Instrukcja obsługi Mtx Audio TX480D

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mtx Audio TX480D (32 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/32
TX480D TX6500D TX81000D
Owner’s Manual
Designed by MTX in Phoenix, AZ - USA
mtxaudio.eu facebook.com/MTXEuropetwitter.com/MTXEurope
Sub
Outputs
12VREMGND
Gain
Fan
6V - 0,2V
+12V GND
OnOff
Bridge Mode
Master Slave
EBC
Remote
Data
Link
Subsonic Low Pass
40Hz - 150Hz
High Level
Inputs
Ch.2
Ch.1
12VREMGND
X-over
HP-OFF-LP
HP-OFF-LP
Gain
6V - 0,2V
6V - 0,2V
40Hz - 400Hz
Frequency
40Hz - 400Hz
Ch.1 Ch.2
Ch.3 Ch.4
Ch.1
Bridge
Ch.2
Ch.3
Bridge
Ch.4
Ch.1 Ch.2 Ch.3 Ch.4
High Level
Inputs
Ch.1
Ch.3 Ch.4
Ch.2
Fan
+12V GND
Settings, Power and Speaker connections :
TX81000D Specifications :
Mono block class-D amplifier
CEA2006 certified Power Output :
- 1x 1000 Watts RMS @ 2Ω and THD+N ≤1%
- 1x 600 Watts RMS @ 4Ω and THD+N ≤1%
Crossover :
- Low pass 24dB/oct variable from 40Hz to 150Hz
- Subsonic filter 24dB/oct at 30Hz
Signal-to-Noise Ratio (1 Watt) : > 75dB
THD+Noise (Distortion) (1 Watt) : ≤ 0,1%
Frequency Response (±0,5dB) : 10Hz-150Hz
Maximum Input Signal : 6V
Maximum Sensitivity : 100mV
EBC remote control
Bridged mode with gain management
Thermoregulated fan connector for an external fan(s)
Dimensions : 366mm x 133mm x 54mm
TX81000D TX6500D TX480D
Thank you for purchasing an MTX Audio High-End TX amplifier. Proper installation matched with MTX speakers and subwoofers provide superi-
or sound and performance for endless hours of waking the neighbors. Congrats and enjoy the ultimate audio experience with MTX !
TX480D Specifications :
4-Channel Class-D wide range amplifier
CEA2006 certified Power Output :
- 4x 140 Watts RMS @ 2Ω and THD+N ≤1%
- 4x 80 Watts RMS @ 4Ω and THD+N ≤1%
- 2x 280 Watts RMS bridged at 4Ω and THD+N ≤1%
Crossover :
- High pass 12dB/oct variable from 40Hz to 400Hz
- Low pass 12dB/oct variable from 40Hz to 400Hz
Signal-to-Noise Ratio (1 Watt) : > 85dB
THD+Noise (Distortion) (1 Watt) : ≤ 0,05%
Frequency Response (±1dB) : 10Hz-40000Hz
Maximum Input Signal : 6V
Maximum Sensitivity : 200mV
Thermoregulated fan connector for an external fan
Dimensions : 216mm x 133mm x 54mm
Thank You !
Specifications :
TX6500D Specifications :
Mono block class-D amplifier
CEA2006 certified Power Output :
- 1x 500 Watts RMS @ 2Ω and THD+N ≤1%
- 1x 300 Watts RMS @ 4Ω and THD+N ≤1%
Crossover :
- Low pass 24dB/oct variable from 40Hz to 150Hz
- Subsonic filter 24dB/oct at 30Hz
Signal-to-Noise Ratio (1 Watt) : > 75dB
THD+Noise (Distortion) (1 Watt) : ≤ 0,1%
Frequency Response (±0,5dB) : 10Hz-150Hz
Maximum Input Signal : 6V
Maximum Sensitivity : 100mV
EBC remote control
Bridged mode with gain management
Thermoregulated fan connector for an external fan(s)
Dimensions : 266mm x 133mm x 54mm
Top View
Ground Terminal (GND) - A proper ground is required for your amplifier to operate at peak performance. A short ground cable the same diameter as the power cable
should be used to attach the ground terminal directly to the chassis of the vehicle. Always remove paint, dirt or debris to expose bare metal where the ground cable
will be attached.
Remote Terminal (REM) - The amplifier can be turned on by applying 12 volts to this terminal. Typically this voltage is supplied by a wire from the source unit marked
“remote” or “power antenna”.
+12V Power Terminal (12V) - This is the main power input for the amplifier and must be connected directly to the positive terminal of the vehicles battery for proper
operation. Use caution when installing (+12) power cable in the vehicle. Avoid running this cable parallel with RCA cables, antennas, or other sensitive equipment
due to massive currents that can induce noise into the audio system. It is also very important to have a tight, secure connection for maximum performance. MTX
recommends using 50mm
2 power wire with the MTX RFL4001D amplifier.
Speaker Terminals TX81000D TX6500D (Sub outputs) : Connect your subwoofer(s) to these terminals. If using two subwoofers or a dual voice coil subwoofer, respect
the phase (+) together, (-) together...
Speaker Terminals TX480D : Connect the speakers to these terminals. Observe speaker polarity throughout the system. Improper phase can result in loss of bass
response and/or poor overall sound quality.
Bridge Mode :
When bridging the amplifier, use the Ch1 positive terminal and the Ch2 negative terminal only.
