THE LED STRIP DIRECTLY TO A MAINS SUPPLY.
THE LED STRIP MUST ONLY BE CONNECTED TO A SUITABLE 24V LED DRIVER.

C) POWER SUPPLY CONFIGURATIONS AND WIRING
1) POWERING THE STRIP
The LED strip is powered by a suitable 24V LED driver. Ensure the power is OFF and that the correct
polarity is observed when wiring the LED driver (Fig 1).
2) VOLTAGE DROP
If the total length of LED strips powered by a single LED driver is too long, you may nd that the LEDs
furthest away from the driver will be unlit or dimmed. To avoid this you will need to use additional
drivers. For instance if you are powering 2 X 5M strips from one driver – you will need to split the run
into separate 5M runs each powered by its own driver.
D) PRECAUTIONS FOR INSTALLING THE INTEGRAL LED STRIP
1. Please check the bag contents before installation.
2. Do not remove the strip from the packaging until ready for installation.
3. Do NOT press on the LEDs or other components during installation (g 4).
4. Do not power the strip before completely releasing it from the reel.
5. Do not twist the LED strip (g 5).
6. Strip must only be installed indoors or in outdoor areas are sheltered. Unit is protected
against water jets and dust. Not suitable for water immersion.
7. If the product needs to be cut to length; please measure carefully and cut squarely at the
appropriate cut marks only using a sharp pair of scissors (g 6).
8. To x the LED strip to a smooth surface; the strip is pre-tted with 3M adhesive backing tape.
Ensure that the mounting surface is clean, dry and free from any oils, grease or wax.
9. The Integral LED strip has excellent exibility but requires the bending diameter to be no
smaller than 50 mm (g 7).
10. The strip is pre-tted with V+/R/G/B/W connection wires at one end. Check the supply
voltage and wire connections to control unit and LED driver before switching the power on.
CAUTION – Twisting, pressing on LEDs, over-bending the strip, cutting at non-cut points,
incorrectly powering the strip or not observing the conditions for the IP65 rating (see important
notice above) will invalidate the warranty (your statutory rights remain unaected).
E) INSTALLATION INSTRUCTIONS
1. To ensure a successful installation - please read the precautions and pre-installation
recommendations above.
2. The mounting surface must be clean, dry and free from dust or grease.
3. Release the LED strip from the package and unreel.
4. Measure and cut the LED strip to the required length (only cut at the cut marks with power
OFF). If strip needs to be cut, please see instructions below to seal the strip (F).
5. Remove the 3M self-adhesive backing tape from the strip gradually during installation.
Do not remove it all at once to avoid the strip becoming entangled and sticking to itself (gs
8 and 9).
6. Stick the LED strip to the mounting surface by pressing on the strip in between components
only. Do NOT press on the LEDs or other components on the strip.
7. Due to the weight of the strip, additional mounting clips must be applied to secure the
strip at aprox. 25cm intervals (g 10). Avoid covering the LEDs with the mounting clips. The
mounting clips are sold separately without screws and it is the responsibility of the installer
to select the correct type of screw depending on mounting substrate.
8. Once the strip is axed, it is then ready to be wired. Please see section C1.
F) CUTTING THE IP65 STRIP
The silicone (sold separately) is required to maintain the IP65 rating. For control, always apply the
nozzle ( cut the nozzle 4-5mm from the top). Wear protective gloves and eyewear. Always work on
a protected surface in case of spills. Work in a well-ventilated area. We recommend that the strip is
allowed to dry for 24hrs and 7 days to cure before subjecting the strip to water.
1) If the strip needs to be cut to length or into two or more lengths, all non-powered ends have
to be sealed using a silicone sealant.
a. Cut the non-powered end of the strip squarely with a sharp pair of scissors at the cut marks
Typical installation conguration
Straight run
An LED driver powers the control unit and the rst LED strip. Additional strips
can be connected in series. The installer will need to consider voltage drop
(see 2).
g 2
Powered from the centre
Power one or two equal lengths of LED strip from the centre.
This conguration will give the best results.
g 3
Additional accessories (sold separately) may be required for complex congurations.
D
2 0 0 - 2 4 0 V A C
D C + 24 v D C
N
L
D C - D C -
D C + V +
B
W
R
G
R
L E D 1
D R
D R
L E D 1
R
D
C) 1 (g 1) D = Driver, R = Receiver
C) 1 (g 2) D = Driver, R = Receiver
C) 1 (g 3) D = Driver, R = Receiver
Max Run = 5 Meters
D) 3 (g 4)
D) 5 (g 5)
D) 7 (g 6)
D) 9 (g 7)
E) 5 (g 9)
E) 5 (g 8)
>=50mm

