Instrukcja obsługi Meliconi SPEEDY 2 COMBO

Meliconi Zdalne sterowanie SPEEDY 2 COMBO

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Meliconi SPEEDY 2 COMBO (4 stron) w kategorii Zdalne sterowanie. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
17
This universal remote control has the essential functions for the simplified use of an analogue or a digital
television combined with a satellite or terrestrial decoder - without having to switch between one appliance and
another. The dark blue buttons transmit the commands to the decoder while the light blue buttons control the
functions that correspond to the TV. If used with a digital TV, all the buttons control the same appliance.
BUTTON AND FUNCTION USE
FITTING THE BATTERIES
GB
Before programming and using the remote control, fit the batteries.
The remote control requires 2 new 1.5 V AAA/LR03 alkaline batteries. Insert the batteries as shown:
• The batteries must be changed once a year.
• Replace the batteries if the indicator light on the remote control starts to
flash during use. The batteries are low.
• This remote control has a permanent memory and does not lose the
programmed codes when the batteries are removed.
• Make a note of the code for your appliances on the adhesive label found
inside the battery cover. This note will be handy if you have to reprogram
your remote control.
Warning: do not expose the remote control to sources of excessive heat
Keep your Instructions Booklet for future reference.
To select the next programme.
Interrupts and restores the TV audio.
To reduce the TV's audio volume.
Numeric keypad.
Indicator light.
Button to exit the Teletext
and return to normal viewing.
TV ON button which is occasionally
needed to turn the TV on
To increase the TV's audio volume.
To select an external input
terminal to the TV.
Button to access the Teletext.
To select the previous programme.
ON/OFF to turn OFF the TV
and in some cases to turn it ON.
Thank you for choosing MELICONI.
OFF to turn the decoder off (STB).
18
HOW TO PROGRAMME THE REMOTE CONTROL
- - Turn on the TV and select a programme.
- Simultaneously hold down the and buttons for 5 seconds until the upper indicator light starts to flash
indicating that the remote control is in the programming state.
- Release the buttons and enter the code 0001 within 12 seconds. The indicator light begins flashing more
quickly, indicating that the remote control is ready for the search.
- Point the remote control towards the TV. Press and slowly release the button several times, stopping when
the appliance goes off (you may need to press the button a few dozen times).
- When the appliance goes off, press the button to confirm. Three long flashes indicate that the
operation has been completed successfully.
To command your appliances, you must programme your Speedy 2 COMBO as described in the next
paragraph. For those who can connect to the internet website www.meliconi.com, you will find interactive
instructions for a faster and easier programming of your remote control.
PREPARE FOR USE
Read these instructions carefully before programming your remote control!
- Turn on the appliance and select a programme.
- Simultaneously hold down the and buttons for 5 seconds until the upper indicator light starts to flash
indicating that the remote control is in the programming state.
- Release the buttons and enter the code 0001 within 12 seconds. The indicator light begins flashing more
quickly, indicating that the remote control is ready for the search.
- Point the remote control towards the appliance. Press and slowly release the button several times,
stopping when the appliance goes off (you may need to press the button a few dozen times).
- When the appliance goes off, press the button to confirm. Three long flashes indicate that the
operation has been completed successfully.
- Turn on the TV and select a programme.
- Turn on the TV and select a programme and buttons for 5 seconds until the upper indicator light
starts to flash indicating that the remote control is in the programming state.
- buttons for 5 seconds until the upper indicator light starts to flash indicating that the remote control is in the
programming state.
- Point the remote control towards the appliance. Press and slowly release the button several times,
stopping when the appliance goes off (you may need to press the button a few dozen times).
- When the appliance goes off, press the button to confirm. Three long flashes indicate that the
operation has been completed successfully.
If you have an analogue TV and an external decoder, follow procedure A and then procedure B. Follow procedure
C if you have a digital TV.
Additional check
Check that some of the other buttons, corresponding to those on your original remote control, work correctly.
If the commands function incorrectly or erratically, you have probably entered a code for a similar but different
remote control. In this case, repeat the search procedure starting from point 3.
ANALOGUE TV PROGRAMMING
DECODER PROGRAMMING
DIGITAL TV PROGRAMMING
19
Remember to always make a note of the 4-digit codes for your appliances on the inside of the battery cover
when the code search and saving are finished. The codes will be required if the remote control needs to be
re-programmed following accidental deletion.
To find the code for your remote control:
1. Simultaneously press and hold for 5 seconds the buttons corresponding to the appliance for which you
would like to enter the code: and for the analogue TV, and for the decoder, or and
for the digital TV, until the indicator light starts to flash indicating that the remote control is in the
programming state.
2. Upon release insert the code number you noted beforehand. Three flashes indicate that the code has been
memorized correctly. If not, try the code entry procedure again starting from point 1.
PROGRAMMED CODE NOTING
RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN
1. Simultaneously hold down the and buttons for 5 seconds (if you want to know the codes for the
analogue or digital TV), or and (if you want to know the code for the decoder), until the indicator
light starts to flash indicating that the remote control is in the programming state.
2. Release the buttons and press and release the button within 8 seconds.
3. After a short pause, the indicator light produces four series of flashes with a space between them,
corresponding to the code you are looking for. Count the number of flashes; each series of flashes
corresponds to one figure in the code. 10 flashes correspond to 0. For example, the code 1306 corresponds
to:
= 1
= 3
= 0
= 6
4. Make a note of the code on the adhesive label inside the battery cover for quick and easy consultation.
Identify and take note of the code which you have discovered
following the code noting procedure
(see “PROGRAMMED CODE NOTING” section).
NOTE: The indicator light flashes more quickly during the search operation.
The indicator light stops flashing and the remote control exits the programming mode in the following
cases:
• if no buttons are pressed for 12 seconds
• if the end of the code search list has been reached. In this case, consult the website
www.meliconi.com.

