Instrukcja obsługi Mtx Audio TR450

Mtx Audio Radia samochodowe TR450

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mtx Audio TR450 (36 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/36

mtxaudio.eu facebook.com/MTXEuropetwitter.com/MTXEurope

TR275

2-channel Class-AB Ampliﬁer

660W Peak - 2x75W RMS

TR450

4-channel Class-AB Ampliﬁer

900W Peak - 4x50W RMS

Settings, Power and Speaker connections :

TR275

TR450

Thank you for purchasing an MTX Audio TR ampliﬁer. Proper installation matched with MTX speakers and subwoofers provide superior sound

and performance for endless hours of waking the neighbors. Congrats and enjoy the ultimate audio experience with MTX !

Thank You !

Speciﬁcations :

• 4-Channel Class-AB wide range ampliﬁer

• CEA2006 certiﬁed Power Output :

- 4x75W RMS @2Ω and THD+N ≤1%

- 4x50W RMS @4Ω and THD+N ≤1%

- 2x150W RMS bridged @4Ω and THD+N ≤1%

• Crossover :

- High pass 12dB/oct 80Hz

- Low pass 12dB/oct 80Hz

• Signal-to-Noise Ratio (1 Watt) : > 73dB

• THD+Noise (Distortion) (1 Watt) : ≤ 0,2%

• Frequency Response (±1dB) : 10Hz-60000Hz

• Maximum Input Signal : 6V

• Maximum Sensitivity : 200mV

• Dimensions : 182x134x51mm

• High level inputs

• Optional EBC remote control (EBC-1)

Speciﬁcations :

• 2-channel Class-AB wide range ampliﬁer

• CEA2006 certiﬁed Power Output :

- 2x110W RMS @2Ω and THD+N ≤1%

- 2x75W RMS @4Ω and THD+N ≤1%

- 1x220W RMS bridged @4Ω and THD+N ≤1%

• Crossover :

- High pass 12dB/oct 80Hz

- Low pass 12dB/oct 80Hz

• Signal-to-Noise Ratio (1 Watt) : > 74dB

• THD+Noise (Distortion) (1 Watt) : ≤ 0,18%

• Frequency Response (±1dB) : 10Hz-60000Hz

• Maximum Input Signal : 6V

• Maximum Sensitivity : 200mV

• Dimensions : 142x134x51mm

• High level inputs

• Optional EBC remote control (EBC-1)

RCA Inputs (Input) : These RCA inputs are used with source units that have RCA or Line level outputs. (Source units need a minimum level of

200mV output for proper operation of the ampliﬁer).

MTX recommends only high quality twisted pair cables (such as MTX ZNX) to decrease the possibility of radiated noise entering the system.

Gain Control (Gain) : The gain control matches the input sensitivity of the ampliﬁer to the source unit being used. The operating range varies

from 200mv to 6V.

TR275 TR450

Adjusting the gain

1. Turn the gain control on the ampliﬁer all the way down (counter clockwise).

2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.

3. Adjust the gain control on the ampliﬁer until audible distortion occurs.

4. Adjust the gain control down until audible distortion disappears.

5. The ampliﬁer is now calibrated to the output of the source unit.

X-Over Switch (X-Over) :

In “LP” position, the active low pass (LP) x-over is turned on to 80Hz 12dB/Oct. Use this position for subwoofer application.

In “HP” position, the active high pass (HP) x-over is turned on to 80Hz 12dB/Oct. Use this position for speaker application.

In “Oﬀ” position, the x-over is turned oﬀ. The amp is in wide range mode.

Speaker level inputs (High Inputs) : This input will allow the ampliﬁer to operate from source units with speaker-level outputs. Output speaker

leads from the source unit should be tied directly to the wire harness provided with the ampliﬁer.

Note : When speaker level inputs are used, a remote turn on wire must used to switch the ampliﬁer on and oﬀ.

External Bass Control Port (Remote) - The Subwoofer Level Control Remote (EBC) plugs directly into this port, while the EBC itself can be placed

anywhere in the vehicle for on demand bass adjustments. Attention, the EBC is optional. You can purchase it separately (Reference : EBC-1).

PowerOn LED (Power) : The LED illuminates green when the amp is switched on.

Protection LED (Protec.) : The LED illuminates red when the amp is in short circuit or thermal protection.

Ground Terminal (GND) : A proper ground is required for your ampliﬁer to operate at peak performance. A short ground cable the same diameter

as the power cable should be used to attach the ground terminal directly to the chassis of the vehicle. Always remove paint, dirt or debris to

expose bare metal where the ground will be attached.

Remote Terminal (REM) : The ampliﬁer can be turned on by applying 12 volts to this terminal. Typically this voltage is supplied by a wire from

the source unit marked “remote” or “power antenna”.

(+12V) Power Terminal (12V) : This is the main power in ut for the ampliﬁer and must be connected directly to the positive terminal of the p

vehicles battery for proper operation. Use caution when installing (+12) power cable in the vehicle. Avoid running this cable parallel with RCA

cables, antennas, or other sensitive equipment due to massive currents that can induce noise into the audio system. It is also very important

to have a tight, secure connection for maximum performance. MTX recommends using 8~10mm power wire with the MTX TR275 and TR450.

Speaker Terminals (Speaker Output) : Connect speakers to these terminals. Ensure correct polarity, positive-to-positive (+/+) and negative-to-

negative (-/-). Reversing the polarity strongly degrades the bass level and the sound quality.

Bridge Mode :

TR275 : When bridging the ampliﬁer, use the Ch.1 positive terminal and the Ch.2 negative terminal only.

TR450 : When bridging the ampliﬁer, for the two ﬁrst channels, use the Ch.1 positive terminal and the Ch.2 negative terminal only. For the two

following channels, take the Ch.3 positive terminal and the Ch.4 negative terminal.

Warning : do not bridge the ampliﬁer with an impedance lower than 4Ω.

Specyfikacje produktu

Marka:	Mtx Audio
Kategoria:	Radia samochodowe
Model:	TR450

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mtx Audio TR450, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Radia samochodowe Mtx Audio

Mtx Audio TH902 Instrukcja

16 Września 2024

Mtx Audio TX6500D Instrukcja

16 Września 2024

Mtx Audio RT50.4M Instrukcja

16 Września 2024

Mtx Audio TX2450 Instrukcja

15 Września 2024

Mtx Audio re-Q Instrukcja

15 Września 2024

Mtx Audio TR275 Instrukcja

14 Września 2024

Mtx Audio TX81000D Instrukcja

14 Września 2024

Mtx Audio TX480D Instrukcja

14 Września 2024

Mtx Audio X1000D Instrukcja

14 Września 2024

Mtx Audio RT60-2 Instrukcja

13 Września 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

JVC KD-R90BT Instrukcja

15 Października 2024

Kenwood KMM-X705 Instrukcja

15 Października 2024

Alpine CDM-7870R Instrukcja

14 Października 2024

Hyundai H-CMD2009 Instrukcja

14 Października 2024

Dual XC4100 Instrukcja

13 Października 2024

Audiovox VXE 3010 Instrukcja

13 Października 2024

MB Quart PAB 5400 Instrukcja

13 Października 2024

Hyundai H-CDM8023 Instrukcja

13 Października 2024

Caliber RCD110B Instrukcja

13 Października 2024

JVC KD-X30 Instrukcja

13 Października 2024