Instrukcja obsługi Netgear ProSafe WAC740

Netgear Punkt dostępu ProSafe WAC740

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Netgear ProSafe WAC740 (2 stron) w kategorii Punkt dostępu. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Installation
NETGEAR ProSAFE Dual Band Wireless AC
Access Point
WAC740
Set Up the Access Point
Before mounting the access point in a high location, first set up and test the
access point to verify WiFi network connectivity.
IMPORTANT: You can deploy the WAC740 access point only in a WiFi
network that is managed by a ProSAFE wireless controller.
¾To cable the access point:
1. Connect an Ethernet cable from LAN port 1 on the access point to a
LAN port on a PoE+ switch, that is, an 802.3at-compatible switch.
2. Connect an Ethernet cable from the PoE+ switch to an Ethernet port on
the computer.
3. Check the LEDs to verify that the access point is set up correctly.
LED Description
Power LED
•O. Power is o.
•Solid green. Power is on.
•Alternating green and amber. The access point is receiving insucient
PoE power.
•Solid amber, then blinking amber. A self-test is running or firmware is
being loaded. During startup, the Power LED first lights solid amber, then
goes o, and then blinks amber before turning solid green aer about
one minute. If aer two minutes the Power LED remains solid amber or
continues to blink amber, it indicates a system fault.
Activity LED
•O. No link with the network is detected.
•Solid green. A link with the network is detected.
•Blinking green. Network trac is detected.
Package Contents
Unpack the box and verify the contents:
• WAC740 ProSAFE Dual Band Wireless AC Access Point
• Category 5e Ethernet cable
• Ceiling mount kit
LED Description
LAN LED 1
•O. A 10 Mbps Ethernet link is detected or no Ethernet link is detected.
•Solid green. A 2.5 Gbps Ethernet link is detected.
•Solid amber. A 1 Gbps or 100 Mbps Ethernet link is detected.
If both LAN LED 1 and LAN LED 2 light solid green or amber, the LAN ports
are members of a link aggregation group (LAG).
LAN LED 2
•O. No LAG is detected.
•Solid green. A LAG with a 2.5 Gbps Ethernet link is detected.
•Solid amber. A LAG with a 1 Gbps or 100 Mbps Ethernet link is detected.
If both LAN LED 1 and LAN LED 2 light solid green or amber, the LAN ports
are members of a LAG.
2.4G WLAN LED
•O. The 2.4 GHz WiFi radio is o.
•Solid green. The 2.4 GHz WiFi radio is on.
•Blinking green. WiFi activity is detected on the 2.4 GHz WiFi radio.
5G WLAN LED
•O. The 5 GHz WiFi radio is o.
•Solid green. The 5 GHz WiFi radio is on.
•Blinking green. WiFi activity is detected on the 5 GHz WiFi radio.
The access point uses a DHCP client that is enabled by default. If your network
includes a DHCP server, the access point obtains an IP address from the DHCP
server. If your network does not include a DHCP server, the access point sets
its IP address to a static IP address of 192.168.0.160.
If your network includes a DHCP server, note the following:
• Make sure that Option 43 is enabled on the DHCP server.
• Make sure that the DHCP server specifies the IP address of the wireless
controller in the required hexadecimal format in the Option 43 field.
For example, if the IP address of the wireless controller is 192.168.0.250,
you must enter the hexadecimal string 02:04:C0:A8:0:FA.
To compose the address, start with 02:04: and then add each of the four
address octets in hexadecimal format, separated by colons.
The first two octets (02:04) define a standalone NETGEAR wireless
controller, or in a stack, the first wireless controller in the stack.
July 2016
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo
are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
NETGEAR INTL LTD
Building 3, University Technology Centre
Curraheen Road, Cork, Ireland
To specify the second wireless controller in the stack, enter the first two
octets as 02:08. To specify the third wireless controller in the stack,
enter the first two octets as 02:0C.
The remaining four octets specify the IP address in hexadecimal format.
• We recommend that you reserve an IP address for the access point on
the DHCP server.
If your network does not include a DHCP server, configure a computer with
a static IP address of 192.168.0.210 and a subnet mask of 255.255.255.0
so that you can connect to the access point at IP address 192.168.0.160.
¾To verify that the access point obtained IP address information,
or if your network does not include a DHCP server, to configure
the access point’s IP address information:
1. Open a web browser from a computer that is connected to the same
network as the access point or to the access point directly through an
Ethernet cable.
2. In the address bar, enter the IP address of the access point.
The default IP address is .192.168.0.160
A login window displays.
3. Enter the user name and password.
The user name is . The default password is admin password. The user
name and password are case-sensitive.
4. Select Configuration > System > Basic > Network Settings > IP
Settings.
5. Verify or configure the IP settings for your network.
6. Select Configuration > System > Network Settings > Controller
Settings.
7. Verify or configure the IP address for the wireless controller in the
network.
For more information, see the ProSAFE wireless controller user manual.
Problem Cause Possible Solution
No LEDs are lit
on the access
point.
The access point
is receiving no
power.
•Make sure that the access point is securely connected to a PoE+ switch.
•Make sure that the PoE+ switch is connected to a power source.
The Power
LED alternates
green and
amber.
The access point
is receiving
insucient PoE
power.
•Make sure that PoE+ switch is not overloaded.
•If you connected the access point to a PoE (802.3af) switch, disconnect
it and connect it to a PoE+ (802.3at) switch instead. The access point
requires a PoE+ (802.3at) switch.
The LAN port
LEDs are o.
A hardware
connection
problem exists.
•Make sure that the cable is connected to LAN port 1 (the PoE port) on
the access point. (LAN port 2 active only when a LAG is enabled.)
•Make sure that the cable connectors are securely plugged into the
access point and switch.
• Make sure that the switch is turned on.
The WLAN
LEDs are o.
The wireless
connection does
not work.
•Make sure that the PoE+ switch is providing sucient power to the
access point.
•From the wireless controller, verify that the radio or radios are turned on.
•If the WLAN LEDs remain o, contact NETGEAR.
You cannot
connect to
the access
point from a
browser.
Multiple
possible causes.
•Make sure that your computer is using an IP address in the same
range as the access point. The access point default IP address is
192.168.0.160, and the default subnet mask is 255.255.255.0.
•Quit the browser, clear the cache, delete the cookies, and launch the
browser again.
Support
Thank you for purchasing this NETGEAR product. You can visit
www.netgear.com/support to register your product, get help, access the latest
downloads and user manuals, and join our community. We recommend that you
use only ocial NETGEAR support resources.
For more information about the installation options, visit
www.netgear.com/support to access the hardware installation guide.
For the current EU Declaration of Conformity, visit
http://support.netgear.com/app/answers/detail/a_id/11621/.
For regulatory compliance information, visit
http://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
¾To let the wireless controller discover the access point:
1. Access the wireless controller at its network IP address.
2. Select Access Point > Discovery Wizard.
3. Follow the steps onscreen to discover the access point and review the
discovery results.
4. In the table with discovered access points, select the check box for the
access point, and click the button.Add
The access point is added to the Managed AP List and is now ready for
further configuration and management by the wireless controller.
For more information, see the ProSAFE wireless controller user manual.
Deploy the Access Point
The best location for the access point is elevated, such as mounted on a
wall or ceiling, at the center of the WiFi coverage area, and within line of
sight of all mobile devices.
For information about mounting the access point, see the ceiling and wall
installation guide for the WAC720, WAC730, and WAC740 access points.
¾To deploy the access point:
1. Disconnect the access point and position it where you will deploy it.
2. Connect an Ethernet cable from the access point to a LAN port on a
PoE+ switch.
3. Make sure that the PoE+ switch and the wireless controller are
connected.
4. Using a WiFi device, verify connectivity by connecting to the access
point and use a browser to connect to the Internet.
Troubleshooting Tips
The following table provides some tips for correcting simple problems
that you might encounter. For more troubleshooting information, see the
troubleshooting chapter in the ProSAFE wireless controller user manual.