Specyfikacje produktu

Marka: Meliconi
Kategoria: Zdalne sterowanie
Model: SPEEDY 2 COMBO

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Meliconi SPEEDY 2 COMBO, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Zdalne sterowanie Meliconi

Meliconi

Meliconi fully 8 Instrukcja

12 Stycznia 2025
Meliconi

Meliconi Personal 2 plus Instrukcja

30 Września 2024
Meliconi

Meliconi gumbody light facile Instrukcja

23 Września 2024
Meliconi

Meliconi Speedy 2.1 Instrukcja

22 Września 2024
Meliconi

Meliconi GumBody Light Instrukcja

22 Września 2024
Meliconi

Meliconi universal 4 Instrukcja

22 Września 2024
Meliconi

Meliconi Pratico 2.1 Instrukcja

21 Września 2024
Meliconi

Meliconi Gumbody Personal 7 plus Instrukcja

21 Września 2024
Meliconi

Meliconi Gumbody Personal 2 Instrukcja

21 Września 2024
Meliconi

Meliconi Control TV+ Instrukcja

21 Września 2024

Instrukcje Zdalne sterowanie

Najnowsze instrukcje dla Zdalne sterowanie

Panasonic

Panasonic EUR7502XC0EG Instrukcja

15 Stycznia 2025
Delta

Delta GT 9000 Instrukcja

15 Stycznia 2025
Eminent

Eminent EM1041 Instrukcja

15 Stycznia 2025
Sonos

Sonos Controller for Android-smartphones Instrukcja

15 Stycznia 2025
Sonos

Sonos Controller voor Mac of pc Instrukcja

14 Stycznia 2025
Sonos

Sonos Controller for Android Tablets Instrukcja

14 Stycznia 2025
One For All

One For All URC 7935 Instrukcja

14 Stycznia 2025
Sonos

Sonos Controller for iPad Instrukcja

14 Stycznia 2025
SilverCrest

SilverCrest KH 2155 Instrukcja

12 Stycznia 2025
Hama

Hama Spot-Pointer V2 Instrukcja

11 Stycznia 2025