Instrukcja obsługi Meliconi Gumbody Personal 6 plus

Meliconi Zdalne sterowanie Gumbody Personal 6 plus

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Meliconi Gumbody Personal 6 plus (5 stron) w kategorii Zdalne sterowanie. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/5
Personal 6 plus
Thank you for choosing a Meliconi remote control.
The Personal 6 plus remote control is designed to command digital television sets. a TELEFUNKEN
Its ergonomic shape and soft rubber body make it easy to grip and protect it from shocks and drops.
By LEARN function, you can capture and store infrared signals from other remotes and match at will to one or more buttons.
The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio
frequency (e.g. voice commands and pointers) are not supported.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
The remote control requires 2 new 1.5V AAA/LR03 alkaline batteries, not included in the
package. Insert with the correct polarity as shown in gure.
DO NOT use batteries. rechargeable
BATTERIES TEST: Press and hold the 5 button and check that the LED remains on
continuously until the button is released. If the light is o or blinks, the inserted batteries are low,
therefore they need replacement.
If the remote control can control the TV correctly, it is to set a it matched. not essential specic code,
Identify the specic code and set it into the remote control using one of the following ways:
MANUAL
SEARCH
SMARTPHONE
TABLET - WEB
ACTIVATION OF REMOTE CONTROL
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
INSERTING THE BATTERIES
SAFETY WARNINGS
The remote control and batteries should not be exposed to excessive heat such as sunlight, re
or the like.
The product . Keep out of reach of children or domestic animals. is not a toy
This remote control, after inserting the batteries, is normally ready for use as it is already set at the
factory with a specic code.
If problems are found to command the TV, or some functions do not produce the desired eect, to follow the instructions
to the chapter ACTIVATION OF REMOTE CONTROL.
Remote control for TV sets ready to e TELEFUNKEN us
Use the -code on the side or connect to the page and follow the instructions. qr www.cme.it
Once you have found the specic code for your device, set it in the remote control as described in the
ENTERING THE CODE DIRECTLY chapter.
• Stand in front of the device to be controlled and make sure it is ON (not in stand-by). If necessary, switch
it on using the original remote control (if this is still working) or the buttons present on the device itself. (on
TVs they can be on the side or the top)
• On the MELICONI remote control press and hold the butt until the LED of the remote control lights on
up; lease. re
• Pointing the remote control towards the device, PRESS AND HOLD butt and wait the ON/OFF on
for the device to switch o.
• , w the device turn o IMMEDIATELY RELEASE the button. PAY ATTENTION hen ,
• Three nal ashes indicate that the operation has been completed successfully.
(only to be performed if you know the to be set) specic code
• On the MELICONI remote control press and hold the button until the LED lights up; release.
• Immediately enter the previously identied specic code.
• Three nal ashes indicate that the operation has been completed successfully.
If you want to delete the function in combination with a single button, operate as follows:
• On the MELICONI remote control press and hold the button.
• When the LED turn on enter the code ; release the buttons. , without releasing the button, 1600
• Within 30 seconds, press and hold the button of which you want to delete the function; wait three ashes indicating the end
of the operation, release the button. (to recall the original function, setting again the activation code)
DELETE FUNCTION BY SINGLE BUTTON
If the remote control does NOT carry out the three nal ashes, the setting is NOT successful; repeat the procedure.
If still unsuccessful, it means that the code is not included in the remote control, contact the ASSISTANCE.
ENTERING THE CODE DIRECTLY
VERIFY
Check that the MELICONI remote control operates your device the main functions if it does not, the in ; REPEAT
procedure.
NOTE: When the list of codes to be searched is over, the remote control exits the search and the LED remains o.
If after attempts no results are obtained, try using the procedure described in the SMARTPHONE - TABLET - WEB 8
chapter or contact the ASSISTANCE.
MANUAL SEARCH
SMARTPHONE - TABLET - WEB
watch
the video
watch
the video
The functions of the buttons on the MELICONI remote control are only available if the original device is equipped with it.
Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.
To enable them, connect to the page, use the on-line tool ACTIVATION OF REMOTE CONTROL and continue www.cme.it
until you see the list matching buttons between the original remote control and the MELICONI remote control.
To obtain some functions, press and hold the button and press the corresponding key indicated in the table.
If the function you want to play is matched with an number i color operate as follows: n orange ,
• On the MELICONI remote control press and hold the button.
• When the LED turn on , point the remote control towards the device , without releasing the button
and enter the previously identied number corresponding to the function you want to get. (at the last digit
pressure, the remote control already transmits this function)
• Release the buttons; to match the function obtained to a MELICONI remote control button, within 30
seconds, press and hold the desired button.
• Wait three ashes indicate that storage; release the button. (the used button loses the original function
that will be called by setting again the activation code)
For any future activation of the remote control, it is advisable to extract and note the code in use, operate as follows:
• On the MELICONI remote control press and hold the button until the LED lights up; release.
• Enter the code . 0010
• After a pause of several seconds, the LED produces four sets of ashes, spaced out,
corresponding to the code to be obtained. Count the number of ashes. Each set of ashes
corresponds to one digit in the code. Ten ashes correspond to the digit 0 . zero “ ”
( code obtained = example 1701)
• Make a note of the code obtained. You may need it in future.
If necessary it is possible to reset the remote control and bring it back to the initial conditions. completely
WARNING : All user settings will be lost. Operate as follows:
• On the MELICONI remote control press and hold the button until the LED lights up; release.
• Enter the code . 0100
• Three nal ashes indicate that the operation has been completed successfully.
RESET THE REMOTE CONTROL
DISPLAY CODE IN USE
BUTTONS AND FUNCTIONS

Specyfikacje produktu

Marka: Meliconi
Kategoria: Zdalne sterowanie
Model: Gumbody Personal 6 plus

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Meliconi Gumbody Personal 6 plus, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Zdalne sterowanie Meliconi

Meliconi

Meliconi Personal 2 plus Instrukcja

30 Września 2024
Meliconi

Meliconi gumbody light facile Instrukcja

23 Września 2024
Meliconi

Meliconi Speedy 2.1 Instrukcja

22 Września 2024
Meliconi

Meliconi GumBody Light Instrukcja

22 Września 2024
Meliconi

Meliconi universal 4 Instrukcja

22 Września 2024
Meliconi

Meliconi Pratico 2.1 Instrukcja

21 Września 2024
Meliconi

Meliconi Gumbody Personal 7 plus Instrukcja

21 Września 2024
Meliconi

Meliconi Gumbody Personal 2 Instrukcja

21 Września 2024
Meliconi

Meliconi Control TV+ Instrukcja

21 Września 2024
Meliconi

Meliconi Gumbody Personal 6 plus Instrukcja

21 Września 2024

Instrukcje Zdalne sterowanie

Najnowsze instrukcje dla Zdalne sterowanie

Neewer

Neewer RT112 Instrukcja

9 Października 2024
Neewer

Neewer RT113 Instrukcja

9 Października 2024
Zalman

Zalman ZM-VE350 Instrukcja

9 Października 2024
Canon

Canon BG-R20 Instrukcja

9 Października 2024
Canon

Canon BG-R20EP Instrukcja

9 Października 2024
Mosconi

Mosconi DSP6T8 Instrukcja

8 Października 2024
Mosconi

Mosconi RC MINI Instrukcja

8 Października 2024
Ridem

Ridem CRC UNB Instrukcja

8 Października 2024
Ridem

Ridem CRC UNW Instrukcja

8 Października 2024
ORNO

ORNO OR-GB-458 Instrukcja

8 Października 2024