Instrukcja obsługi Mtx Audio RT60-2

Mtx Audio Radia samochodowe RT60-2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mtx Audio RT60-2 (44 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/44

RT60

2-Channel Class-AB Power Ampliﬁer

540W

MAX

www.mtxaudio.com

www.mtxaudio.eu

SPEAKER

BRIDGE

R+

R- L+ L-

GND REM +12V FUSE

POWER

LINE OUT LINE IN

HLI

+ R - G - L +

GAIN X-OVER LPFHPFR

6V 0,1V 40Hz 400Hz

FULL

HPF LPF 40Hz 400Hz

www.mtxaudio.com - www.mtxaudio.eu

Owner’s Manual - RT60.2

Introduction

Thank you for purchasing an MTX Audio Hi-Performance ampliﬁer. Proper installation matched with MTX speak-

ers and subwoofers provide superior sound and performance for endless hours of waking the neighbors, slam-

min' your friends or ﬂat out stomping wanna-be players. Congrats and enjoy the ultimate audio experience with

MTX !

Speciﬁcations :

• 2-Channel Class-AB Amplier

• CEA2006 certied Power Output :

- 90 watts RMS x 2-channel at 2 ohm and THD+N ≤1%

- 60 watts RMS x 2-channel at 4 ohm and THD+N ≤1%

- 180 watts RMS x 1-channel at 4 ohm and THD+N ≤1%

• Crossover :

- High pass 12dB/oct variable from 40Hz to 400Hz

- Low pass 12dB/oct variable from 40Hz to 400Hz

• Signal-to-Noise Ratio (1 watt) : > 80dB

• THD+Noise (Distortion) (1 watt) : ≤ 1%

• Frequency Response (±1dB) : 20Hz-30000Hz

• Maximum Input Signal : 6V

• Maximum Sensitivity : 100mV

• Dimensions : 310mm x 180mm x 55mm

• High level inputs

Control Panel

Control Panel :

Gain Control (GAIN) : The gain control matches the input sensitivity of the amplier to the source unit being used.

The operating range varies from 100mv to 6V.

Adjusting the gain

1. Turn the gain control on the amplier all the way down (counter clockwise).

2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.

3. Adjust the gain control on the amplier until audible distortion occurs.

4. Adjust the gain control down until audible distortion disappears.

5. The amplier is now calibrated to the output of the source unit.

Low-Pass High-Pass X-Over Switch (X-OVER) :

In “LPF” position, the active low pass (LP) x-over is turned on

In “HPF” position, the active high pass (HP) x-over is turned on

In “FULL” position, the x-over is turned o

High Pass X-Over Frequency Control (HPF) :

Used to select the desired high-pass (HP) x-over frequency. The frequency is adjustable from 40Hz to 400Hz..

Low Pass X-Over Frequency Control (LPF) :

Used to select the desired low-pass (LP) x-over frequency. The frequency is adjustable from 40Hz to 400Hz..

RCA Inputs (LOW INPUT) : These RCA inputs are used with source units that have RCA or Line level outputs.

(Source units need a minimum level of 100mV output for proper operation of the amplier).

MTX recommends only high quality twisted pair cables (such as StreetWires) to decrease the possibility of radi-

ated noise entering the system.

RCA outputs - These RCA output jacks are for connecting multiple ampliers to 1 stereo RCA lead coming

from the source unit (daisy chaining).

PowerOn/Protection LED - The LED illuminates red when the amp is switched on. When the amps is in shortcir-

cuit or thermal protection, the LED is blinking.

Speaker level inputs (HLI) :

This input will allow the amplier to operate from source units with speaker-level outputs. Output speaker leads

from the source unit should be tied directly to the wire harness provided with the ampliﬁer.

Note : When speaker level inputs are used, a remote turn on wire must used to switch the amplier on and o.

(+12V) Power Terminal : This is the main power input for the amplier and must be connected directly to the

positive terminal of the vehicles battery for proper operation. Use caution when installing (+12) power cable

in the vehicle. Avoid running this cable parallel with RCA cables, antennas, or other sensitive equipment due to

massive currents that can induce noise into the audio system. It is also very important to have a tight, secure con-

nection for maximum performance. MTX recommends using 10mm

2 power wire with the MTX RT60.2 amplier.

Remote Terminal (REM) : The amplier can be turned on by applying 12 volts to this terminal. Typically this volt-

age is supplied by a wire from the source unit marked “remote” or “power antenna”.

Ground Terminal (GND) : A proper ground is required for your amplier to operate at peak performance. A short

ground cable the same diameter as the power cable should be used to attach the ground terminal directly to

the chassis of the vehicle. Always remove paint, dirt or debris to expose bare metal where the ground will be

attached.

Speaker Terminals (SPEAKER) : Connect speakers to these terminals. Observe speaker polarity throughout the

system. Improper phase can result in loss of bass response and/or poor overall sound quality.

Bridge Mode : When bridging the amplier, use the right positive terminal and the left negative terminal only.

Warning : do not bridge the amplier with an impedance lower than 4 ohm.

Fuse (FUSE) : When fuse blow, replace them with the same value. Never use a higher rated fuse !

Specyfikacje produktu

Marka:	Mtx Audio
Kategoria:	Radia samochodowe
Model:	RT60-2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mtx Audio RT60-2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Radia samochodowe Mtx Audio

Mtx Audio TH902 Instrukcja

16 Września 2024

Mtx Audio TX6500D Instrukcja

16 Września 2024

Mtx Audio RT50.4M Instrukcja

16 Września 2024

Mtx Audio TX2450 Instrukcja

15 Września 2024

Mtx Audio re-Q Instrukcja

15 Września 2024

Mtx Audio TR275 Instrukcja

14 Września 2024

Mtx Audio TX81000D Instrukcja

14 Września 2024

Mtx Audio TX480D Instrukcja

14 Września 2024

Mtx Audio X1000D Instrukcja

14 Września 2024

Mtx Audio RT60-2 Instrukcja

13 Września 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

JVC KD-R90BT Instrukcja

15 Października 2024

Kenwood KMM-X705 Instrukcja

15 Października 2024

Alpine CDM-7870R Instrukcja

14 Października 2024

Hyundai H-CMD2009 Instrukcja

14 Października 2024

Dual XC4100 Instrukcja

13 Października 2024

Audiovox VXE 3010 Instrukcja

13 Października 2024

MB Quart PAB 5400 Instrukcja

13 Października 2024

Hyundai H-CDM8023 Instrukcja

13 Października 2024

Caliber RCD110B Instrukcja

13 Października 2024

JVC KD-X30 Instrukcja

13 Października 2024