Instrukcja obsługi Mikrotik RBMAPL-2ND

Mikrotik Punkt dostępu RBMAPL-2ND

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mikrotik RBMAPL-2ND (4 stron) w kategorii Punkt dostępu. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

RouterBOARD mAP lite

Quick Setup Guide and Warranty Information

The mAP is a small AP device with one ethernet port, the Ethernet port supports powering by PoE.

First use

1. Plug the included USB power adapter into the power socket, and connect the USB cable to the mAP lite

2. Connect your Internet cable to the mAP lite Ethernet port

3. Wireless AP mode is enabled by default, you can connect from your computer to the SSID “MikroTik”. Log

into the mAP router from your web browser by opening 192.168.88.1 in the address bar

Powering

The device accepts powering from the USB port or from the Ethernet port:

micro USB power jack accepts 5V DC, a USB 5V adapter is included with the product

The Ethernet port accepts passive Power over Ethernet 11-57V DC.

The Ethernet port also accepts PoE power from a 802.3af switch over the pins +4,5/-7,8 or +3,6/-1,2

Under maximum load, the power consumption of this device is 4W.

Booting process

The device is preinstalled with MikroTik RouterOS software. It can be configured in several ways.

This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernet

cable. Connect to wireless SSID “MikroTik” and open in your web browser. Username is 192.168.88.1 admin

and there is no password. In case IP connection is not available, Winbox can be used to connect to the MAC

address of the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup

In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button

of the device when starting it until the LED light turns off, then release the button and the device will start

looking for Netinstall servers.

By default, the device is preconfigured with a simple firewall on the WAN port, this configuration can be viewed

when first connecting to the Router via Winbox. It will ask whether to keep this configuration or clean it to use

your own. LAN/WLAN ports have DHCP server enabled.

Extension Slots and Ports

One 10/100 Ethernet port, supporting automatic cross/straight cable connection (Auto MDI/X), so you

can use either straight or cross-over cables for connecting to other network devices.

One Integrated Wireless 2.4GHz 802.11b/g/n 2x2 MIMO, Onboard PIF antennas, max gain 2dBi

One microUSB 2.0 port for powering only

Resetting the device

In case you wish to return the device to its original configuration, you can use the RESET button. Hold this button

during boot time until LED lights start flashing, then release the button to Youreset RouterOS configuration.

can use this procedure if you have forgotten the password to access the device, or simply wish to return the unit

to its default configuration state.

See www.routerboard.com for more informaon. Contact for support quesons. 9-Sep-15support@mikrok.com

Buttons and Jumpers

1. Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS

configuration (total 5 seconds)

2. Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10

seconds)

3. Or Keep holding the button for 5 more seconds until until LED turns off, then release it to make the

RouterBOARD look for Netinstall servers (total 15 seconds)

Operating System Support

Currently tested operating system is MikroTik RouterOS starting from version 6.30

reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD,

RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks

appearing in this document are the property of their respective holders.

Hardware. MikroTik warrants all RouterBOARD series equipment for the term of twelve (12) months from the

shipping date to be free of defects in materials and workmanship under normal use and service, except in case of

damage caused by mechanical, electrical or other accidental or intended damages caused by improper use or due

to wind, rain, fire or other acts of nature.

To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization)

procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA

process.

1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding

all warranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly

from MikroTik in Latvia.

2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made for:

CCR1016-12G, CCR1016-12G-BU, CCR1036-12G-4S, RB1100, RB1100AH, RB1100AHx2, RB1200, RB600,

RB600A and RB800 as a paid service (fees apply).

3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the

sender at sender's cost. If the customer has not organized return of such rejected devices within 12 months

from the day of arrival, MikroTik has the right to discard them.

RMA Instructions are located on our webpage here: http://rma.mikrotik.com

This document is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited

to, the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made

every effort to ensure the accuracy of the contents of this document, however, it is possible that it may contain

technical inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this

publication, nor for direct or indirect, incidental, consequential or other damages that may result from such an

inaccuracy, including, but not limited to, loss of data or profits. Please report any inaccuracies found to

support@mikrotik.com

See www.routerboard.com for more informaon. Contact for support quesons. 9-Sep-15support@mikrok.com

Federal Communication Commission Interference Statement

(FCC ID: )TV7RBMAP2N

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This device and its antenna must not be co-located or operation in conjunction with any other antenna or

transmitter.

IMPORTANT: Exposure to Radio Frequency Radiation.

23 cm minimum distance has to be maintained between the antenna and the occupational user and 75 cm to

general public. Under such configuration, the FCC radiation exposure limits set forth for an

population/uncontrolled environment can be satisfied.

See www.routerboard.com for more informaon. Contact for support quesons. 9-Sep-15support@mikrok.com

Specyfikacje produktu

Marka:	Mikrotik
Kategoria:	Punkt dostępu
Model:	RBMAPL-2ND

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mikrotik RBMAPL-2ND, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Punkt dostępu Mikrotik

Mikrotik Wireless Wire Instrukcja

8 Grudnia 2024

Mikrotik WAP R Instrukcja

8 Grudnia 2024

Mikrotik OmniTIK 5 PoE ac Instrukcja

30 Września 2024

Mikrotik Audience LTE6 kit Instrukcja

29 Września 2024

Mikrotik Cube Lite60 Instrukcja

27 Września 2024

Mikrotik LtAP mini Instrukcja

25 Września 2024

Mikrotik hAP ac² Instrukcja

23 Września 2024

Mikrotik LHG XL HP5 Instrukcja

14 Września 2024

Mikrotik HAP ac lite Instrukcja

8 Września 2024

Mikrotik RBMAPL-2ND Instrukcja

5 Września 2024

Instrukcje Punkt dostępu

Najnowsze instrukcje dla Punkt dostępu

TP-Link RE6000XD Instrukcja

4 Grudnia 2024

Cisco MR12 Instrukcja

14 Października 2024

Draytek VigorAP 920R Instrukcja

13 Października 2024

Netgear WNDAP360 Instrukcja

12 Października 2024

TP-Link Festa F65-Wall Instrukcja

9 Października 2024

D-Link DWL-1000AP+ Instrukcja

9 Października 2024

D-Link DWL-700AP Instrukcja

9 Października 2024

Cambium Networks cnPilot e505 Instrukcja

9 Października 2024

Cambium Networks cnPilot e425H Instrukcja

9 Października 2024

Cambium Networks cnPilot e600 Instrukcja

9 Października 2024