only – ll the top with silicone using the nozzle. Then carefully ll the end of the strip. You
can use your gloved nger or a tool to make sure all gaps are lled and a good seal in made
(g 11).
2) All powered ends have to be sealed using a sillicone sealant and power wires
a. Cut the strip squarely with a sharp pair of scissors at the cut marks only. For the end to be
powered, carefully remove just enough of the silicone on the strip above the contacts to
solder on wires. Clean the contacts with emery paper and then solder on the power wires
using a good quality solder – Please pay attention to the polarity.
b. Once the wires have been soldered, carefully and safely apply power and control unit to
the strip to check the connections. Fill the top of stripe with silicone from the tube using
the nozzle. Make sure the gaps around the strip and the protruding wires are sealed using a
gloved nger or a tool . A heat shrink tube is recommended to apply and cover the soldering
part (g 12).
CAUTION: When applying connection wires to the strip, ensure that the correct polarity is
observed.
Always observe polarity for 24V connections to control unit, positive (+) to positive, red (R) to red,
green (G) to green, blue (B) to blue and white (W) to white.
Check the wire connections before switching the power on.
E) 7 (g 10)
F) 1 (g 11)
F) 2 (g 12)
Specyfikacje produktu
Marka: | Integral LED |
Kategoria: | Lampa |
Model: | ILSTRGBWB028E |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Integral LED ILSTRGBWB028E, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Lampa Integral LED