Specyfikacje produktu

Marka: Netgear
Kategoria: Punkt dostępu
Model: ProSafe WAC740

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Netgear ProSafe WAC740, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Punkt dostępu Netgear

Netgear

Netgear WNDAP360 Instrukcja

12 Października 2024
Netgear

Netgear WG103 Instrukcja

19 Września 2024
Netgear

Netgear ProSAFE WN203 Instrukcja

30 Sierpnia 2024
Netgear

Netgear WAC120 Instrukcja

30 Sierpnia 2024
Netgear

Netgear ProSafe WAC740 Instrukcja

21 Sierpnia 2024
Netgear

Netgear WAC540 Instrukcja

19 Sierpnia 2024
Netgear

Netgear WN604 Instrukcja

14 Sierpnia 2024
Netgear

Netgear WN370 Instrukcja

14 Sierpnia 2024
Netgear

Netgear ProSafe WG102 Instrukcja

8 Sierpnia 2024
Netgear

Netgear WNHDB3004 Instrukcja

4 Lipca 2024

Instrukcje Punkt dostępu

Najnowsze instrukcje dla Punkt dostępu

Cisco

Cisco MR12 Instrukcja

14 Października 2024
Draytek

Draytek VigorAP 920R Instrukcja

13 Października 2024
TP-Link

TP-Link Festa F65-Wall Instrukcja

9 Października 2024
D-Link

D-Link DWL-1000AP+ Instrukcja

9 Października 2024
D-Link

D-Link DWL-700AP Instrukcja

9 Października 2024
Cambium Networks

Cambium Networks cnPilot e505 Instrukcja

9 Października 2024
Cambium Networks

Cambium Networks cnPilot e425H Instrukcja

9 Października 2024
Cambium Networks

Cambium Networks cnPilot e600 Instrukcja

9 Października 2024
Cambium Networks

Cambium Networks cnPilot e510 Instrukcja

9 Października 2024
Cambium Networks

Cambium Networks cnPilot e502S Instrukcja

9 Października 2024