When bridging the amplifier, use the Ch3 positive terminal and the Ch4 negative terminal only.
Warning : do not bridge the amplifier with an impedance lower than 4Ω.
RCA Inputs (Ch.1 Ch.2 Ch.3 Ch.4) - These RCA inputs are used with head units that have RCA or Line level outputs (head units need a minimum level of 200mV output
for proper operation of the amplifier). MTX recommends only high quality RCA cables to decrease the possibility of radiated noise entering the system.
Gain Control (Gain) - The gain control matches the input sensitivity of the amplifier to the head unit being used. The operating range varies from 0,2 to 6V.
Adjusting the gain
1. Turn the gain control on the amplifier all the way down (counter clockwise).
2. Turn up the volume control on the head unit to approximately 3⁄4 of maximum.
3. Adjust the gain control on the amplifier until audible distortion occurs.
4. Adjust the gain control down until audible distortion disappears.
5. The amplifier is now calibrated to the output of the head unit.
Subsonic Switch (Subsonic) - Used to switch the subsonic filter on or off. The subsonic filter frequency is set to 20Hz. The subsonic filter protects subwoofer(s) against
low frequencies that can cause damage. Very useful with vented enclosures.
Low Pass X-Over Frequency Control - Used to select the desired low-pass (LP) x-over frequency. The frequency is adjustable from 40Hz to 150Hz.
Bridge mode Switch - Used to put the amp in Master mode or Slave mode when bridging two RFL4001D’s. For more details, see Master/Slave Mode section.
EBC Port (External Bass Control) - The Remote Subwoofer Level Control (EBC) plugs directly into this port, while the EBC itself can be placed anywhere in the vehicle
for on demand bass adjustments. EBC is included.
Data link Port (Data Link) : Used to connect two TX81000D or two TX6500D in bridge mode and used in Master/Slave mode. The RJ15 cable is included. For more
detail see Master/Slave mode section.
12V thermoregulated fan connector for one or two 12V external cooling fans (Attention : 0,5A max - two fans max). The harness is included.
High level inputs (HLI) : This input will allow the amplifier to operate from source units with speaker-level outputs. Output speaker leads from the source unit should
be tied directly to the wire harness provided with the amplifier. Please respect the polarity to get the maximum sound quality.
Note : When speaker level inputs are used, a remote turn on wire must be used to switch the amplifier on and off.
X-Over Switch (X-Over) :
In “LP position, the active low pass (LP) x-over is turned on. Use this position for subwoofer application.
In “HP position, the active high pass (HP) x-over is turned on. Use this position for speaker application.
In “O position, the x-over is turned off. The amp is in wide range mode.
X-Over Frequency Control (Frequency) : Used to select the desired x-over frequency. The frequency is adjustable from 0Hz to 400Hz.
PowerOn/Protection LED :
1. The LED illuminates red when the amp is switched on.
2. The LED is flashing red when the outputs are is in short circuit, when the impedance is too low (2Ω minimum), when the amp is in thermal protection .

Specyfikacje produktu

Marka: Mtx Audio
Kategoria: Radia samochodowe
Model: TX480D

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mtx Audio TX480D, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Radia samochodowe Mtx Audio

Mtx Audio

Mtx Audio TX2450 Instrukcja

15 Września 2024
Mtx Audio

Mtx Audio TR275 Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio TX81000D Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio TX480D Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio RFL5300 Instrukcja

11 Września 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

JVC

JVC KD-R90BT Instrukcja

15 Października 2024
Kenwood

Kenwood KMM-X705 Instrukcja

15 Października 2024
Alpine

Alpine CDM-7870R Instrukcja

14 Października 2024
Hyundai

Hyundai H-CMD2009 Instrukcja

14 Października 2024
Dual

Dual XC4100 Instrukcja

13 Października 2024
Audiovox

Audiovox VXE 3010 Instrukcja

13 Października 2024
MB Quart

MB Quart PAB 5400 Instrukcja

13 Października 2024
Hyundai

Hyundai H-CDM8023 Instrukcja

13 Października 2024
Caliber

Caliber RCD110B Instrukcja

13 Października 2024
JVC

JVC KD-X30 Instrukcja

13 Października 2024