Instrukcja obsługi Mtx Audio RFL5300


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mtx Audio RFL5300 (40 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/40
mtxaudio.eu
RFL5300
5 Channel Class-AB Power Amplifier
850W RMS CEA
Owners Manual - MTX RFL5300
Thank You !
Thank you for purchasing an MTX Audio High-End amplifier. Proper installation matched with MTX speakers and subwoofers provide
superior sound and performance for endless hours of waking the neighbors, slammin your friends or flat out stomping wanna-be
players. Congrats and enjoy the ultimate audio experience with MTX !
Specifications :
• 5-Channel Class-AB amplifier
• CEA2006 certified Power Output :
Channels 1, 2, 3, 4
- 120 Watts RMS x 4-channels at 2 ohm and THD+N ≤1%
- 80 Watts RMS x 4-channels at 4 ohm and THD+N ≤1%
- 240 Watts RMS bridged x 2 at 4 ohm and THD+N ≤1%
Channel 5
- 370 Watts RMS x 1-channel at 2 ohm and THD+N ≤1%
- 250 Watts RMS x 1-channel at 4 ohm and THD+N ≤1%
• Crossover :
Channels 1, 2
- High pass 12dB/oct variable from 40Hz to 5000Hz
Channels 3, 4
- Low pass 12dB/oct variable from 800Hz to 5000Hz
- High pass 12dB/oct variable from 40Hz to 800Hz
- Band pass 12dB/oct variable from 40Hz to 5000Hz
Channel 5
- Low pass 24dB/oct variable from 40Hz to 800Hz
• Signal-to-Noise Ratio (1 Watt) : > 98dB
• THD+Noise (Distortion) (1 Watt) : ≤ 0,05%
• Frequency Response (±1dB) : 10Hz-90000Hz
• Maximum Input Signal : 6V
• Maximum Sensitivity : 200mV
• Phase switch 0° or 180°
• EBC remote control
• Dimensions : 626mm x 204mm x 59mm
RCA Inputs - These RCA inputs are used with head units that have RCA or Line level outputs (head units need a minimum level of
200mV output for proper operation of the amplifier).
MTX recommends only high quality RCA cables to decrease the possibility of radiated noise entering the system.
Gain Control - The gain control matches the input sensitivity of the amplifier to the head unit being used. The operating range varies
from 200mv to 6V.
Adjusting the gain
1. Turn the gain control on the amplifier all the way down (counter clockwise).
2. Turn up the volume control on the head unit to approximately 3⁄4 of maximum.
3. Adjust the gain control on the amplifier until audible distortion occurs.
4. Adjust the gain control down until audible distortion disappears.
5. The amplifier is now calibrated to the output of the head unit.
High Pass X-Over Switch - Used to turn on the active high-pass (HP) x-over on and off. When engaged (On) the x-over is “ON”, when
disengaged (Off) the x-over is “OFF”.
High Pass X-Over Frequency Control - Used to select the desired high-pass (HP) x-over frequency. The frequency is adjustable from
40Hz to 5000Hz (Ch1, Ch2). The frequency is adjustable from 40Hz to 800Hz (Ch3, Ch4).
Low Pass X-Over Switch - Turns the active low pass (LP) x-over on and off. When engaged (On) the x-over is “ON, when disengaged
(Off) the x-over is “OFF”
Low Pass X-Over Frequency Control - Used to select the desired low-pass (LP) x-over frequency. The frequency is adjustable from 800Hz
to 5000Hz (Ch3, Ch4). The frequency is adjustable from 40Hz to 800Hz (Ch5).
Band Pass X-Over : To use, turn “ON” the LP (3) and HP (5) x-overs at the same time, creating a band-pass x-over for kick woofers or
midranges. You can tune the filter with frequency controls (4) and (6).
Input Switch : If the head unit is equipped with 4 RCA outputs (2 front and 2 rear), use the ch-3 ch-4 mode and connect the 4 RCA
outputs to the ch-1 ch-2 ch-3 ch-4 RCA inputs on the amp. If only 2 RCA outputs are available from the head unit, use the ch-1 ch-2
mode and connect the RCA outputs to the ch-1 and ch-2 inputs of the amp.
Input Switch channel 5 : If the head unit is equipped with a dedicated subwoofer output, use the ch-5 mode connect the RCA from the
subwoofer output to the subwoofer ch-5 RCA inputs on the amp. If no dedicated subwoofer output is available from the headunit use
the ch1 - ch2 mode, the channel 5 will take the signal from ch-1 and ch-2 RCA inputs on the amp.
Phase switch - Used to match the bass from subwoofers and front speakers. Toggle the phase switch from 0° to 180°. Keep the loudest
bass response.
EBC Port (External Bass Control) - The Remote Subwoofer Level Control (EBC) plugs directly into this port, while the EBC itself can be
placed anywhere in the vehicle for on demand bass adjustments. EBC is included.
Controls and Inputs :


Specyfikacje produktu

Marka: Mtx Audio
Kategoria: Radia samochodowe
Model: RFL5300

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mtx Audio RFL5300, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Radia samochodowe Mtx Audio

Mtx Audio

Mtx Audio TH902 Instrukcja

16 Września 2024
Mtx Audio

Mtx Audio TX6500D Instrukcja

16 Września 2024
Mtx Audio

Mtx Audio RT50.4M Instrukcja

16 Września 2024
Mtx Audio

Mtx Audio TX2450 Instrukcja

15 Września 2024
Mtx Audio

Mtx Audio re-Q Instrukcja

15 Września 2024
Mtx Audio

Mtx Audio TR275 Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio TX81000D Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio TX480D Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio X1000D Instrukcja

14 Września 2024
Mtx Audio

Mtx Audio RT60-2 Instrukcja

13 Września 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

JVC

JVC KD-R90BT Instrukcja

15 Października 2024
Kenwood

Kenwood KMM-X705 Instrukcja

15 Października 2024
Alpine

Alpine CDM-7870R Instrukcja

14 Października 2024
Hyundai

Hyundai H-CMD2009 Instrukcja

14 Października 2024
Dual

Dual XC4100 Instrukcja

13 Października 2024
Audiovox

Audiovox VXE 3010 Instrukcja

13 Października 2024
MB Quart

MB Quart PAB 5400 Instrukcja

13 Października 2024
Hyundai

Hyundai H-CDM8023 Instrukcja

13 Października 2024
Caliber

Caliber RCD110B Instrukcja

13 Października 2024
JVC

JVC KD-X30 Instrukcja

13 Października 2024