4 Kwietnia 2025

9 Października 2024

28 Września 2024

28 Września 2024
Instrukcje Lampa
- Lampa Sony
- Lampa Ikea
- Lampa Samsung
- Lampa LG
- Lampa Beurer
- Lampa Sanitas
- Lampa Xiaomi
- Lampa BeamZ
- Lampa TP-Link
- Lampa Milwaukee
- Lampa Philips
- Lampa Livoo
- Lampa JBL
- Lampa Thule
- Lampa Toolcraft
- Lampa Canon
- Lampa Mio
- Lampa Nedis
- Lampa Stanley
- Lampa OK
- Lampa Adler
- Lampa Westinghouse
- Lampa Fenix
- Lampa August
- Lampa Niceboy
- Lampa Einhell
- Lampa Prixton
- Lampa Silverline
- Lampa Mesko
- Lampa Honeywell
- Lampa Chauvet
- Lampa Steinel
- Lampa Makita
- Lampa Akasa
- Lampa ArmyTek
- Lampa Petzl
- Lampa Kodak
- Lampa Smart
- Lampa ORNO
- Lampa Dyson
- Lampa RYOBI
- Lampa Gembird
- Lampa Godox
- Lampa Chicco
- Lampa Medisana
- Lampa Deltaco
- Lampa Flex
- Lampa Konig & Meyer
- Lampa Trust
- Lampa DEDRA
- Lampa Hilti
- Lampa Digitus
- Lampa Cateye
- Lampa Vimar
- Lampa V-TAC
- Lampa Schneider
- Lampa Ledlenser
- Lampa Eurolite
- Lampa Eufy
- Lampa Emos
- Lampa NightStick
- Lampa Crivit
- Lampa Osram
- Lampa Viessmann
- Lampa Ansmann
- Lampa AVM
- Lampa Velleman
- Lampa Klarstein
- Lampa Güde
- Lampa Pyle
- Lampa Adviti
- Lampa Nordlux
- Lampa Camry
- Lampa Werma
- Lampa ARRI
- Lampa TriStar
- Lampa Ibiza Sound
- Lampa Florabest
- Lampa IVT
- Lampa Zhiyun
- Lampa Maginon
- Lampa Kanlux
- Lampa Brilliant
- Lampa Genie
- Lampa Brandson
- Lampa Rocktrail
- Lampa G3 Ferrari
- Lampa Axis
- Lampa Hayward
- Lampa NEO Tools
- Lampa Fuzzix
- Lampa Carson
- Lampa Innoliving
- Lampa Abus
- Lampa Bresser
- Lampa Livarno Lux
- Lampa Elro
- Lampa Hama
- Lampa Zafferano
- Lampa Duronic
- Lampa Cameo
- Lampa Barco
- Lampa Goobay
- Lampa GoPro
- Lampa Schwaiger
- Lampa Gravity
- Lampa COLBOR
- Lampa Elation
- Lampa GVM
- Lampa Denver
- Lampa Berger & Schröter
- Lampa Futurelight
- Lampa Nitecore
- Lampa Tracer
- Lampa Craftsman
- Lampa Vemer
- Lampa Olight
- Lampa Black Diamond
- Lampa Media-Tech
- Lampa Levenhuk
- Lampa BenQ
- Lampa Thermaltake
- Lampa Martin
- Lampa PowerPlus
- Lampa Vonroc
- Lampa Powerfix
- Lampa HiKOKI
- Lampa Workzone
- Lampa EasyMaxx
- Lampa Ikan
- Lampa Alecto
- Lampa Avidsen
- Lampa Impact
- Lampa Aputure
- Lampa Dörr
- Lampa SLV
- Lampa Karma
- Lampa Smartwares
- Lampa Elgato
- Lampa Metabo
- Lampa Adj
- Lampa ETC
- Lampa Sygonix
- Lampa Cotech
- Lampa Savio
- Lampa Profoto
- Lampa Qazqa
- Lampa ATN
- Lampa Intermatic
- Lampa Brennenstuhl
- Lampa KonstSmide
- Lampa Eglo
- Lampa Lucide
- Lampa Eminent
- Lampa Nordride
- Lampa Hähnel
- Lampa Silva
- Lampa Sylvania
- Lampa Steren
- Lampa Hansa
- Lampa Exagerate
- Lampa Lumie
- Lampa Livarno
- Lampa Royal Sovereign
- Lampa Melinera
- Lampa In Lite
- Lampa Maul
- Lampa Näve
- Lampa Luceplan
- Lampa InFocus
- Lampa Massive
- Lampa Hombli
- Lampa Runtastic
- Lampa Steinhauer
- Lampa Topeak
- Lampa Zuiver
- Lampa Konig
- Lampa X4-Tech
- Lampa Genaray
- Lampa Hella
- Lampa HQ
- Lampa Nanlite
- Lampa Trio Lighting
- Lampa Ranex
- Lampa Globo
- Lampa Dutchbone
- Lampa Paul Neuhaus
- Lampa Neewer
- Lampa Meross
- Lampa Artecta
- Lampa ColorKey
- Lampa Xoro
- Lampa Laserworld
- Lampa Ozone
- Lampa Garden Lights
- Lampa Eufab
- Lampa Unilux
- Lampa Artemide
- Lampa Batavia
- Lampa Panzeri
- Lampa Honeycomb
- Lampa Elinchrom
- Lampa Auray
- Lampa Mission
- Lampa Paulmann
- Lampa Pixel
- Lampa GAO
- Lampa Wetelux
- Lampa Sagitter
- Lampa Esotec
- Lampa Fabas
- Lampa Neo
- Lampa Ozocozy
- Lampa Hatco
- Lampa DLG
- Lampa Goal Zero
- Lampa Lutec
- Lampa Ibiza Light
- Lampa Beghelli
- Lampa Polarlite
- Lampa Claypaky
- Lampa Lightway
- Lampa Broncolor
- Lampa NUVO
- Lampa Omnilux
- Lampa Digital Juice
- Lampa UMAGE
- Lampa Markslöjd
- Lampa Angler
- Lampa Luxform
- Lampa Velamp
- Lampa Lalumi
- Lampa ActiveJet
- Lampa Graypants
- Lampa Raya
- Lampa Rutec
- Lampa Luxo
- Lampa Kartell
- Lampa Rotolight
- Lampa Lightaccents
- Lampa SIGOR
- Lampa King Mungo
- Lampa DPM
- Lampa Maxim
- Lampa Oecolux
- Lampa Megatron
- Lampa WiZ
- Lampa Casalux
- Lampa Briloner
- Lampa Frandsen
- Lampa Luctra
- Lampa Lowel
- Lampa Airam
- Lampa Lirio By Philips
- Lampa Westcott
- Lampa Gewiss
- Lampa SecoRüt
- Lampa Fabas Luce
- Lampa Dainolite
- Lampa Signature Design By Ashley
- Lampa Videx
- Lampa Louis Poulsen
- Lampa Fixpoint
- Lampa Kind LED
- Lampa ET2
- Lampa Quoizel
- Lampa Golden Lighting
- Lampa Ridem
- Lampa Fredrick Ramond
- Lampa Crystorama
- Lampa Sonneman
- Lampa AFX
- Lampa Currey & Company
- Lampa Deko-Light
- Lampa Livex Lighting
- Lampa Hinkley Lighting
- Lampa Norwell
- Lampa Nicols
- Lampa Physa
- Lampa Allegri
- Lampa Craftmade
- Lampa Falcon Eyes
- Lampa Yeelight
- Lampa Schonbek
Najnowsze instrukcje dla Lampa

4 Kwietnia 2025

4 Kwietnia 2025

4 Kwietnia 2025

4 Kwietnia 2025

4 Kwietnia 2025

4 Kwietnia 2025

4 Kwietnia 2025

4 Kwietnia 2025

3 Kwietnia 2025

3 Kwietnia 2025