Instrukcja obsługi Mtx Audio TR275


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mtx Audio TR275 (36 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/36
mtxaudio.eu facebook.com/MTXEuropetwitter.com/MTXEurope
TR275
2-channel Class-AB Amplifier
660W Peak - 2x75W RMS
Designed by MTX in Phoenix, AZ - USA
TR450
4-channel Class-AB Amplifier
900W Peak - 4x50W RMS
Settings, Power and Speaker connections :
TR275
TR275
TR450
TR450
Thank you for purchasing an MTX Audio TR amplifier. Proper installation matched with MTX speakers and subwoofers provide superior sound
and performance for endless hours of waking the neighbors. Congrats and enjoy the ultimate audio experience with MTX !
Thank You !
Specifications :
Specifications :
• 4-Channel Class-AB wide range amplifier
• CEA2006 certified Power Output :
- 4x75W RMS @2Ω and THD+N ≤1%
- 4x50W RMS @4Ω and THD+N ≤1%
- 2x150W RMS bridged @4Ω and THD+N ≤1%
• Crossover :
- High pass 12dB/oct 80Hz
- Low pass 12dB/oct 80Hz
• Signal-to-Noise Ratio (1 Watt) : > 73dB
THD+Noise (Distortion) (1 Watt) : ≤ 0,2%
• Frequency Response (±1dB) : 10Hz-60000Hz
• Maximum Input Signal : 6V
• Maximum Sensitivity : 200mV
• Dimensions : 182x134x51mm
• High level inputs
• Optional EBC remote control (EBC-1)
Specifications :
• 2-channel Class-AB wide range amplifier
• CEA2006 certified Power Output :
- 2x110W RMS @2Ω and THD+N ≤1%
- 2x75W RMS @4Ω and THD+N ≤1%
- 1x220W RMS bridged @4Ω and THD+N ≤1%
• Crossover :
- High pass 12dB/oct 80Hz
- Low pass 12dB/oct 80Hz
• Signal-to-Noise Ratio (1 Watt) : > 74dB
THD+Noise (Distortion) (1 Watt) : ≤ 0,18%
• Frequency Response (±1dB) : 10Hz-60000Hz
• Maximum Input Signal : 6V
• Maximum Sensitivity : 200mV
• Dimensions : 142x134x51mm
• High level inputs
• Optional EBC remote control (EBC-1)
RCA Inputs (Input) : These RCA inputs are used with source units that have RCA or Line level outputs. (Source units need a minimum level of
200mV output for proper operation of the amplifier).
MTX recommends only high quality twisted pair cables (such as MTX ZNX) to decrease the possibility of radiated noise entering the system.
Gain Control (Gain) : The gain control matches the input sensitivity of the amplifier to the source unit being used. The operating range varies
from 200mv to 6V.
TR275 TR450
Adjusting the gain
1. Turn the gain control on the amplifier all the way down (counter clockwise).
2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.
3. Adjust the gain control on the amplifier until audible distortion occurs.
4. Adjust the gain control down until audible distortion disappears.
5. The amplifier is now calibrated to the output of the source unit.
X-Over Switch (X-Over) :
In “LP” position, the active low pass (LP) x-over is turned on to 80Hz 12dB/Oct. Use this position for subwoofer application.
In “HP position, the active high pass (HP) x-over is turned on to 80Hz 12dB/Oct. Use this position for speaker application.
In “Off position, the x-over is turned off. The amp is in wide range mode.
Speaker level inputs (High Inputs) : This input will allow the amplifier to operate from source units with speaker-level outputs. Output speaker
leads from the source unit should be tied directly to the wire harness provided with the amplifier.
Note : When speaker level inputs are used, a remote turn on wire must used to switch the amplifier on and off.
External Bass Control Port (Remote) - The Subwoofer Level Control Remote (EBC) plugs directly into this port, while the EBC itself can be placed
anywhere in the vehicle for on demand bass adjustments. Attention, the EBC is optional. You can purchase it separately (Reference : EBC-1).
PowerOn LED (Power) : The LED illuminates green when the amp is switched on.
Protection LED (Protec.) : The LED illuminates red when the amp is in short circuit or thermal protection.
Ground Terminal (GND) : A proper ground is required for your amplifier to operate at peak performance. A short ground cable the same diameter
as the power cable should be used to attach the ground terminal directly to the chassis of the vehicle. Always remove paint, dirt or debris to
expose bare metal where the ground will be attached.
Remote Terminal (REM) : The amplifier can be turned on by applying 12 volts to this terminal. Typically this voltage is supplied by a wire from
the source unit marked “remote” or power antenna”.
(+12V) Power Terminal (12V) : This is the main power in ut for the amplifier and must be connected directly to the positive terminal of the p
vehicles battery for proper operation. Use caution when installing (+12) power cable in the vehicle. Avoid running this cable parallel with RCA
cables, antennas, or other sensitive equipment due to massive currents that can induce noise into the audio system. It is also very important
to have a tight, secure connection for maximum performance. MTX recommends using 8~10mm power wire with the MTX TR275 and TR450.
Speaker Terminals (Speaker Output) : Connect speakers to these terminals. Ensure correct polarity, positive-to-positive (+/+) and negative-to-
negative (-/-). Reversing the polarity strongly degrades the bass level and the sound quality.
Bridge Mode :
TR275 : When bridging the amplifier, use the Ch.1 positive terminal and the Ch.2 negative terminal only.
TR450 : When bridging the amplifier, for the two first channels, use the Ch.1 positive terminal and the Ch.2 negative terminal only. For the two
following channels, take the Ch.3 positive terminal and the Ch.4 negative terminal.
Warning : do not bridge the amplifier with an impedance lower than 4Ω.


Specyfikacje produktu

Marka: Mtx Audio
Kategoria: Radia samochodowe
Model: TR275

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mtx Audio TR275, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Radia samochodowe Mtx Audio

Mtx Audio

Mtx Audio TH902 Instrukcja

16 Września 2024
Mtx Audio

Mtx Audio TX6500D Instrukcja

16 Września 2024
Mtx Audio

Mtx Audio RT50.4M Instrukcja

16 Września 2024
Mtx Audio

Mtx Audio TX2450 Instrukcja

15 Września 2024
Mtx Audio

Mtx Audio re-Q Instrukcja

15 Września 2024
Mtx Audio

Mtx Audio TR275 Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio TX81000D Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio TX480D Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio X1000D Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio RT60-2 Instrukcja

13 Września 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

JVC

JVC KD-R90BT Instrukcja

15 Października 2024
Kenwood

Kenwood KMM-X705 Instrukcja

15 Października 2024
Alpine

Alpine CDM-7870R Instrukcja

14 Października 2024
Hyundai

Hyundai H-CMD2009 Instrukcja

14 Października 2024
Dual

Dual XC4100 Instrukcja

13 Października 2024
Audiovox

Audiovox VXE 3010 Instrukcja

13 Października 2024
MB Quart

MB Quart PAB 5400 Instrukcja

13 Października 2024
Hyundai

Hyundai H-CDM8023 Instrukcja

13 Października 2024
Caliber

Caliber RCD110B Instrukcja

13 Października 2024
JVC

JVC KD-X30 Instrukcja

13 Października 2024